INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NNAAMMEE IINNSSTTAALLLL - Installation procedure for NetBSD/atari DDEESSCCRRIIPPTTIIOONN AAbboouutt tthhiiss DDooccuummeenntt This document describes the installation procedure for NetBSD 1.4.2 on the _a_t_a_r_i platform. It is available in four different formats titled _I_N_S_T_A_L_L_._e_x_t, where _e_x_t is one of _._p_s, _._h_t_m_l, _._m_o_r_e, or _._t_x_t. _._p_s PostScript. _._h_t_m_l Standard internet HTML. _._m_o_r_e The enhanced text format used on Unix-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line _m_a_n pages are generally pre- sented. _._t_x_t Plain old ASCII. You are reading the _m_o_r_e version. WWhhaatt iiss NNeettBBSSDD?? The NetBSD Operating System is a fully functional Open Source UN*X-like operating system derived from the Berkeley Networking Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on twenty different system architectures featuring eight distinct families of CPUs, and is being ported to more. The NetBSD 1.4.2 release contains complete binary releases for fifteen different machine types. (The remaining ones are not fully supported at this time and are thus not part of the binary distri- bution. For information on them, please see the NetBSD web site at hhttttpp::////wwwwww..nneettbbssdd..oorrgg//) NetBSD is a completely integrated system. In addition to its highly portable, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, The X Window System, and nu- merous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. UUppggrraaddee ppaatthh ttoo NNeettBBSSDD 11..44..22 If you are not installing your system ``from scratch'' but instead are going to upgrade an existing system already running NetBSD you need to know which versions you can upgrade with NetBSD 1.4.2. NetBSD 1.4.2 is an upgrade of NetBSD 1.4.1, NetBSD 1.4 and earlier re- leases of NetBSD such as versions 1.3.3, 1.2 etc. The intermediate development versions of code available on the main trunk in our CVS repository (also known as ``NetBSD-current'') from _a_f_t_e_r the point where the release cycle for 1.4 was started are designated by ver- sion identifiers such as 1.4A, 1.4B, 1.4P etc. These identifiers do not designate releases, but indicate major changes in internal kernel APIs. Note that the kernel from NetBSD 1.4.2 can _n_o_t be used to upgrade a sys- tem running one of those intermediate development versions. Trying to use the NetBSD 1.4.2 kernel on such a system _w_i_l_l in all probability re- sult in problems. Please also note that it is not possible to do a direct ``version'' com- parison between any of the intermediate development versions mentioned above and 1.4.2 to determine if a given feature is present or absent in 1.4.2. The development of 1.4, 1.4.1 and 1.4.2 is done on a separate branch in the CVS repository which was created when the release cylcle for 1.4 was started, and during the release cycles for all these versions selective fixes (with minor impact on the stability of the code on the release branch) have been imported from the main development trunk. So, there are features in 1.4.2 which were not in e.g. 1.4H, but the reverse is also true. MMaajjoorr CChhaannggeess BBeettwweeeenn 11..44..11 aanndd 11..44..22 The complete list of changes between NetBSD 1.4.1 and 1.4.2 can be found in the file CHANGES-1.4.2 in the top directory of the source tree. The following are the highlights only. ++oo A driver for the Alteon Gigabit Ethernet cards has been added, see ti(4). ++oo A driver for the Realtek 8129/8239 Fast Ethernet PCI cards have been added, see rl(4). ++oo A driver for the DPT SmartCache and SmartRAID III or IV SCSI adapters has been added, see dpt(4). ++oo A driver for the BOCA IOAT66 6-port ISA serial adapter has been added, see ioat(4). ++oo Support for the X-surf Amiga board has been added. ++oo Support has been added for ext2fs revision 1, with read-only support for the ``sparse super'' and the ``filetype'' options. ++oo BIND has been upgraded to version 8.2.2-P5. ++oo The IPF packet filtering software has been updated to version 3.3.5. ++oo Tcpdump now does hex/ascii dumps of packet contents if asked to do so. ++oo An implementation of the System V user management utilities has been added. ++oo The name ``errno'' is now always a macro which expands to a function call. This is done to ease the integration of thread libraries with the code in both system and third-party libraries. Please include to access the correct definition of ``errno''. ++oo A utility for making temporary files for shell scripts has been added, see mktemp(1). ++oo The automounter utility amd(8) has been updated to fix a security problem. ++oo A security problem in procfs has been fixed. Procfs is not used by default in NetBSD. ++oo The floating point emulation on the ports using the m68k CPU has been reverted to the version in NetBSD 1.4 (the version in 1.4.1 had prob- lems). ++oo Several subsystems have received substantial work, such as RAIDframe, LFS, and the package tools. In addition, many, many bugs have been fixed -- more than 100 problems reported through our problem tracking system have been fixed, and many other non-reported problems have also been found and fixed. See the CHANGES-1.4.2 file for the complete list. KKnnoowwnn ccaavveeaattss wwiitthh 11..44..22 The following are the major known issues with NetBSD 1.4.2. ++oo The upgrade of ipf(8) caused a change of the kernel API. Thus, if you are using ipf(8) you need to upgrade both the kernel and the us- er-land utilities to control that feature in order for it to work. ++oo As part of fixing a kernel bug, ``struct vfsnode'' needed to change size. This will unfortunately, and contrary to tradition for patch releases, cause incompatibilities for users of file system LKMs com- piled for 1.4 and 1.4.1. ++oo Although LFS has been improved between 1.4.1 and 1.4.2, it can proba- bly still be characterized as being of ``beta test'' quality, e.g. filling the file system still gives ``interesting'' effects. It should probably not be used to store critical data quite yet. ++oo The version of the IPF packet filtering software in NetBSD 1.4.2 must be enabled with ``ipf -E'' before filtering or NAT rules can be set. Failure to do so may result in a panic. MMaajjoorr CChhaannggeess BBeettwweeeenn 11..44 aanndd 11..44..11 The complete list of changes between NetBSD 1.4 and 1.4.1 can be found in the file CHANGES-1.4.1 in the top directory of the source tree. ++oo The NetBSD/alpha port's compatibility for Digital UNIX executables has been greatly improved. ++oo Many bug fixes and improvements of the installation tools and utili- ties. ++oo Support for more PCI serial/parallel cards has been added. ++oo It is now possible to boot NetBSD/i386 on systems with 1GB of RAM. ++oo The floating point emulation on the ports using the m68k CPU has been upgraded. ++oo A fatal problem with /dev/random has been found and fixed. ++oo Support for Alpha 21264 ev6 based systems has been added to NetB- SD/alpha. MMaajjoorr CChhaannggeess BBeettwweeeenn 11..33 aanndd 11..44 The NetBSD 1.4 release is a substantial improvement over its predeces- sors. We have provided numerous significant functional enhancements, in- cluding support for many new devices, integration of hundreds of bug fix- es, new and updated kernel subsystems, and many userland enhancements. The results of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize the nearly two years of develop- ment that went into the NetBSD 1.4 release. Some highlights include: ++oo Substantial improvements in the TCP/IP implementation, including nu- merous performance enhancements and bug fixes by Jason Thorpe and others. ++oo A new, high efficiency kernel memory pool allocator by Paul Kranen- burg. This has been integrated into most kernel subsystems. ++oo A new, totally rewritten virtual memory subsystem, UVM, created by Chuck Cranor, which is substantially cleaner and better performing than the old Mach derived VM subsystem. ++oo Improved POSIX and XPG standards compliance. ++oo Completion of the integration of all remaining 4.4BSD Lite-2 kernel improvements and bug fixes that had not been previously integrated. (Integration of all userland components was completed before NetBSD 1.3) ++oo Several new ports, including macppc, bebox, sparc64, next68k, and others, have been integrated into the source tree. ++oo The system compilers have been upgraded to egcs 1.1.1, and the system compiler toolchain now (mostly) uses