INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NNAAMMEE IINNSSTTAALLLL - Installation procedure for NetBSD/evbppc. CCOONNTTEENNTTSS About this Document............................................2 What is NetBSD?................................................2 Changes Between The NetBSD 1.6 and 2.0 Releases................3 Kernel......................................................3 Networking..................................................3 File system.................................................4 Security....................................................4 System administration and user tools........................4 Miscellaneous...............................................4 evbppc specific.............................................5 Important notes about NetBSD 2.0...............................5 The Future of NetBSD...........................................5 Sources of NetBSD..............................................6 NetBSD 2.0 Release Contents....................................6 NetBSD/evbppc subdirectory structure........................7 Binary distribution sets....................................8 NetBSD/evbppc System Requirements and Supported Devices........9 Supported devices...........................................9 Unsupported devices........................................10 Supported boot devices and media...........................10 Getting the NetBSD System on to Useful Media..................10 Preparing your System for NetBSD installation.................13 Booting over a serial line.................................13 Booting from the network...................................13 Installing the NetBSD System..................................17 Booting the installer......................................17 Example of a normal boot...................................17 Common Problems and Error Messages.........................17 Running the sysinst installation program...................17 Introduction............................................17 Possible PCMCIA issues..................................17 General.................................................18 Quick install...........................................18 Booting NetBSD..........................................19 Network configuration...................................19 Installation drive selection and parameters.............19 Partitioning the disk...................................19 Preparing your hard disk................................20 Getting the distribution sets...........................20 Installation using ftp..................................20 Installation using NFS..................................21 Installation from CD-ROM................................21 Installation from an unmounted file system..............21 Installation from a local directory.....................21 Extracting the distribution sets........................21 Finalizing your installation............................22 Post installation steps.......................................22 Upgrading a previously-installed NetBSD System................24 Compatibility Issues With Previous NetBSD Releases............24 Issues affecting an upgrade from NetBSD 1.6................24 Using online NetBSD documentation.............................25 Administrivia.................................................26 Thanks go to..................................................26 We are........................................................28 Legal Mumbo-Jumbo.............................................34 The End.......................................................39 DDEESSCCRRIIPPTTIIOONN AAbboouutt tthhiiss DDooccuummeenntt This document describes the installation procedure for NetBSD 2.0 on the _e_v_b_p_p_c platform. It is available in four different formats titled _I_N_S_T_A_L_L_._e_x_t, where _._e_x_t is one of _._p_s, _._h_t_m_l, _._m_o_r_e, or _._t_x_t: _._p_s PostScript. _._h_t_m_l Standard Internet HTML. _._m_o_r_e The enhanced text format used on UNIX -like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line _m_a_n pages are generally pre- sented. _._t_x_t Plain old ASCII. You are reading the _m_o_r_e version. WWhhaatt iiss NNeettBBSSDD?? The NetBSD Operating System is a fully functional Open Source UNIX -like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on fifty four different system architectures (ports), featuring sev- enteen machine architectures across fifteen distinct CPU families, and is being ported to more. The NetBSD 2.0 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distri- bution. For information on them, please see the NetBSD web site at _._: hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. CChhaannggeess BBeettwweeeenn TThhee NNeettBBSSDD 11..66 aanndd 22..00 RReelleeaasseess The NetBSD 2.0 release provides numerous significant functional enhance- ments, including support for many new devices, integration of hundreds of bug fixes, new and updated kernel subsystems, and many user-land enhance- ments. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize over two years of development that went into the NetBSD 2.0 release. Some highlights include: _K_e_r_n_e_l ++oo Ports to new platforms including: amd64, evbsh5, and xen. ++oo Native thread support has been added, based on Scheduler Activations. Applications which support native threads can now take full advantage of the high-performance NetBSD POSIX threads implementation. ++oo Kernel events notification framework - kqueue kqueue provides a stateful and efficient event notification framework. Currently sup- ported events include socket, file, directory, fifo, pipe, tty and device changes, and monitoring of processes and signals. kqueue is supported by all writable filesystems in the NetBSD tree (with the exception of Coda) and all device drivers supporting poll(2). ++oo Improvements have been made to NetBSD's Linux emulation to support the latest Sun JDK/JRE for Linux. Testing has shown that it now runs as well as it does on Linux natively. ++oo NetBSD 2.0 enforces non-executable mappings on many platforms. This means that parts of the stack and heap are made non-executable when they are marked writable. This makes exploiting potential buffer overflows harder. ++oo For the i386 port it now supports SMP and has a new ACPI and power management framework which takes advantage of Intel's ACPI implemen- tation. ++oo The macppc port also now supports SMP as well as hardware support for newer G4 models has been added. ++oo SMP support has been added to the sparc port as well. ++oo New generic i2c framework, supporting bit-bang and "intelligent" con- trollers. ++oo sysctl(9) was switched from a static binding to a dynamic implementa- tion. ++oo Add a new driver satalink(4) and move SATA support from other con- trollers into this along with adding support for new controllers. _N_e_t_w_o_r_k_i_n_g ++oo ipf(8) has been upgraded to version 4.1.3. ++oo tcp(4) now implements path MTU discovery blackhole detection (i.e. it will turn off path MTU discovery if the connection is losing). ++oo Socket buffer insertion is now O(C). This can provide a substantial performance boost to some applications which use large socket buffers. ++oo wi(4) has support for Host-AP mode, allowing Intersil Prism2/2.5/3-based boards to be used to make an 802.11 Access Point. ++oo Support for ipf(8) has been added to bridge(4) and brconfig(8) ++oo Change port allocation from linked list to a hash table for better performance. _F_i_l_e _s_y_s_t_e_m ++oo FreeBSD's UFS2 has been ported to NetBSD. UFS2 is an extension to FFS, adding 64 bit block pointers and support for extended file stor- age. Among other enhancements, UFS2 allows for file systems larger than 1Terabyte. ++oo The cryptographic disk driver (cgd) can be used to encrypt disks or partitions, using some strong encryption algorithms, like AES (Rijn- dael) and Blowfish. cgd can also be configured to encrypt swap. _S_e_c_u_r_i_t_y ++oo The systrace utility has been added to the system. systrace monitors and controls an application access to the system by enforcing access policies for system calls. The systrace utility might be used to trace an untrusted application's access to the system. In addition, it can be used to protect the system from software bugs (such as buffer overflows) by constraining a daemon's access to the system. The privilege elevation feature of systrace can be used to obviate the need to run large, untrusted programs as root when only one or two system calls require the elevated privilege. ++oo Verified Exec support has been added in this release. Verified Exec verifies a cryptographic hash before allowing execution of binaries and scripts. This can be used to prevent a system from running bina- ries or scripts which have been illegally modified or installed. In addition, Verified Exec can also be used to limit the use of script interpreters to authorized scripts only and disallow interactive use. _S_y_s_t_e_m _a_d_m_i_n_i_s_t_r_a_t_i_o_n _a_n_d _u_s_e_r _t_o_o_l_s ++oo Switched from the GPL version to a