the latest versions of GNU binu- tils instead of the obsolete versions left over from 4.4BSD Lite. ++oo Everyone's favorite ftp(1) client has been improved even further. See the man page for details. ++oo A new architecture independent console driver, wscons(4), has been integrated into many ports. ++oo Numerous improvements have been made to the audio subsystem support, including support for MIDI device drivers. ++oo Linux compatibility support has been improved. ++oo A number of scheduler enhancements have yielded dramatic improvements in interactive performance and better control of background tasks. ++oo Several network tunneling protocols, including GRE and IP in IP, have been implemented. ++oo Kernel support for the CODA distributed file system has been added. ++oo Manuel Bouyer completed major changes to the IDE support. It is now architecture independent. Major changes have been made to the IDE code for better error handling, improved ATAPI support, 32 bit data I/O support and bus-master DMA support on PCI IDE controllers. ++oo Lennart Augustsson has added full USB support, permitting the use of a wide variety of Universal Serial Bus peripherals. The drivers should easily port to any future platforms that support the PCI bus. See usb(4) for an overview. ++oo RAIDframe, version 1.1, from the Parallel Data Laboratory at Carnegie Mellon University, has been integrated. Supports RAID levels 0, 1, 4, 5, and more. ++oo Luke Mewburn added nsswitch.conf(5) functionality to the system to specify the search order for system databases. ++oo syslogd(8) now supports listening on multiple sockets, to make the chrooting of servers easier. ++oo Most third party packages have been updated to the latest stable re- lease. As has been noted, there have also been innumerable bug fixes. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. The Atari release stepped in in March 1995. The first official release was NetBSD 1.1. About a year later, NetBSD 1.2 was released for the Atari. This release fixed a large number of bugs and made the Atari-port a stable member of the NetBSD family. The saga continued with the NetBSD 1.3 release. In this release, support was added for the Medusa Hades, Riebl ethernet and Falcon IDE support. And now, yet another re- lease is emerging! New on the NetBSD 1.4 release (atari specific): ++oo Crazy Dots VME et4000 graphics adapter ++oo Circad Leonardo 24-bit VME graphics adapter ++oo VME BVME410 ethernet ++oo ATAPI support on IDE ++oo Hades PCI-devices -- Adaptec 2940U ++oo Hades ISA-devices -- Teles 16.3 card (Requires isdn4bsd package). TThhee FFuuttuurree ooff NNeettBBSSDD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: ++oo providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. ++oo providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. ++oo providing a better position from which to undertake promotional ac- tivities. ++oo periodically organizing workshops for developers and other interested people to discuss ongoing work. We intend to begin narrowing the time delay between releases. Our ambi- tion is to provide a full release every six to eight months. We hope to support even _m_o_r_e hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. In addition, Anonymous CVS access to the NetBSD source tree has been added since NetBSD 1.4.1; see hhttttpp::////wwwwww..nneettbbssdd..oorrgg//CChhaannggeess//##aannoonnccvvss--aavvaaiillaabbllee We have also added a browsable CVS repository on the web at hhttttpp::////ccvvsswweebb..nneettbbssdd..oorrgg//ccggii--bbiinn//ccvvsswweebb..ccggii// We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the us- ability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. SSoouurrcceess ooff NNeettBBSSDD Please refer to hhttttpp::////wwwwww..nneettbbssdd..oorrgg//SSiitteess//nneett..hhttmmll. NNeettBBSSDD 11..44..22 RReelleeaassee CCoonntteennttss The root directory of the NetBSD 1.4.2 release is organized as follows: _._._._/_N_e_t_B_S_D_-_1_._4_._2_/ BUGS Known bugs list (somewhat incomplete and out of date). CHANGES Changes since earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 1.4.2 distribution. README.files README describing the distribution's contents. TODO NetBSD's todo list (also somewhat incomplete and out of date). patches/ Post-release source code patches. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one di- rectory per architecture, for each of the architectures for which NetBSD 1.4.2 has a binary distribution. There are also 'README.export- control' files sprinkled liberally throughout the distribution tree, which point out that there are some portions of the distribution (i.e. the `domestic' portion) that may be subject to export regulations of the United States. It is your responsibility to determine whether or not it is legal for you to export these portions and to act accordingly. The NetBSD project maintains a web page at hhttttpp::////wwwwww..NNeettBBSSDD..OORRGG//MMiisscc//ccrryyppttoo--eexxppoorrtt..hhttmmll which should contain up-to-date information on this issue. The source distribution sets can be found in subdirectories of the "source" subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: secrsrc.tgz: This set contains the "domestic" sources. These sources may be subject to United States export regulations. _4_2_1_K _g_z_i_p_p_e_d_, _2_M _u_n_c_o_m_p_r_e_s_s_e_d gnusrc.tgz: This set contains the "gnu" sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. _1_9_M _g_z_i_p_p_e_d_, _8_4_._3_M _u_n_c_o_m_p_r_e_s_s_e_d syssrc.tgz: This set contains the sources to the NetBSD 1.4.2 ker- nel, config(8), and dbsym(8). _1_3_._9_M _g_z_i_p_p_e_d_, _6_8_._3_M _u_n_c_o_m_p_r_e_s_s_e_d sharesrc.tgz: This set contains the "share" sources, which include the sources for the man pages not associated with any par- ticular program, the sources for the typesettable docu- ment set, the dictionaries, and more. _3_M _g_z_i_p_p_e_d_, _1_1_._9_M _u_n_c_o_m_p_r_e_s_s_e_d src.tgz: This set contains all of the NetBSD 1.4.2 sources which are not mentioned above. _1_4_._4_M _g_z_i_p_p_e_d_, _6_7_._4_M _u_n_c_o_m_p_r_e_s_s_e_d Most of the above source sets are located in the _s_o_u_r_c_e_/_s_e_t_s subdirectory of the distribution tree. The secrsrc.tgz set is contained in the _s_o_u_r_c_e_/_s_e_c_u_r_i_t_y subdirectory. This set, which may only be available to users in the United States and Canada, contains the sources normally found in _/_u_s_r_/_s_r_c_/_d_o_m_e_s_t_i_c - primarily Kerberos and other cryptographic security related software. (Remember, because of United States law, it may not be legal to distribute this set to locations outside of the Unit- ed States and Canada. Again, see hhttttpp::////wwwwww..NNeettBBSSDD..OORRGG//MMiisscc//ccrryyppttoo--eexxppoorrtt..hhttmmll for updated information on this issue.) The source sets are distributed as compressed tar files. They may be un- packed into _/_u_s_r_/_s_r_c with the command: ccaatt sseett__nnaammee..ttggzz || gguunnzziipp || ((ccdd //;; ttaarr xxppff -- )) The _s_e_t_s_/_S_p_l_i_t_/ and _s_e_c_u_r_i_t_y_/_S_p_l_i_t_/ subdirectories contain split versions of the source sets for those users who need to load the source sets from floppy or otherwise need a split distribution. The split sets are are named "set_name.xx" where "set_name" is the distribution set name, and "xx" is the sequence number of the file, starting with "aa" for the first file in the distribution set, then "ab" for the next, and so on. All of these files except the last one of each set should be exactly 240,640 bytes long. (The last file is just long enough to contain the remainder of the data for that distribution set.) The split distributions may be reassembled and extracted with ccaatt as follows: ccaatt sseett__nnaammee..???? || gguunnzziipp || ((ccdd //;; ttaarr xxppff -- )) In each of the source distribution set directories, there is a file named _C_K_S_U_M_S which contains the checksums of the files in that directory, as generated by the cksum(1) utility. You can use cksum to check the in- tegrity of the archives, if you suspect that one of the files is corrupt and have access to a cksum binary. Checksums based on other algorithms may also be present - see the release(7) man page for details. _N_e_t_B_S_D_/_a_t_a_r_i _S_u_b_d_i_r_e_c_t_o_r_y _S_t_r_u_c_t_u_r_e The atari-specific portion of the NetBSD 1.4.2 release is found in the _a_t_a_r_i subdirectory of the distribution: _._._._/_N_e_t_B_S_D_-_1_._4_._2_/_a_t_a_r_i_/ _I_N_S_T_A_L_L_._h_t_m_l _I_N_S_T_A_L_L_._p_s _I_N_S_T_A_L_L_._t_x_t _I_N_S_T_A_L_L_._m_o_r_e Installation notes; this file. The _._m_o_r_e file contains underlined text using the more(1) conventions for indicat- ing italic and bold display. _b_i_n_a_r_y_/ _s_e_t_s_/ atari binary distribution sets; see below. _s_e_c_u_r_i_t_y_/ atari security distribution; see below. _i_n_s_t_a_l_l_a_t_i_o_n_/ _B_i_n_a_r_y _D_i_s_t_r_i_b_u_t_i_o_n _S_e_t_s The NetBSD atari binary distribution sets contain the binaries which com- prise the NetBSD 1.4.2 release for the atari. There are eight binary dis- tribution sets and the _s_e_c_u_r_i_t_y distribution set. The binary distribu- tion sets can be found in the _a_t_a_r_i_/_b_i_n_a_r_y_/_s_e_t_s subdirectory of the NetBSD 1.4.2 distribution tree, and are as follows: bbaassee The NetBSD 1.4.2 atari bbaassee binary distribution. You _m_u_s_t install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally functional. It includes shared library support, and excludes everything described below. _1_0_._3_M _g_z_i_p_p_e_d_, _2_9_._0_M _u_n_c_o_m_p_r_e_s_s_e_d ccoommpp Things needed for compiling programs. This set includes the system include files (_/_u_s_r_/_i_n_c_l_u_d_e) and the various system libraries (except the shared libraries, which are included as part of the bbaassee set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. _8_._1_M _g_z_i_p_p_e_d_, _2_7_._2_M _u_n_c_o_m_p_r_e_s_s_e_d eettcc This distribution set contains the system configuration files that reside in _/_e_t_c and in several other places. This set _m_u_s_t be installed if you are installing the system from scratch, but should _n_o_t be used if you are upgrading. (If you are upgrading, it's recommended that you get a copy of this set and _c_a_r_e_f_u_l_l_y upgrade your configuration files by hand.) _5_6_K _g_z_i_p_p_e_d_, _3_3_0_K _u_n_c_o_m_p_r_e_s_s_e_d ggaammeess This set includes the games and their manual pages. _2_._8_M _g_z_i_p_p_e_d_, _7_M _u_n_c_o_m_p_r_e_s_s_e_d nneettbbssdd..**..ggzz The NetBSD/atari 1.4.2 kernel binary. You should install the appropriate kernel for your system. _A_p_p_r_o_x_. _5_0_0_K _g_z_i_p_p_e_d_, _1_M _u_n_c_o_m_p_r_e_s_s_e_d mmaann This set includes all of the manual pages for the binaries and other software contained in the bbaassee set. Note that it does not include any of the manual pages that are included in the other sets. _4_M _g_z_i_p_p_e_d_, _1_5_._9_M _u_n_c_o_m_p_r_e_s_s_e_d mmiisscc This set includes the (rather large) system dictionaries, the typesettable document set, and other files from _/_u_s_r_/_s_h_a_r_e. _2_._2_M _g_z_i_p_p_e_d_, _8_._4_M _u_n_c_o_m_p_r_e_s_s_e_d tteexxtt This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. _1_._3_M _g_z_i_p_p_e_d_, _4_._5_M _u_n_c_o_m_p_r_e_s_s_e_d The atari security distribution set is named sseeccrr and can be found in the _a_t_a_r_i_/_b_i_n_a_r_y_/_s_e_c_u_r_i_t_y subdirectory of the NetBSD 1.4.2 distribution tree. It contains security- related binaries which depend on cryptographic source code. You do not need this distribution set to use encrypted passwords in your password file; the bbaassee distribution includes a crypt library which can perform only the one-way encryption function. The security distribution includes a version of the Kerberos IV network security system, and a Kerberized version of telnet(1) program. The sseeccrr distribution set can be found only on those sites which carry the complete NetBSD distribution and which can legally obtain it. Because of United States law, it may not be legal to distribute this set to locations outside of the United States and Canada. See hhttttpp::////wwwwww..NNeettBBSSDD..OORRGG//MMiisscc//ccrryyppttoo--eexxppoorrtt..hhttmmll for updated information on this issue. NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 3.3.6. Binary sets for the X Window system are distributed with NetBSD. The sets are: xxbbaassee The basic files needed for a complete X client environment. This does not include the X servers. _2_._5_M _g_z_i_p_p_e_d _7_._9_M _u_n_c_o_m_p_r_e_s_s_e_d xxccoommpp The extra libraries and include files needed to compile X source code. _1_._6_M _g_z_i_p_p_e_d_, _6_._8_M _u_n_c_o_m_p_r_e_s_s_e_d xxccoonnttrriibb Programs that were contributed to X. _1_7_9_k _g_z_i_p_p_e_d_, _6_7_0_k _u_n_c_o_m_p_r_e_s_s_e_d xxffoonntt Fonts needed by X. _5_._7_M _g_z_i_p_p_e_d_, _7_._0_M _u_n_c_o_m_p_r_e_s_s_e_d xxsseerrvveerr The Xservers and some programs not shared with the other m68k ports. Please consult the X specific section in the atari FAQ as to which server you should use. _6_._3_M _g_z_i_p_p_e_d_, _1_5_._7_M _u_n_c_o_m_p_r_e_s_s_e_d The atari binary distribution sets are distributed as gzipped tar files named with the extension ..ttggzz, e.g. _b_a_s_e_._t_g_z. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the files are /-relative and therefore are extracted _b_e_l_o_w the current directory. That is, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the ttaarr xxffpp command from /. Additional kernels to those included in the distribution sets may be found in the _a_t_a_r_i_/_b_i_n_a_r_y_/_k_e_r_n_e_l subdirectory of the NetBSD 1.4.2 distri- bution tree. These kernels are generally named something like _n_e_t_b_s_d_._B_O_O_T_._g_z or some other suitable name. Please note that these ker- nels are simply gzipped and are not in tar archives. There are three atari floppy images to be found in the _a_t_a_r_i_/_i_n_s_t_a_l_l_a_t_i_o_n_/_f_l_o_p_p_i_e_s subdirectory of the NetBSD 1.4.2 distribu- tion. One of them is a bootable TOS kernel floppy and the other two are installation floppies. They are described in more detail below. There are gzipped versions of each available, for easier downloading. (The gzipped versions have the _._g_z extension added to their names.) _B_o_o_t_a_b_l_e _K_e_r_n_e_l _f_l_o_p_p_y This TOS disk contains the loadbsd and chg_pid programs and a kernel. It is setup so that you can insert it int your floppy drive, and start the programs from GEM. For the TT030 and Falcon, the (720KB) floppy is named boot.fs and the kernel supplied is 'BOOT'. For the Hades, you need the hades- boot.fs floppy (1.44MB), the kernel is 'HADES'. _I_n_s_t_a_l_l_a_t_i_o_n _f_l_o_p_p_y_: This disk contains a BSD root file system setup to help you in- stall the rest of NetBSD. This includes formatting and mounting your root and /usr partitions and getting ready to extract (and possibly first fetching) the distribution sets. There is enough on this file system to allow you to make a slip connection, con- figure an ethernet, mount an NFS file system or ftp. You can also load distribution sets from a SCSI tape or from one of your ex- isting GEMDOS partitions. The floppies meant for 720KB disks are named _m_i_n_i_r_o_o_t_._f_s_._1 and _m_i_n_i_r_o_o_t_._f_s_._2. There is also an image for an 1.44MB disk: _m_i_n_i_r_o_o_t_._f_s. There are also TOS utilities in the _a_t_a_r_i_/_i_n_s_t_a_l_l_a_t_i_o_n_/_m_i_s_c subdirectory, which you will need to get NetBSD/Atari 'up-and-running'. ++oo The ``gzip.ttp'' program allows you to uncompress .gz images. The us- age is "gzip.ttp -d filename.gz". ++oo The ``rawwrite.ttp'' program allows you to create the installation floppy disks from the files in the _a_t_a_r_i_/_f_l_o_p_p_i_e_s directory. ++oo The "aptck.ttp" program reads the partition tables present on a given disk and tries to interpret then the same way the NetBSD kernel does. If you have a disk on which GEMDOS and NetBSD are to co-exist, It is a good idea to run this before you begin the NetBSD/Atari installa- tion just to check that the kernel's view of the partition tables agree with GEMDOS's view. If you have more than 3 partitions defined on a disk you will notice that the NetBSD/atari partition starts one sector after the GEMDOS partition. This is to allow space for the auxilliary root for the 4th and subsequent partitions. ++oo The "loadbsd.ttp" program loads the NetBSD/atari kernel from TOS (or MiNT, MultiTOS, etc.). _N_o_t_e Each directory in the atari binary distribution also has its own checksum files, just as the source distribution does: All BSDSUM files are historic BSD checksums for the various files in that directory, in the format produced by the command: cckkssuumm --oo 11 _f_i_l_e All CKSUM files are POSIX checksums for the various files in that directory, in the format produced by the command: cckkssuumm _f_i_l_e. All MD5 files are MD5 digests for the various files in that direc- tory, in the