non-GPL version of various tools including gzip and awk. _M_i_s_c_e_l_l_a_n_e_o_u_s ++oo NetBSD 2.0 supports a new toolchain based on gcc 3.3.3 and binutils 2.14. gcc 3.3.1 adds support for a number of CPU targets and greatly improved support for i386 and other targets. The support for new platforms in gcc 3.3.3 has enabled the porting of NetBSD to even more architectures. ++oo Updates of most third party packages that are shipped in the base system to the following latest stable releases: -- bind 8.3.7 -- binutils 2.14 -- cvs 1.11.17 -- diffutils 2.8.1 -- file 4.08 -- gcc 3.3.3 -- gdb 5.3 -- grep 2.5.1 -- groff 1.19 -- less 381 -- openssl 0.9.7d -- postfix 2.0.19 -- sendmail 8.12.11 -- tcpump 3.7.1 -- texinfo 4.6 ++oo Many new packages in the _p_k_g_s_r_c system, including the latest open source desktop KDE3, OpenOffice, perl, Apache and many more. A num- ber of new platforms are supported, including Darwin, FreeBSD, IRIX, Linux, OpenBSD and Solaris. Support for various other platforms (among them AIX, BSD/OS and HP-UX) is currently being worked on thanks to our new, portable bootstrap kit which makes it much simpler to port pkgsrc support to new operating systems. At the time of writing, there are over 4500 third party packages available in pkgsrc. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. _e_v_b_p_p_c _s_p_e_c_i_f_i_c This is the first major release of NetBSD/evbppc. IImmppoorrttaanntt nnootteess aabboouutt NNeettBBSSDD 22..00 ++oo As noted above, the sendmail third-party program has been upgraded since the last release. The new version of sendmail runs without requiring being set-user-ID to ``root''. In order to retain the functionality that a newly installed system can send mail ``out of the box'', the default has changed so that sendmail will now start by default, and listen for host-local connec- tions. If this behaviour is not desired, you can either 1. explicitly set the sendmail variable to ``NO'' in _/_e_t_c_/_r_c_._c_o_n_f, 2. modify _/_e_t_c_/_m_a_i_l_/_s_u_b_m_i_t_._c_f to point to another host, 3. modify _/_e_t_c_/_m_a_i_l_e_r_._c_o_n_f to point to something else than send- mail, or 4. make sendmail set-user-ID to ``root'', remove _/_e_t_c_/_m_a_i_l_/_s_u_b_m_i_t_._c_f, and set the sendmail_suid variable to ``YES'' in _/_e_t_c_/_r_c_._c_o_n_f. The latter method is strongly discouraged. TThhee FFuuttuurree ooff NNeettBBSSDD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: ++oo providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. ++oo providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. ++oo providing a better position from which to undertake promotional activities. ++oo periodically organizing workshops for developers and other interested people to discuss ongoing work. We intend to begin narrowing the time delay between releases. Our ambi- tion is to provide a full release every six to eight months. We hope to support even _m_o_r_e hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the usability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. SSoouurrcceess ooff NNeettBBSSDD Refer to _._: hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//SSiitteess//nneett..hhttmmll NNeettBBSSDD 22..00 RReelleeaassee CCoonntteennttss The root directory of the NetBSD 2.0 release is organized as follows: _._._._/_N_e_t_B_S_D_-_2_._0_/ CHANGES Changes since earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 2.0 distribution. README.files README describing the distribution's contents. TODO NetBSD 's todo list (also somewhat incomplete and out of date). _p_a_t_c_h_e_s_/ Post-release source code patches. _s_o_u_r_c_e_/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 2.0 has a binary distribution. The source distribution sets can be found in subdirectories of the _s_o_u_r_c_e subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: ggnnuussrrcc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. _7_9 _M_B _g_z_i_p_p_e_d_, _3_6_7 _M_B _u_n_c_o_m_p_r_e_s_s_e_d ppkkggssrrcc This set contains the ``pkgsrc'' sources, which contain the in- frastructure to build third-party packages. _2_4 _M_B _g_z_i_p_p_e_d_, _2_0_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d sshhaarreessrrcc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. _5 _M_B _g_z_i_p_p_e_d_, _2_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d ssrrcc This set contains all of the base NetBSD 2.0 sources which are not in ggnnuussrrcc, sshhaarreessrrcc, or ssyyssssrrcc. _3_7 _M_B _g_z_i_p_p_e_d_, _1_7_6 _M_B _u_n_c_o_m_p_r_e_s_s_e_d ssyyssssrrcc This