format produced by the command: cckkssuumm --mm _f_i_l_e. All SYSVSUM files are historic AT&T System V UNIX checksums for the various files in that directory, in the format produced by the command: cckkssuumm --oo --22 _f_i_l_e. The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest possible range of system can check the integrity of the release files. NNeettBBSSDD//aattaarrii SSyysstteemm RReeqquuiirreemmeennttss aanndd SSuuppppoorrtteedd DDeevviicceess NetBSD/atari 1.4.2 runs on a TT030, Falcon and Hades. An FPU is not re- quired. The minimum amount of RAM required is 4Mb. On the Hades, only the Tseng PCI VGA cards (et4000/et6000/et6100) are supported in the 1.4.2 release. When an unsupported video card is present, you can use NetBSD with a serial console only. Here is a table of recommended HD partition sizes for a full install: partition: advise, with X, needed, with X root (/) 20M 20M 15M 15M user (/usr) 95M 125M 75M 105M swap ----- 2M for every M ram ----- local (/local) up to you In addition of the rule of thumb for the swap size mentioned below, you probably want to make sure that the size of the swap partition does not drop below 20Mb (30Mb for systems with X). Another item are the add-on packages. You might want 20-30M (or more) in /local (or added to /usr) to store packages from the NetBSD package system. As you may note the rec- ommended size of /usr is 20M greater than needed. This is to leave room for a kernel source and compile tree as you will probably want to compile your own kernel. (GENERIC is large and bulky to accommodate all people, BOOT is small and might not have all the features you want). Supported devices include: ++oo The builtin SCSI host adapter -- Should support most SCSI-drives. -- Should support most tape drives. -- Should support most CD-ROM drives. -- Should support most ZIP/MO drives. ++oo The builtin video controller ++oo The builtin (720Kb/1.44Mb) floppydrive ++oo The serial2/modem2 ports ++oo The Falcon FX memory expansion ++oo The atari mouse ++oo A 3-button mouse (see build description in the FAQ!) ++oo The parallel printer ++oo IDE interface on both Falcon and Hades (includes ATAPI support) ++oo The serial interface on the first 68901 UART (modem1) ++oo VME-bus devices (TT030/Hades) -- BVME410 ethernet -- Circad Leonardo 24-bit VME graphics adapter -- Crazy Dots VME et4000 graphics adapter -- Riebl (and possibly PAM) ethernet cards on the VME bus. ++oo PCI-bus devices (Hades only) -- ET4000/ET6000/ET6100-PCI (VGA console) -- Adaptec 2940U ++oo ISA-bus devices (Hades only) -- Teles S0/16.3-ISA ISDN adapter (with I4B) This list is incomplete by definition. I can not test all SCSI peripher- als, ISA cards or PCI cards... If you have problems with such a peripher- al, please contact the port-atari mailing list. GGeettttiinngg tthhee NNeettBBSSDD SSyysstteemm oonn ttoo UUsseeffuull MMeeddiiaa Installation is supported from several media types, including: ++oo TOS HD partitions ++oo Tape No matter what you do, however, you'll need to have three disks handy, on which you will put the install and boot floppy images. All the images are available from the directory "installation/floppies" under the root of the NetBSD/atari tree at your favorite archive site. If you are using NetBSD/atari to make the floppies, you should use the command dd(1) to write the raw floppy images (.fs files) to the disk. As an example, to write the first part of the miniroot filesystem onto a 720KB floppy in fd0 use: dd if=miniroot.fs.1 of=/dev/rfd0b bs=9b If you are using TOS to make the floppies, grab the 'rawwrite' utility from the "atari/utils" directory and issue the command: rawwrite boot.fs This will create the boot-floppy on the floppy in drive a. The floppies should be pre-formatted on 720Kb/1.44Mb for both the 'dd' and 'rawwrite' commands to work. Pre-formatting can be best done using the desktop for- mat command. Some other utilities seem to be giving problems. Since the 1.3 release, it is also possible to use HD-floppies. You should than use the floppy device '/dev/rfd0c' or add the '-H' flag to 'rawwrite'. The steps necessary to prepare the distribution sets for installation de- pend on which method of installation you choose. The various methods are explained below. ++oo To prepare for installing via an GEMDOS partition: To install NetBSD from an GEMDOS partition, you need to get the NetB- SD distribution sets you wish to install on your system on to an GEM- DOS partition. Note where you placed the files, you will need this later. Once you have done this, you can proceed to the next step in the in- stallation process, preparing your hard disk. ++oo To prepare for installing via a tape: To install NetBSD from a tape, you need to somehow get the NetBSD filesets you wish to install on your system on to the appropriate kind of tape. If you make the tape on a UN*X-like system, you can create it as follows: cd .../NetBSD-1.3/atari/binary/sets T= mt -f $T rewind for f in base etc comp games man misc text dd if=$f.tgz of=$T conv=sync bs=5k done mt -f $T rewind where "" is the name of the (non-rewinding!) tape device that you're using (probably something like /dev/nrst0, but we make no guarantees 8-). If you can't figure it out, ask your system adminis- trator. Once you have done this, you can proceed to the next step in the in- stallation process, preparing your hard disk. PPrreeppaarriinngg yyoouurr SSyysstteemm ffoorr NNeettBBSSDD IInnssttaallllaattiioonn Note you will be modifying your HD's if you mess something up here you could lose everything on all the drives that you work with. It is there- fore advised that you: ++oo Write down your current configurations. Do this by writing down all partition info (especially their sizes). ++oo _B_a_c_k _u_p _t_h_e _p_a_r_t_i_t_i_o_n_s _y_o_u _a_r_e _k_e_e_p_i_n_g_. If NetBSD has a disk of it's own, you can delay the partitioning until the installer requests you to do it. This means that you can safely skip the rest of this section. If NetBSD has to share the disk with another operating system, you must take care of partitioning your harddisk before installing NetBSD; creat- ing space for at least root, swap and /usr partitions and possibly at least one more for /local if you have the space. _N_o_t_e The AHDI partioning function erases all partions on your harddisk even if they are not changed! I know this is rather stupid, but don't say I didn't warn you. If you want to use an AHDI partitioning sceme and you want to be able to boot directly into NetBSD, there are some constraints on the partition layout. As you might know; every hard disk has a "root sector" that contains in- formation about the size of the hard disk and the partitions on the hard disk. The root sector can only contain the neccessary data for four par- titions. Nobody thought that this limitation would cause any problems. After all, 640 KByte should be enough. As hard disk grew, it was necces- sary to define more than four partitions. In order to be more or less compatible with the old format, a new type of partition entry was de- fined: XGM partions. An XGM partition is a "look over there" sign: Another root sector can be found at the start of the XGM partition. This root sector contains the remaining real partitions. And this is the big mystery: Partitions de- fined in the root sector of the hard disk are called "primary parti- tions", partitions defined in the root sector of an XGM partition are called "extended partitions". The bootblock will only work if the first NBD partition is a primary par- tition. This is not a limitation of NetBSD but a limitation of TOS/AHDI: You can only boot from primary partitions. If you are creating your partitions with HDX, you'll have to be very careful to fulfill this rule. HDX has some very strange ideas when it comes to extended partitions. Fortunately, you can edit this stuff: The "Edit partition scheme of the unit" dialog box has a button label "ex- pert". This button is inactive unless you have defined more than four partitions. Click on it *after* you have defined the sizes of the parti- tions. A new dialog box appears on the screen. The left side contains two blocks of partitions: The upper block always contains the first four partitions, the lower block contains the last three partitions. If you have defined less than 7 partitions, some fields of the lower block will contain the string "unused". Some of the partitions will be displayed in reverse video: These are the