set contains the sources to the NetBSD 2.0 kernel for all architectures; config(8); and dbsym(8). _2_6 _M_B _g_z_i_p_p_e_d_, _1_4_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d xxssrrcc This set contains the sources to the X Window System. _8_4 _M_B _g_z_i_p_p_e_d_, _4_5_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d All the above source sets are located in the _s_o_u_r_c_e_/_s_e_t_s subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the ppkkggssrrcc set, which is traditionally unpacked into _/_u_s_r_/_p_k_g_s_r_c, all sets may be unpacked into _/_u_s_r_/_s_r_c with the command: # (( ccdd // ;; ttaarr --zzxxppff -- )) sseett__nnaammee..ttggzz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: BSDSUM Historic BSD checksums for the various files in that directory, in the format produced by the command: cckkssuumm --oo 11 _f_i_l_e. CKSUM POSIX checksums for the various files in that directory, in the format produced by the command: cckkssuumm _f_i_l_e. MD5 MD5 digests for the various files in that directory, in the format produced by the command: cckkssuumm --mm _f_i_l_e. SYSVSUM Historic ATT System V UNIX checksums for the various files in that directory, in the format produced by the command: cckkssuumm --oo 22 _f_i_l_e. The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest pos- sible range of system can check the integrity of the release files. _N_e_t_B_S_D_/_e_v_b_p_p_c _s_u_b_d_i_r_e_c_t_o_r_y _s_t_r_u_c_t_u_r_e The evbppc-specific portion of the NetBSD 2.0 release is found in the _e_v_b_p_p_c subdirectory of the distribution: _._._._/_N_e_t_B_S_D_-_2_._0_/_e_v_b_p_p_c_/. It con- tains the following files and directories: _I_N_S_T_A_L_L_._h_t_m_l _I_N_S_T_A_L_L_._p_s _I_N_S_T_A_L_L_._t_x_t _I_N_S_T_A_L_L_._m_o_r_e Installation notes in various file formats, including this file. The _._m_o_r_e file contains underlined text using the more(1) conventions for indicating italic and bold display. _b_i_n_a_r_y_/ _k_e_r_n_e_l_/ _n_e_t_b_s_d_-_W_A_L_N_U_T_._g_z A gzipped NetBSD kernel (in ELF format) containing code for everything sup- ported in this release. _n_e_t_b_s_d_._i_m_g_-_W_A_L_N_U_T_._g_z Same as the above, but in the format expected by the firmware. _n_e_t_b_s_d_-_I_N_S_T_A_L_L___W_A_L_N_U_T_._g_z A gzipped NetBSD kernel (ELF format) containing code for everything sup- ported in this release. It also includes a RAM-disk installer with ssyyssiinnsstt. _n_e_t_b_s_d_-_I_N_S_T_A_L_L___W_A_L_N_U_T_._i_m_g_._g_z Same as the above, but in the format expected by the firmware. _s_e_t_s_/ evbppc binary distribution sets; see below. _i_n_s_t_a_l_l_a_t_i_o_n_/ _B_i_n_a_r_y _d_i_s_t_r_i_b_u_t_i_o_n _s_e_t_s The NetBSD evbppc binary distribution sets contain the binaries which comprise the NetBSD 2.0 release for the evbppc. The binary distribution sets can be found in the _e_v_b_p_p_c_/_b_i_n_a_r_y_/_s_e_t_s subdirectory of the NetBSD 2.0 distribution tree, and are as follows: bbaassee The NetBSD 2.0 evbppc bbaassee binary distribution. You _m_u_s_t install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally functional. It includes shared library support, and excludes everything described below. _1_8 _M_B _g_z_i_p_p_e_d_, _5_1 _M_B _u_n_c_o_m_p_r_e_s_s_e_d ccoommpp Things needed for compiling programs. This set includes the system include files (_/_u_s_r_/_i_n_c_l_u_d_e) and the various system libraries (except the shared libraries, which are included as part of the bbaassee set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. _2_3 _M_B _g_z_i_p_p_e_d_, _8_3 _M_B _u_n_c_o_m_p_r_e_s_s_e_d eettcc This distribution set contains the system configuration files that reside in _/_e_t_c and in several other places. This set _m_u_s_t be installed if you are installing the system from scratch, but should _n_o_t be used if you are upgrading. _1 _M_B _g_z_i_p_p_e_d_, _1 _M_B _u_n_c_o_m_p_r_e_s_s_e_d ggaammeess This set includes the games and their manual pages. _3 _M_B _g_z_i_p_p_e_d_, _8 _M_B _u_n_c_o_m_p_r_e_s_s_e_d kkeerrnn--WWAALLNNUUTT This set contains a NetBSD/evbppc 2.0 kernel in ELF format named _/_n_e_t_b_s_d and the same kernel in the format needed by the bootloader as _/_n_e_t_b_s_d_._i_m_g. These kernels are specific to the IBM 405GP based Wal- nut evaluation board. You _m_u_s_t install this distribution set. _4 _M_B _g_z_i_p_p_e_d_, _8 _M_B _u_n_c_o_m_p_r_e_s_s_e_d mmaann This set includes all of the manual pages for the binaries and other software contained in the bbaassee set. Note that it does not include any of the manual pages that are included in the other sets. _8 _M_B _g_z_i_p_p_e_d_, _3_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d mmiisscc This set includes the (rather large) system dictionaries, the type- settable document set, and other files from _/_u_s_r_/_s_h_a_r_e. _3 _M_B _g_z_i_p_p_e_d_, _9 _M_B _u_n_c_o_m_p_r_e_s_s_e_d tteexxtt This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. _2 _M_B _g_z_i_p_p_e_d_, _7 _M_B _u_n_c_o_m_p_r_e_s_s_e_d NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 4.4.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xxbbaassee The basic files needed for a complete X client environment. This does not include the X servers. _7 _M_B _g_z_i_p_p_e_d_, _1_9 _M_B _u_n_c_o_m_p_r_e_s_s_e_d xxccoommpp The extra libraries and include files needed to compile X source code. _1_3 _M_B _g_z_i_p_p_e_d_, _4_4 _M_B _u_n_c_o_m_p_r_e_s_s_e_d xxffoonntt Fonts needed by X. _3_1 _M_B _g_z_i_p_p_e_d_, _3_9 _M_B _u_n_c_o_m_p_r_e_s_s_e_d xxeettcc Configuration files for X which could be locally modified. _0_._0_3 _M_B _g_z_i_p_p_e_d_, _0_._1_7 _M_B _u_n_c_o_m_p_r_e_s_s_e_d xxsseerrvveerr The X server. _4 _M_B _g_z_i_p_p_e_d_, _1_0 _M_B _u_n_c_o_m_p_r_e_s_s_e_d The evbppc binary distribution sets are distributed as gzipped tar files named with the extension ..ttggzz, e.g. _b_a_s_e_._t_g_z. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the file- names stored in the sets are relative and therefore the files are extracted _b_e_l_o_w _t_h_e _c_u_r_r_e_n_t _d_i_r_e_c_t_o_r_y. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the ttaarr --xxppff command from the root directory ( _/ ) of your system. This util- ity is used only in a Traditional method installation. _N_o_t_e_: Each directory in the evbppc binary distribution also has its own checksum files, just as the source distribution does. NNeettBBSSDD//eevvbbppppcc SSyysstteemm RReeqquuiirreemmeennttss aanndd SSuuppppoorrtteedd DDeevviicceess NetBSD/evbppc is a port of NetBSD to PowerPC based evaluation board. At the present time, the IBM PowerPC 405GP based walnut evaluation board is the only board supported by this port. As a result, this documentation is specific to installing NetBSD/evbppc on that particular piece of hardware. More evalua- tion boards will be added in due course, and this documentation will be updated accordingly. _S_u_p_p_o_r_t_e_d _d_e_v_i_c_e_s ++oo Ethernet: The built-in Ethernet card is not supported, so another PCI Ethernet card supported by NetBSD must be provided if you want to use NetBSD/evbppc on a network. Any PCI Ethernet card supported by NetBSD should work. ++oo SCSI: Any PCI SCSI card supported by NetBSD should work, as should most SCSI disk/tape/CD-ROM devices. ++oo IDE: -- Promise Ultra66 (_p_c_i_i_d_e) -- Other PCI IDE controllers should work, but there are no reports. -- Most IDE disk/CD-ROM/ATAPI devices should work. ++oo Audio -- PCI audio cards, although none have been tested. ++oo Serial ports -- On-board serial ports (_c_o_m_0) and (_c_o_m_1) -- Some PCI serial ports should work, but no one has tried them ++oo PCI cards -- Most MI PCI cards should work, although very few have been tested with NetBSD/evbppc hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//HHaarrddwwaarree//ppccii..hhttmmll _U_n_s_u_p_p_o_r_t_e_d _d_e_v_i_c_e_s ++oo On-board Ethernet _N_o_t_e: This does not concern booting the kernel itself, since that is done by the firmware. For using an NFS root you will have to pro- vide a supported network card, though. _S_u_p_p_o_r_t_e_d _b_o_o_t _d_e_v_i_c_e_s _a_n_d _m_e_d_i_a The firmware only supports booting from network or the serial port, so you cannot boot from disk even if you install a disk controller. Instructions for booting from serial port are not provided; in the following we will describe how to setup netbooting. The first step is setting the IP addresses of both the walnut itself and the host that will be serving the kernel image. From the main menu, choose 3 to set the IP address of the machine: 1 - Enable/disable tests 2 - Enable/disable boot devices 3 - Change IP addresses 4 - Ping test 5 - Toggle ROM monitor debugger 6 - Toggle automatic menu 7 - Display configuration 8 - Save changes to configuration 9 - Set baud rate for s1 boot A - Enable/disable I cache (Enabled ) B - Enable/disable D cache (Enabled ) 0 - Exit menu and continue -> 3 Set the IP address for the local Ethernet with 1: --- CHANGE IP ADDRESS --- Device List: 001 Enabled Ethernet [ENET] local=0.0.0.0 remote=0.0.0.0 hwaddr=0004ace312bd 004 Disabled Serial Port 2 [S2] local=8.1.1.2 remote=255.255.255.255 hwaddr=ffffffffffff ---------------------------- select device to change ->1 1 - Change local address 2 - Change remote address 0 - Return to main menu ->1 Current IP address = (0.0.0.0) Enter new IP address ->Enter IP address in dot notation, (eg. 8.1.1.2) Here you enter the machine's IP address, e.g. 10.0.0.1. Now you need to do the same thing to set the host IP address (choice 2 from the menu above). Once both the local and remote addresses are set, you can use the ping test to make sure the ethernet is working; or you can simply use option 0, "Exit menu and continue" to try to boot the machine, if you already set up the remote machine to provide a kernel image. For details on how to do that, see the _B_o_o_t_i_n_g _f_r_o_m _t_h_e _n_e_t_w_o_r_k section below. You should now be able to boot the operating system. GGeettttiinngg tthhee NNeettBBSSDD SSyysstteemm oonn ttoo UUsseeffuull MMeeddiiaa Note that if you are installing or upgrading from a writable media, the media can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted. Installation is supported from several media types, including: ++oo CD-ROM / DVD ++oo MS-DOS floppy ++oo FTP ++oo Remote NFS partition ++oo Tape ++oo Existing NetBSD partitions, if performing an upgrade The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the various media are outlined below. _C_D_-_R_O_M _/ _D_V_D Find out where the distribution set files are on the CD-ROM or DVD. Likely locations are _b_i_n_a_r_y_/_s_e_t_s and _e_v_b_p_p_c_/_b_i_n_a_r_y_/_s_e_t_s. Proceed to the instruction on installation. _M_S_-_D_O_S _f_l_o_p_p_y NetBSD doesn't include split sets to keep the distribution size down. They can be created on a seperate machine using the split(1) command, running e.g. sspplliitt --bb 223355kk bbaassee..ttggzz bbaassee.. to split the _b_a_s_e_._t_g_z file from _e_v_b_p_p_c_/_b_i_n_a_r_y_/_s_e_t_s into files named _b_a_s_e_._a_a, _b_a_s_e_._a_b, and so on. Repeat this for all _s_e_t___n_a_m_e_._t_g_z files, splitting them into _s_e_t___n_a_m_e_._x_x files. Count the number of _s_e_t___n_a_m_e_._x_x files that make up the distri- bution sets you want to install or upgrade. You will need one sixth that number of 1.44 MB floppies. Format all of the floppies with MS-DOS. Do _n_o_t make any of them bootable MS-DOS floppies, i.e. don't use format /s to for- mat them. (If the floppies are bootable, then the MS-DOS sys- tem files that make them bootable will take up some space, and you won't be able to fit the distribution set parts on the disks.) If you're using floppies that are formatted for MS-DOS by their manufacturers, they probably aren't bootable, and you can use them out of the box. Place all of the _s_e_t___n_a_m_e_._x_x files on the MS-DOS disks. Once you have the files on MS-DOS disks, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. _F_T_P The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. If you don't have access to a functioning nameserver during installation, the IPv4 address of ffttpp..NNeettBBSSDD..oorrgg is 204.152.184.75 and the IPv6 address is 2001:4f8:4:7:2e0:81ff:fe21:6563 (as of June, 2004). Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. _N_o_t_e_: This method of installation is recommended for those familiar with using BSD network configuration and man- agement commands. If you aren't, this documentation should help, but is not intended to be all-encompassing. _N_F_S Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the _/_e_t_c_/_e_x_p_o_r_t_s file on of the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privi- leges on the server.) You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once the NFS server is set up properly and you have the infor- mation mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. _N_o_t_e_: This method of installation is recommended for those already familiar with using BSD network configuration and management commands. If you aren't, this documenta- tion should help, but is not intended to be all-encom- passing. _T_a_p_e To install NetBSD from a tape, you need to make a tape that contains the distribution set files, in `tar' format. If you're making the tape on a UNIX -like system, the easiest way to do so is probably something like: # ttaarr --ccff _t_a_p_e___d_e_v_i_c_e _d_i_s_t___d_i_r_e_c_t_o_r_i_e_s where _t_a_p_e___d_e_v_i_c_e is the name of the tape device that describes the tape drive you're using; possibly _/_d_e_v_/_r_s_t_0, or something similar, but it will vary from system to system. (If you can't figure it out, ask your system administrator.) In the above example, _d_i_s_t___d_i_r_e_c_t_o_r_i_e_s are the distribution sets' directo- ries, for the distribution sets you wish to place on the tape. For instance, to put the mmiisscc,, bbaassee,, and eettcc distributions on tape (in order to do the absolute minimum installation to a new disk), you would do the following: # ccdd ......