extended partitions. The right side contains six possible ranges for the extended partitions. It is not possible to define your own range, you will have to use one of the schemes offered by HDX. To quote from Ghostbusters: Choose and die. The default scheme used by HDX is the first scheme: Extended partitions start with the second partition and end with the second to last parti- tion. If you have defined 7 partitions, partitions #2 to #5 will be ex- tended partitions, while partitions #1, #6 and #7 will be primary parti- tions. You can move the extended partition range by clicking on one of the but- tons on the right side of the dalog box. Try to find one where your first NetBSD partition is a primary partition. Golden rules: ++oo If the disk contains no GEMDOS partitions, don't use AHDI. Let NetBSD handle it alone. ++oo If the disk contains one GEMDOS partition, make it partition #1 and start the extended partition range at partition #3. This allows you to boot from both the GEMDOS and the NetBSD partitions. ++oo If the disk contains two GEMDOS partitions, use partitions #1 and #2 for GEMDOS, partition #3 for NetBSD-root. Start the extended parti- tion range with partition #4. ++oo If your disks contains three or more GEMDOS partitions, you are in trouble. Try using partitions #1 and #2 as the first two GEMDOS par- titions. Use partition #3 as the first NetBSD partition. Start the extended partition range with partition #4. Put the other NetBSD ex- tended partition range. Good luck, you'll need it... IInnssttaalllliinngg tthhee NNeettBBSSDD SSyysstteemm Installing NetBSD is a relatively complex process, but, if you have this document in hand and are careful to read and remember the information which is presented to you by the install program, it shouldn't be too much trouble. Before you begin, you must have already prepared your hard disk as de- tailed in the section on preparing your system for install. The following is a walk-through of the steps necessary to get NetBSD in- stalled on your hard disk. If you wish to stop the installation, you may hit Control-C at any prompt, but if you do, you'll have to begin again from scratch. 1. Booting the miniroot First you need to get yourself into NetBSD. This can be done in a couple ways, both of which currently require GEMDOS. You need either the bootfloppy provided in the distribution or you can copy the loadbsd.ttp program and kernel to a boot floppy disk (1.4M needed) or put them on a TOS partition. Select the load- bsd program and it will ask for parameters, supply: '-b netbsd' (or whatever name you copied the kernel to). You can, of course, also run it from the shell command-line in MiNT: loadbsd -b a:/netbsd You should see the screen clear and some information about your sys- tem as the kernel configures the hardware. Then you will be prompt- ed for a root device. At this time remove the GEMDOS kernel boot floppy from the drive if present and insert the BSD install floppy 1. Now type `md0a' to tell the kernel to load the install filesys- tem into RAMdisk. While While the kernel is loading, it will show a '.' for each track loaded. After loading 80 tracks, it will ask you to insert the next floppy. At this time, insert the BSD install floppy 2 and hit any key. The kernel continous loading another 40 tracks before it continues to boot. Note: If you are using 1.44Mb floppies, you should select 'md1a' instead of 'md0a'. The system should continue to boot. For now ignore WARNING: mes- sages about bad dates in clocks. Eventually you will be be asked to enter the pathname of the shell, just hit return. After a short while, you will be asked to select the type of your keyboard. After you have entered a valid response here, the system asks you if you want to install or upgrade your system. Since you are reading the 'install' section, 'i' would be the proper response here... 2. Entering the installer The installer starts with a nice welcome mes- sage. Read this message carefully, it also informs you of the risks involved in continuing! If you still want to go on, type 'y'. The installer now continues by trying to figure out your disk configura- tion. When it is done, you will be prompted to select a root device from the list of disks it has found. 3. Select your root device You should know at this point that the disks are NOT numbered according to their scsi-id! The NetBSD kernel num- bers the scsi drives (and other devices on the scsi bus) sequential- ly as it finds them. The drive with the lowest scsi id will be called sd0, the next one sd1, etc. Where you end up after the se- lection of the root disk depends on the contents of your disk. If it is already partitioned using AHDI, start reading at item 4a, if this disk has no AHDI partitioning but is blank or used by another non- AHDI system, start at item 4b. _Y_o_u _a_r_e _n_o_w _a_t _t_h_e _p_o_i_n_t _o_f _n_o _r_e_t_u_r_n_! The programs in section 4 will modify your harddisk. Type Control-C _n_o_w if you don't want this. 4. Setting AHDI partition id's on your root disk (using edahdi) Because NetBSD imposes a special ordering in disk partitions it uses for root and swap. And because it wants to guard you against an unwanted demolition of partitions used by other systems, you have to tell it what partitions it is allowed to use. You have to mark the partition you want to use as swap 'NBS' or 'SWP' and the other partitions as 'NBD'. Note that all the changes you make to the id's are reversable as long as you remember the original value. In the partition-id ed- itor, the partitions are shown in the order that AHDI created them. When you leave this editor and continue at item 4b, your changes to the id's do have consequences to the partition order! They will show up as follows: a - the first NBD partition b - the first NBS partition d (and up) - the rest of the partitions in AHDI order 5. Labeling your root disk (using edlabel) You are now allowed to change the partitioning of your disk. If your disk is already parti- tioned with AHDI DON'T change anything unless you are absolutely sure what you are doing! If you are labeling an empty SCSI disk, you can make life easy for yourself by selecting 'standarize geome- try'. This allows you to select a 'sectors per track' and 'tracks/cylinder' value and have the (fictious) SCSI geometry changed accordingly. So if you select 64 sect/track and 32 tracks/cylinder, each cylinder is exactly 1Mb in size. Well, go ahead and don't forget to save your work before you quit! Note: to make sure that NetBSD can create/mount filesystems on the partitions you defined, make sure the 'type' is entered cor- rectly: 4.2BSD - filesystems created by NetBSD MSDOS - filesystems shared with GEM 6. Label additional disks Now that your root-disk is labeled, you are given the opportunity to label any of the other disks in your sys- tem. The procedure is the same as with your root disk. 7. Setup the fstab Since all disks you want to use with NetBSD are properly labeled, it is time to tell the installer which partition will be associated with the different filesystems. As mentioned above, it is wise to make at least a separate root and /usr filesys- tem. Depending on what you are planning to do with your system, you might also consider to make a separate /var, /local or /home. When you tell the installer that all of your filesystems are specified correctly, it starts creating them for you. 8. Configure your network Currently none of the kernels supplied in the distribution has network support builtin. If you compiled your own kernel, network configuration mostly works. [ Due to space limitia- tions, some of the network commands are not present on the install floppy ] 9. Edit the fstab - again.... Since the network configuration might have lead to additional (nfs) filesystem entries, you get another chance to modify your fstab. 10. Installing the distribution sets You are finally at the point where some real data will be put on your freshly-made filesystems. Select the device type you whish to install from and off you go.... Some notes: ++oo If you want to install from tape, please read the section about how to create such a tape. The tape device name will be "nrst0" for the first tape drive, "nrst1" for the second, etc. ++oo Install at least the base and etc sets. ++oo If you have to specify a path relative to the mount-point and you need the mount-point itself, enter '.'. ++oo For previous NetBSD users: If you want to install from a GEMDOS filesystem, you don't need to rename the distribution sets as you may have done in previous versions of NetBSD. 11. Timezone selection and device-node building The isn't much to say about this. Just select the timezone you are in. The installer will make the correct setup on your root filesystem. After the timezone- link is installed, the installer will proceed by creating the device nodes on your root filesystem. Be patient, this will take a while... 12. Installing the kernel Because the kernel didn't fit on the install- disks, the installer asks you about the disk your kernel is on. You can specify the floppy with disk 'fd0' and partition 'b' for 720K disks and partition 'c' for 1.4M disks, or one of the hard disk par- titions. 13. Installing the bootstrap Finally, the installer ask you if you want to install the bootblock code on your root disk. This is a matter of personal choise and can also be done from a running NetBSD system. See the 'installboot(8)' manual page about how to do this. 14. You did it! Congratulations, you just installed NetBSD successful- ly! If you also installed a bootblock, you only have to reboot your atari to enter your freshly build system. If you didn't, get back to section 1 (How to boot the miniroot). Just substitute 'md0a' by your NetBSD root disk. _S_o_m_e _E_x_t_r_a _R_e_m_a_r_k_s If you don't want to use the bootloader. You could use the following set- up: ++oo Reserve a small GEMDOS partition of about 4Mb. This is enough to put in a few kernels. Put the netbsd kernel into this partition. Also, edit your /etc/fstab to always mount this partition, say as /kernels. Now make a symlink from /netbsd to /kernels/netbsd. This sceme is particulary handy when you want to make your own kernel. When compi- lation is finished, you just copy your kernel to /kernels/netbsd and reboot. It's wise to make sure there is _always_ a 'known to work' kernel image present. PPoosstt iinnssttaallllaattiioonn sstteeppss Once you've got the operating system running, there are a few things you need to do in order to bring the system into a propperly configured state, with the most important ones described below. 1. Configuring _/_e_t_c_/_r_c_._c_o_n_f If you haven't done any configuration of _/_e_t_c_/_r_c_._c_o_n_f, the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root filesystem mounted read-write. When the system asks you to choose a shell, simply hit return to get to a prompt. If you are asked for a terminal type, respond with vvtt222200 (or whatever is appropriate for your terminal type) and hit return. At this point, you need to configure at least one file in the _/_e_t_c directory. Change to the _/_e_t_c directory and take a look at the _/_e_t_c_/_r_c_._c_o_n_f file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi-user boot can proceed. If your _/_u_s_r directory is on a separate partition and you do not know how to use 'ed' or 'ex', you will have to mount your _/_u_s_r partition to gain access to 'vi'. Do the follow- ing: mmoouunntt //uussrr eexxppoorrtt TTEERRMM==vvtt222200 If you have _/_v_a_r on a seperate partition, you need to repeat that step for it. After that, you can edit _/_e_t_c_/_r_c_._c_o_n_f with vi(1). When you have finished, type eexxiitt at the prompt to leave the single-user shell and continue with the multi-user boot. Other values that need to be set in _/_e_t_c_/_r_c_._c_o_n_f for a networked en- vironment are _h_o_s_t_n_a_m_e and possibly _d_e_f_a_u_l_t_r_o_u_t_e, furthermore add an _i_f_c_o_n_f_i_g___i_n_t for your interface , along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have _m_y_n_a_m_e_._m_y_._d_o_m in _/_e_t_c_/_h_o_s_t_s: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an _/_e_t_c_/_r_e_s_o_l_v_._c_o_n_f file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Other files in _/_e_t_c that are new to NetBSD 1.4 and may require modi- fication or setting up include _/_e_t_c_/_m_a_i_l_e_r_._c_o_n_f, _/_e_t_c_/_n_s_s_w_i_t_c_h_._c_o_n_f and _/_e_t_c_/_w_s_c_o_n_s_._c_o_n_f. 2. Logging in After reboot, you can log in as root at the login prompt. There is no initial password, but if you're using the machine in a networked environment, you should create an account for yourself (see below) and protect it and the "root" account with good passwords. 3. Adding accounts Use the vipw(8) command to add accounts to your system, _d_o _n_o_t edit _/_e_t_c_/_p_a_s_s_w_d directly. See adduser(8) for more information on the process of how to add a new user to the system. 4. The X Window System If you have installed the X window system, look at the files in _/_u_s_r_/_X_1_1_R_6_/_l_i_b_/_X_1_1_/_d_o_c for information. Don't forget to add _/_u_s_r_/_X_1_1_R_6_/_b_i_n to your path in your shell's dot file so that you have access to the X binaries. 5. Installing 3rd party packages There is a lot of software freely available for Unix-based systems, almost all of which can run on NetBSD. Modifications are usually needed to when transferring programs between different Unix-like systems, so the NetBSD packages collection incorporates any such changes necessary to make that software run on NetBSD, and makes the installation (and deinstallation) of the software packages easy. There's also the option of building a package from source, in case there's no precompiled binary available. Precompiled binaries can be found at ffttpp::////ffttpp..nneettbbssdd..oorrgg//ppuubb//NNeettBBSSDD//ppaacckkaaggeess// Package sources for compiling packages can be obtained by retrieving the file ffttpp::////ffttpp..nneettbbssdd..oorrgg//ppuubb//NNeettBBSSDD//NNeettBBSSDD-- ccuurrrreenntt//ttaarr__ffiilleess//ppkkggssrrcc..ttaarr..ggzz and extracting it into _/_u_s_r_/_p_k_g_s_r_c. See _/_u_s_r_/_p_k_g_s_r_c_/_R_E_A_D_M_E then for more information. 6. Misc ++oo To adjust the system to your local timezone, point the _/_e_t_c_/_l_o_c_a_l_t_i_m_e symlink to the appropriate file under _/_u_s_r_/_s_h_a_r_e_/_z_o_n_e_i_n_f_o. ++oo Edit _/_e_t_c_/_a_l_i_a_s_e_s to forward root mail to the right place (run newaliases(1) afterwards.) ++oo The _/_e_t_c_/_s_e_n_d_m_a_i_l_._c_f file will almost definitely need to be ad- justed; files aiding in this can be found in _/_u_s_r_/_s_h_a_r_e_/_s_e_n_d_m_a_i_l. See the README file there for more infor- mation. ++oo Edit _/_e_t_c_/_r_c_._l_o_c_a_l to run any local daemons you use. ++oo Many of the _/_e_t_c files are documented in section 5 of the manu- al; so just invoking mmaann _f_i_l_e_n_a_m_e is likely to give you more information on these files. UUppggrraaddiinngg aa pprreevviioouussllyy--iinnssttaalllleedd NNeettBBSSDD SSyysstteemm Before updating, you probably would want to backup your original filesys- tems! The update procedure will not overwrite or remove any files not present in the sets you install. If you've replaced programs present in the dis- tribution, you have to replace them again after you did the update. The etc-set needs special caution. You generally don't want to install this one when upgrading. It is recommended that you get a copy of this set and _carefully_ upgrade your configuration files by hand. 1. Starting the upgrade Ok, let's go. Insert the bootfloppy and follow the 'normal' instal- lation procedure until it asks you if you wish to install or up- grade. At this time, select upgrade. You will now be greeted and reminded of the fact that this is a potential dangerous procedure and that you should not upgrade the etc-set. 2. Selecting your root disk When you decide to proceed, you will be prompted to enter your root disk. After you've done this, it will be checked automatically to make sure that the filesystem is in a sane state before making any modifications. After this is done, you will be asked if you want to configure your network. You can skip this section on NetBSD/Atari for now. 3. Editing the fstab You are now allowed to edit your fstab. Normally you don't have to. Note that the upgrade-kit uses it's own copy of the fstab. Whatever you do here *won't* affect your actual fstab. After you are satis- fied with your fstab, the upgrade-kit will check all filesystems mentioned in it. When they're ok, they will be mounted. 4. The actual upgrade You will now be asked if your sets are stored on a normally mounted filesystem. You should answer 'y' to this question if you have the sets stored on a filesystem that was present in the fstab. The ac- tions you should take for the set extraction are pretty logical (I think). You might want to read the notes in section 9 (Installing the distribution sets) of the installation section. 