//NNeettBBSSDD--22..00 # ccdd eevvbbppppcc//bbiinnaarryy # ttaarr --ccff _t_a_p_e___d_e_v_i_c_e mmiisscc eettcc kkeerrnn _N_o_t_e_: You still need to fill in _t_a_p_e___d_e_v_i_c_e in the example. Once you have the files on the tape, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. PPrreeppaarriinngg yyoouurr SSyysstteemm ffoorr NNeettBBSSDD iinnssttaallllaattiioonn When installing NetBSD for your NetBSD/evbppc system, you have two options: Via serial port or via network. The firmware does not support loading the kernel from a disk. _B_o_o_t_i_n_g _o_v_e_r _a _s_e_r_i_a_l _l_i_n_e This is not currently documented or supported. If you would like to attempt this and supply documentation, please do! _B_o_o_t_i_n_g _f_r_o_m _t_h_e _n_e_t_w_o_r_k 1. Introduction To netboot a evbppc, you must configure one or more servers to provide information and files to your evbppc (the `client ).' If you are using NetBSD (any architecture) on your netboot server(s), the information pro- vided here should be sufficient to configure everything. Additionally, you may wish to look at the diskless(8) manual page and the manual pages for each daemon you'll be configuring. If the server(s) are another operating system, you should consult the NetBSD Diskless HOW-TO, which will walk you through the steps necessary to configure the netboot ser- vices on a variety of platforms. hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//DDooccuummeennttaattiioonn//nneettwwoorrkk//nneettbboooott// You may either netboot the installer so you can install onto a locally attached disk, or you may run your system entirely over the network. Briefly, the netboot process involves discovery, kernel and file system stages. In the first stage, the client discovers information about where to find the kernel image. Once the kernel is loaded, it starts execut- ing. For RAM disk kernels, it mounts the RAM disk file system and begins executing the installer from the RAM disk. For normal (non-RAM disk) kernels, the kernel tries to mount the NFS share that had the kernel and starts executing the installation tools or init(8). All evbppc systems use BOOTP for the discovery stage. TFTP is used in the bootstrap phase to download the kernel via the on-board Ethernet card by the firmware. Thus, NetBSD support for the on-board card is not needed in this step. For NFS mounting a file system on the other hand, NetBSD support for the Ethernet card is needed, and the on-board one will not suffice; you have to provide a second Ethernet card supported by NetBSD . We will use `CC:CC:CC:CC:CC:CC' as the MAC address (ethernet hardware address) of your netboot client machine. You should have determined this address in an earlier stage. In this example, we will use `192.168.1.10' as the IP address of your client and `client.test.net' as its name. We will assume you're providing all of your netboot services on one machine called `server.test.net' with the client's files exported from the direc- tory _/_e_x_p_o_r_t_/_c_l_i_e_n_t_/_r_o_o_t. You should, of course, replace all of these with the names, addresses, and paths appropriate to your environment. You should set up each netboot stage in order (i.e. discovery, bootstrap, kernel, and then file system) so that you can test them as you proceed. 2. dhcpd(8) in bootpd(8) compatible mode Put the following lines in your _/_e_t_c_/_d_h_c_p_d_._c_o_n_f (see dhcpd.conf(5) and dhcp-options(5) for more information): ddns-update-style none; # Do not use any dynamic DNS features # allow bootp; # Allow bootp requests, thus the dhcp server # will act as a bootp server. # authoritative; # master DHCP server for this subnet # subnet 192.168.1.0 netmask 255.255.255.0 { # Which network interface to listen on. # The zeros indicate the range of addresses # that are allowed to connect. } group { # Set of parameters common to all clients # in this "group". # option broadcast-address 192.168.1.255; option domain-name "test.net"; option domain-name-servers dns.test.net; option routers router.test.net; option subnet-mask 255.255.255.0; # # An individual client. # host client.test.net { hardware ethernet CC:CC:CC:CC:CC:CC; fixed-address 