5. Finishing up After you have extracted the sets, the upgrade kit will proceed with setting the timezone and installing the kernel and bootcode. This is all exactly the same as described in the installation section. CCoommppaattiibbiilliittyy IIssssuueess WWiitthh PPrreevviioouuss NNeettBBSSDD RReelleeaasseess Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 1.4.2 _N_o_t_e Only issues effecting an upgrade from NetBSD 1.3 or NetBSD 1.3.x are decribed here. ++oo "machine" directory/link in "/usr/include" Description Some architecture may fail to install the ccoommpp set because the /usr/include/machine directory changed to a symbolic link in NetBSD 1.4. Fix If this happens, you can use the command # rrmm --rr //uussrr//iinncclluuddee//mmaacchhiinnee to remove the old directory and it contents and reinstall the ccoommpp set. UUssiinngg oonnlliinnee NNeettBBSSDD ddooccuummeennttaattiioonn Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by ``name(section)''. Some examples of this are ++oo intro(1), ++oo man(1), ++oo apropros(1), ++oo passwd(1), and ++oo passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The _m_a_n command is used to view the documentation on a topic, and is started by entering mmaann [_s_e_c_t_i_o_n] _t_o_p_i_c. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is op- tional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter mmaann ppaasssswwdd to read the documentation for passwd(1). To view the documentation for passwd(5)m enter mmaann 55 ppaasssswwdd instead. If you are unsure of what man page you are looking for, enter aapprrooppooss _s_u_b_j_e_c_t_-_w_o_r_d where _s_u_b_j_e_c_t_-_w_o_r_d is your topic of interest; a list of possibly related man pages will be displayed. AAddmmiinniissttrriivviiaa If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at _m_a_j_o_r_d_o_m_o_@_N_e_t_B_S_D_._O_R_G. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: _n_e_t_b_s_d_- _c_o_m_m_e_n_t_s_@_N_e_t_B_S_D_._O_R_G. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports in- clude lots of details. Additionally, bug reports can be sent by mail to: _n_e_t_b_s_d_-_b_u_g_s_@_N_e_t_B_S_D_._O_R_G. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses. If you're inter- ested in doing a serious amount of work on a specific port, you probably should contact the "owner" of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: _n_e_t_b_s_d_-_h_e_l_p_@_N_e_t_B_S_D_._O_R_G. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP some- where, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. TThhaannkkss ggoo ttoo ++oo The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encouragement. ++oo Also, our thanks go to: Mike Hibler Rick Macklem Jan-Simon Pendry Chris Torek for answering lots of questions, fixing bugs, and doing the various work they've done. ++oo UC Berkeley's Experimental Computing Facility provided a home for sun-lamp in the past, people to look after it, and a sense of humor. Rob Robertson, too, has added his unique sense of humor to things, and for a long time provided the primary FTP site for NetBSD. ++oo Vixie Enterprises for hosting the NetBSD FTP, WWW and SUP server. ++oo Redback Networks, Inc. for hosting the NetBSD Mail server. ++oo Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. ++oo Dave Burgess _b_u_r_g_e_s_s_@_c_y_n_j_u_t_._i_n_f_o_n_e_t_._n_e_t has been maintaining the 386BSD/NetBSD/FreeBSD FAQ for quite some time, and deserves to be recognized for it. ++oo The following individuals and organiztions (each in alphabetical or- der) have made donations or loans of hardware and/or money, to sup- port NetBSD development, and deserve credit for it: Steve Allen Jason Birnschein Mason Loring Bliss Jason Brazile Mark Brinicombe David Brownlee Simon Burge Dave Burgess Ralph Campbell Brian Carlstrom James Chacon Bill Coldwell Charles Conn Tom Coulter Charles D. Cranor Christopher G. Demetriou Scott Ellis Hubert Feyrer Castor Fu Greg Gingerich William Gnadt Michael Graff Guenther Grau Ross Harvey Charles M. Hannum Michael L. Hitch Kenneth Alan Hornstein Jordan K. Hubbard Soren Jorvang Scott Kaplan Noah M. Keiserman John Kohl Chris Legrow Ted Lemon Neil J. McRae Perry E. Metzger Herb Peyerl Mike Price Dave Rand Michael Richardson Heiko W. Rupp Brad Salai Chuck Silvers Thor Lancelot Simon Bill Sommerfeld Paul Southworth Ted Spradley Kimmo Suominen Jason R. Thorpe Steve Wadlow Krister Walfridsson Jim Wise Christos Zoulas AboveNet Communications, Inc. Advanced System Products, Inc. Avalon Computer Systems Bay Area Internet Solutions Brains Corporation, Japan Canada Connect Corporation Co-operative Research Centre for Enterprise Distributed Systems Technology Demon Internet, UK Digital Equipment Corporation Easynet, UK Free Hardware Foundation Innovation Development Enterprises of America Internet Software Consortium MS Macro System GmbH, Germany Numerical Aerospace Simulation Facility, NASA Ames Research Center Piermont Information Systems Inc. VMC Harald Frank, Germany Warped Communications, Inc. (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) ++oo Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to mentioned, tell us!) WWee aarree...... (in alphabetical order) _T_h_e _N_e_t_B_S_D _c_o_r_e _g_r_o_u_p_: Alistair Crooks _a_g_c_@_N_e_t_B_S_D_._O_R_G Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._O_R_G Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._O_R_G Luke Mewburn _l_u_k_e_m_@_N_e_t_B_S_D_._O_R_G Christos Zoulas _c_h_r_i_s_t_o_s_@_N_e_t_B_S_D_._O_R_G _T_h_e _p_o_r_t_m_a_s_t_e_r_s _(_a_n_d _t_h_e_i_r _p_o_r_t_s_)_: Mark Brinicombe _m_a_r_k_@_N_e_t_B_S_D_._O_R_G aarrmm3322 Jeremy Cooper _j_e_r_e_m_y_@_N_e_t_B_S_D_._O_R_G ssuunn33xx Ross Harvey _r_o_s_s_@_N_e_t_B_S_D_._O_R_G aallpphhaa Ignatios Souvatzis _i_s_@_N_e_t_B_S_D_._O_R_G aammiiggaa Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._O_R_G sshh33 Eduardo Horvath _e_e_h_@_N_e_t_B_S_D_._O_R_G ssppaarrcc6644 Paul Kranenburg _p_k_@_N_e_t_B_S_D_._O_R_G ssppaarrcc Anders Magnusson _r_a_g_g_e_@_N_e_t_B_S_D_._O_R_G vvaaxx Tsubai Masanari _t_s_u_b_a_i_@_N_e_t_B_S_D_._O_R_G mmaaccppppcc Tsubai Masanari _t_s_u_b_a_i_@_N_e_t_B_S_D_._O_R_G nneewwssmmiippss Minoura Makoto _m_i_n_o_u_r_a_@_N_e_t_B_S_D_._O_R_G xx6688kk Phil Nelson _p_h_i_l_@_N_e_t_B_S_D_._O_R_G ppcc553322 Scott Reynolds _s_c_o_t_t_r_@_N_e_t_B_S_D_._O_R_G mmaacc6688kk Darrin Jewell _d_b_j_@_N_e_t_B_S_D_._O_R_G nneexxtt6688kk Kazuki Sakamoto _s_a_k_a_m_o_t_o_@_N_e_t_B_S_D_._O_R_G bbeebbooxx Wolfgang Solfrank _w_s_@_N_e_t_B_S_D_._O_R_G ooffppppcc Jonathan Stone _j_o_n_a_t_h_a_n_@_N_e_t_B_S_D_._O_R_G ppmmaaxx Shin Takemura _t_a_k_e_m_u_r_a_@_N_e_t_B_S_D_._O_R_G hhppccmmiippss Jason Thorpe _t_h_o_r_p_e_j_@_N_e_t_B_S_D_._O_R_G hhpp330000 Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._O_R_G ii338866 Leo Weppelman _l_e_o_@_N_e_t_B_S_D_._O_R_G aattaarrii Nathan Williams _n_a_t_h_a_n_w_@_N_e_t_B_S_D_._O_R_G ssuunn33 Steve Woodford _s_c_w_@_N_e_t_B_S_D_._O_R_G mmvvmmee6688kk _T_h_e _N_e_t_B_S_D _1_._4_._2 _R_e_l_e_a_s_e _E_n_g_i_n_e_e_r_i_n_g _t_e_a_m_: Chris G. Demetriou _c_g_d_@_N_e_t_B_S_D_._O_R_G Havard Eidnes _h_e_@_N_e_t_B_S_D_._O_R_G Ted Lemon _m_e_l_l_o_n_@_N_e_t_B_S_D_._O_R_G Perry Metzger _p_e_r_r_y_@_N_e_t_B_S_D_._O_R_G Curt Sampson _c_j_s_@_N_e_t_B_S_D_._O_R_G _D_e_v_e_l_o_p_e_r_s _a_n_d _o_t_h_e_r _c_o_n_t_r_i_b_u_t_o_r_s_: Steve Allen _w_o_r_m_e_y_@_N_e_t_B_S_D_._O_R_G Julian Assange _p_r_o_f_f_@_N_e_t_B_S_D_._O_R_G Lennart Augustsson _a_u_g_u_s_t_s_s_@_N_e_t_B_S_D_._O_R_G Christoph Badura _b_a_d_@_N_e_t_B_S_D_._O_R_G Robert V. Baron _r_v_b_@_N_e_t_B_S_D_._O_R_G Erik Berls _c_y_b_e_r_@_N_e_t_B_S_D_._O_R_G John Birrell _j_b_@_N_e_t_B_S_D_._O_R_G Mason Loring Bliss _m_a_s_o_n_@_N_e_t_B_S_D_._O_R_G Manuel Bouyer _b_o_u_y_e_r_@_N_e_t_B_S_D_._O_R_G John Brezak _b_r_e_z_a_k_@_N_e_t_B_S_D_._O_R_G Allen Briggs _b_r_i_g_g_s_@_N_e_t_B_S_D_._O_R_G Aaron Brown _a_b_r_o_w_n_@_N_e_t_B_S_D_._O_R_G David Brownlee _a_b_s_@_N_e_t_B_S_D_._O_R_G Frederick Bruckman _f_r_e_d_b_@_N_e_t_B_S_D_._O_R_G Jon Buller _j_o_n_b_@_N_e_t_B_S_D_._O_R_G Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._O_R_G Dave Burgess _b_u_r_g_e_s_s_@_c_y_n_j_u_t_._i_n_f_o_n_e_t_._n_e_t Robert Byrnes _b_y_r_n_e_s_@_N_e_t_B_S_D_._o_r_g D'Arcy J.M. Cain _d_a_r_c_y_@_N_e_t_B_S_D_._O_R_G Dave Carrel _c_a_r_r_e_l_@_N_e_t_B_S_D_._O_R_G Bill Coldwell _b_i_l_l_c_@_N_e_t_B_S_D_._O_R_G Julian Coleman _j_d_c_@_N_e_t_B_S_D_._O_R_G Chuck Cranor _c_h_u_c_k_@_N_e_t_B_S_D_._O_R_G Aidan Cully _a_i_d_a_n_@_N_e_t_B_S_D_._O_R_G Johan Danielsson _j_o_d_a_@_N_e_t_B_S_D_._O_R_G Matt DeBergalis _d_e_b_e_r_g_@_N_e_t_B_S_D_._O_R_G Rob Deker _d_e_k_e_r_@_N_e_t_B_S_D_._O_R_G Chris G. Demetriou _c_g_d_@_N_e_t_B_S_D_._O_R_G Jaromir Dolecek _j_d_o_l_e_c_e_k_@_N_e_t_B_S_D_._O_R_G Andy Doran _a_d_@_N_e_t_B_S_D_._O_R_G Roland Dowdeswell _e_l_r_i_c_@_N_e_t_B_S_D_._O_R_G Matthias Drochner _d_r_o_c_h_n_e_r_@_N_e_t_B_S_D_._O_R_G Jun Ebihara _j_u_n_@_N_e_t_B_S_D_._O_R_G Havard Eidnes _h_e_@_N_e_t_B_S_D_._O_R_G Enami Tsugutomo _e_n_a_m_i_@_N_e_t_B_S_D_._O_R_G Bernd Ernesti _v_e_e_g_o_@_N_e_t_B_S_D_._O_R_G Erik Fair _f_a_i_r_@_N_e_t_B_S_D_._O_R_G Hubert Feyrer _h_u_b_e_r_t_f_@_N_e_t_B_S_D_._O_R_G Thorsten Frueauf _f_r_u_e_a_u_f_@_N_e_t_B_S_D_._O_R_G Castor Fu _c_a_s_t_o_r_@_N_e_t_B_S_D_._O_R_G Brian R. Gaeke _b_r_g_@_d_g_a_t_e_._o_r_g Thomas Gerner _t_h_o_m_a_s_@_N_e_t_B_S_D_._O_R_G Simon J. Gerraty _s_j_g_@_N_e_t_B_S_D_._O_R_G Justin Gibbs _g_i_b_b_s_@_N_e_t_B_S_D_._O_R_G Adam Glass _g_l_a_s_s_@_N_e_t_B_S_D_._O_R_G Michael Graff _e_x_p_l_o_r_e_r_@_N_e_t_B_S_D_._O_R_G Brian C. Grayson _b_g_r_a_y_s_o_n_@_N_e_t_B_S_D_._O_R_G Brad Grantham _g_r_a_n_t_h_a_m_@_t_e_n_o_n_._c_o_m Matthew Green _m_r_g_@_N_e_t_B_S_D_._O_R_G Juergen Hannken-Illjes _h_a_n_n_k_e_n_@_N_e_t_B_S_D_._O_R_G Charles M. Hannum _m_y_c_r_o_f_t_@_N_e_t_B_S_D_._O_R_G Eric Haszlakiewicz _e_r_h_@_N_e_t_B_S_D_._O_R_G HAYAKAWA Koichi _h_a_y_a_@_N_e_t_B_S_D_._O_R_G Rene Hexel _r_h_@_N_e_t_B_S_D_._O_R_G Michael L. Hitch _m_h_i_t_c_h_@_N_e_t_B_S_D_._O_R_G Christian E. Hopps _c_h_o_p_p_s_@_N_e_t_B_S_D_._O_R_G Ken Hornstein _k_e_n_h_@_N_e_t_B_S_D_._O_R_G Marc Horowitz _m_a_r_c_@_N_e_t_B_S_D_._O_R_G Dean Huxley _d_e_a_n_@_n_e_t_b_s_d_._o_r_g ITOH Yasufumi _i_t_o_h_y_@_N_e_t_B_S_D_._O_R_G Matthew Jacob _m_j_a_c_o_b_@_N_e_t_B_S_D_._O_R_G Lonhyn T. Jasinskyj _l_o_n_h_y_n_@_N_e_t_B_S_D_._O_R_G Chris Jones _c_j_o_n_e_s_@_N_e_t_B_S_D_._O_R_G Soren Jorvang _s_o_r_e_n_@_N_e_t_B_S_D_._O_R_G Antti Kantee _p_o_o_k_a_@_N_e_t_B_S_D_._O_R_G Lawrence Kesteloot _k_e_s_t_e_l_o_o_@_c_s_._u_n_c_._e_d_u Thomas Klausner _w_i_z_@_N_e_t_B_S_D_._O_R_G Klaus Klein _k_l_e_i_n_k_@_N_e_t_B_S_D_._O_R_G John Kohl _j_t_k_@_N_e_t_B_S_D_._O_R_G Kevin Lahey _k_m_l_@_N_e_t_B_S_D_._O_R_G Johnny C. Lam _j_l_a_m_@_N_e_t_B_S_D_._O_R_G Martin J. Laubach _m_j_l_@_N_e_t_B_S_D_._O_R_G Ted Lemon _m_e_l_l_o_n_@_N_e_t_B_S_D_._O_R_G Joel Lindholm _j_o_e_l_@_N_e_t_B_S_D_._O_R_G Mike Long _m_i_k_e_l_@_N_e_t_B_S_D_._O_R_G Warner Losh _i_m_p_@_N_e_t_B_S_D_._O_R_G Brett Lymn _b_l_y_m_n_@_N_e_t_B_S_D_._O_R_G Paul Mackerras _p_a_u_l_u_s_@_N_e_t_B_S_D_._O_R_G Dan McMahill _d_m_c_m_a_h_i_l_l_@_N_e_t_B_S_D_._O_R_G Neil J. McRae _n_e_i_l_@_N_e_t_B_S_D_._O_R_G Perry Metzger _p_e_r_r_y_@_N_e_t_B_S_D_._O_R_G der Mouse _m_o_u_s_e_@_N_e_t_B_S_D_._O_R_G Joseph Myers _j_s_m_@_N_e_t_B_S_D_._O_R_G Ken Nakata _k_e_n_n_@_N_e_t_B_S_D_._O_R_G Bob Nestor _r_n_e_s_t_o_r_@_N_e_t_B_S_D_._O_R_G Tohru Nishimura _n_i_s_i_m_u_r_a_@_N_e_t_B_S_D_._O_R_G Masaru Oki _o_k_i_@_N_e_t_B_S_D_._O_R_G Greg Oster _o_s_t_e_r_@_N_e_t_B_S_D_._O_R_G Herb Peyerl _h_p_e_y_e_r_l_@_N_e_t_B_S_D_._O_R_G Matthias Pfaller _m_a_t_t_h_i_a_s_@_N_e_t_B_S_D_._O_R_G Dante Profeta _d_a_n_t_e_@_N_e_t_B_S_D_._O_R_G Chris Provenzano _p_r_o_v_e_n_@_N_e_t_B_S_D_._O_R_G Waldi Ravens _w_a_l_d_i_@_m_o_a_c_s_._i_n_d_i_v_._n_l_._n_e_t Darren Reed _d_a_r_r_e_n_r_@_N_e_t_B_S_D_._O_R_G Michael Richardson _m_c_r_@_N_e_t_B_S_D_._O_R_G Tim Rightnour _g_a_r_b_l_e_d_@_N_e_t_B_S_D_._O_R_G Gordon Ross _g_w_r_@_N_e_t_B_S_D_._O_R_G Heiko W. Rupp _h_w_r_@_N_e_t_B_S_D_._O_R_G SAITOH Masanobu _m_s_a_i_t_o_h_@_N_e_t_B_S_D_._O_R_G Curt Sampson _c_j_s_@_N_e_t_B_S_D_._O_R_G Wilfredo Sanchez _w_s_a_n_c_h_e_z_@_N_e_t_B_S_D_._O_R_G Ty Sarna _t_s_a_r_n_a_@_N_e_t_B_S_D_._O_R_G SATO Kazumi _s_a_t_o_@_N_e_t_B_S_D_._O_R_G Matthias Scheler _t_r_o_n_@_N_e_t_B_S_D_._O_R_G Karl Schilke (rAT) _r_a_t_@_N_e_t_B_S_D_._O_R_G Konrad Schroder _p_e_r_s_e_a_n_t_@_N_e_t_B_S_D_._O_R_G Tim Shepard _s_h_e_p_@_N_e_t_B_S_D_._O_R_G Takao Shinohara _s_h_i_n_@_N_e_t_B_S_D_._O_R_G Chuck Silvers _c_h_s_@_N_e_t_B_S_D_._O_R_G Thor Lancelot Simon _t_l_s_@_N_e_t_B_S_D_._O_R_G Noriyuki Soda _s_o_d_a_@_N_e_t_B_S_D_._O_R_G Bill Sommerfeld _s_o_m_m_e_r_f_e_l_d_@_N_e_t_B_S_D_._O_R_G Bill Studenmund _w_r_s_t_u_d_e_n_@_N_e_t_B_S_D_._O_R_G Kevin Sullivan _s_u_l_l_i_v_a_n_@_N_e_t_B_S_D_._O_R_G Kimmo Suominen _k_i_m_@_N_e_t_B_S_D_._O_R_G Matt Thomas _m_a_t_t_@_N_e_t_B_S_D_._O_R_G Christoph Toshok _t_o_s_h_o_k_@_N_e_t_B_S_D_._O_R_G Izumi Tsutsui _t_s_u_t_s_u_i_@_N_e_t_B_S_D_._O_R_G UCHIYAMA Yasushi _u_c_h_@_N_e_t_B_S_D_._O_R_G Todd Vierling _t_v_@_N_e_t_B_S_D_._O_R_G Aymeric Vincent _a_y_m_e_r_i_c_@_N_e_t_B_S_D_._O_R_G Paul Vixie _v_i_x_i_e_@_N_e_t_B_S_D_._O_R_G Krister Walfridsson _k_r_i_s_t_e_r_w_@_N_e_t_B_S_D_._O_R_G Lex Wennmacher _w_e_n_n_m_a_c_h_@_N_e_t_B_S_D_._O_R_G Assar Westerlund _a_s_s_a_r_@_N_e_t_B_S_D_._O_R_G Rob Windsor _w_i_n_d_s_o_r_@_N_e_t_B_S_D_._O_R_G Dan Winship _d_a_n_w_@_N_e_t_B_S_D_._O_R_G Jim Wise _j_w_i_s_e_@_N_e_t_B_S_D_._O_R_G Colin Wood _e_n_d_e_r_@_N_e_t_B_S_D_._O_R_G LLeeggaall MMuummbboo--JJuummbboo The following notices are required to satisfy the license terms of the software that we have mentioned in this document: This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes software developed by Adam Glass and Charles Han- num. This product includes software developed by Adam Glass. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Charles D. Cranor and Wash- ington University. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum, by the Uni- versity of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum. This product includes software developed by Chris Provenzano. This product includes software developed by Christian E. Hopps. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by David Jones and Gordon Ross. This product includes software developed by Dean Huxley. This product includes software developed by Eric S. Hvozda. This product includes software developed by Ezra Story. This product includes software developed by Gordon Ross. This product includes software developed by Gordon W. Ross and Leo Wep- pelman. This product includes software developed by Gordon W. Ross. This product includes software developed by Herb Peyerl. This product includes software developed by Ian W. Dall. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/. This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by John Polstra. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Julian Highfield. This product includes software developed by Kenneth Stailey. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Mark Brinicombe. This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Solfrank. This product includes software developed by Mats O Jansson and Charles D. Cranor. This product includes software developed by Mats O Jansson. This product includes software developed by Matthias Pfaller. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Peter Galbavy. This product includes software developed by Philip A. Nelson. This product includes software developed by Rodney W. Grimes. This product includes software developed by Scott Bartram. This product includes software developed by SigmaSoft, Th. Lockert. This product includes software developed by Terrence R. Lambert. This product includes software developed by Theo de Raadt and John Brezak. This product includes software developed by Theo de Raadt. This product includes software developed by TooLs GmbH. This product includes software developed by Winning Strategies, Inc. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the University of Calgary De- partment of Computer Science and its contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed for the FreeBSD project. This product includes software developed for the Internet Software Con- sortium by Ted Lemon. This product includes software developed for the NetBSD Project by Frank van der Linden. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Matthieu Herrb. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by Ted Lemon. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Niklas Hallqvist, C Stone and Job de Haas. This product includes software developed by Gordon Ross This product includes software developed by Leo Weppelman. This product includes software developed by Markus Wild. This product includes software developed by Thomas Gerner This product includes software developed by Waldi Ravens. NetBSD 23 March 1999 28