192.168.1.10; # # Name of the host (if the fixed address # doesn't resolve to a simple name). # option host-name "client"; # # Name of the kernel image to download via tftp. # Note: Plain (ELF) kernels won't work, you # have to use the corresponding *.img file. # filename "netbsd-INSTALL_WALNUT.img" # # Name of the bootloader or kernel # to download via tftp. # # The path on the NFS server. # option root-path "/export/client/root"; # # If your DHCP server is not your NFS server, supply the # address of the NFS server. Since we assume you run everything # on one server, this is not needed. # # next-server server.test.net; } #you may paste another "host" entry here for additional #clients on this network } You will need to make sure that the _d_h_c_p_d_._l_e_a_s_e_s file exists. # ttoouucchh //vvaarr//ddbb//ddhhccppdd..lleeaasseess You will need to start the ddhhccppdd. If it's already running, you will need to restart it to force it to re-read its configuration file. If the server is running NetBSD, you can achieve this with: # //eettcc//rrcc..dd//ddhhccppdd rreessttaarrtt 3. tftpd(8) The default configuration of the TFTP server is to run in a chroot(8) environment in the _/_t_f_t_p_b_o_o_t directory. Thus, the first order of busi- ness is to create this directory: # mmkkddiirr --pp //ttffttppbboooott Next, edit _/_e_t_c_/_i_n_e_t_d_._c_o_n_f and uncomment the line with the TFTP daemon: tftp dgram udp wait root /usr/libexec/tftpd tftpd -l -s /tftpboot Now, restart inetd(8). If the server is running NetBSD, you can achieve this with: # //eettcc//rrcc..dd//iinneettdd rreessttaarrtt Now, you need to copy the kernel for your evbppc machine to _/_t_f_t_p_b_o_o_t. Just to be sure, let's make everything readable. # cchhmmoodd --RR aa++rrXX //ttffttppbboooott Sometimes, the arp(8) table gets messed up, and the TFTP server can't communicate with the client. In this case, it will write a log message (via syslogd(8)) to _/_v_a_r_/_l_o_g_/_m_e_s_s_a_g_e_s saying: `tftpd: write: Host is down'. If this is the case, you may need to force the server to map your client's ethernet address to its IP address: # aarrpp --ss cclliieenntt CCCC::CCCC::CCCC::CCCC::CCCC::CCCC 4. nfsd(8), mountd(8), and rpcbind(8) You can either boot a kernel, or the RAM disk-based installer _b_i_n_a_r_y_/_k_e_r_n_e_l_/_n_e_t_b_s_d_-_I_N_S_T_A_L_L_._i_m_g_._g_z. In the first case you'll also need an NFS-mounted userland. Let's set up the NFS server. Create the direc- tory you are exporting for the netboot client: # mmkkddiirr --pp //eexxppoorrtt//cclliieenntt//rroooott Put the following line in _/_e_t_c_/_e_x_p_o_r_t_s to enable NFS sharing: /export/client/root -maproot=root client.test.net If your server is currently running an NFS server, you only need to restart mountd(8). Otherwise, you need to start rpcbind(8) and nfsd(8). If the server is running NetBSD, you can achieve this with: # //eettcc//rrcc..dd//rrppccbbiinndd ssttaarrtt # //eettcc//rrcc..dd//nnffssdd ssttaarrtt # //eettcc//rrcc..dd//mmoouunnttdd rreessttaarrtt 5. NetBSD kernel and installation tools If you are netbooting the installer, use _b_i_n_a_r_y_/_k_e_r_n_e_l_/_n_e_t_b_s_d_-_I_N_S_T_A_L_L___W_A_L_N_U_T_._i_m_g_._g_z (this has the installation tools in a RAM disk). Also, copy the distribution files to the client's root directory. # ccpp **ttggzz //eexxppoorrtt//cclliieenntt//rroooott # gguunnzziipp nneettbbssdd--IINNSSTTAALLLL..iimmgg..ggzz # mmvv nneettbbssdd--IINNSSTTAALLLL..iimmgg //eexxppoorrtt//cclliieenntt//rroooott//nneettbbssdd If you are running your evbppc diskless, simply use _b_i_n_a_r_y_/_k_e_r_n_e_l_/_n_e_t_b_s_d_._i_m_g_-_W_A_L_N_U_T_._g_z. 6. Client file system You can skip this step if you do not plan to run your client diskless after installation. Otherwise, you need to extract and set up the client's installation of NetBSD. The Diskless HOW-TO describes how to provide better security and save space on the NFS server over the proce- dure listed here. hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//DDooccuummeennttaattiioonn//nneettwwoorrkk//nneettbboooott//nnffss..hhttmmll ++oo Extracting distribution sets # ccdd //eexxppoorrtt//cclliieenntt//rroooott # ttaarr --xxppzzff //ppaatthh//ttoo//ffiilleess//bbaassee..ttggzz # ttaarr --xxppzzff //ppaatthh//ttoo//ffiilleess//eettcc..ttggzz Continue with the other non-essential distribution sets if desired. ++oo Set up swap # mmkkddiirr //eexxppoorrtt//cclliieenntt//rroooott//sswwaapp # dddd iiff==//ddeevv//zzeerroo ooff==//eexxppoorrtt//cclliieenntt//sswwaapp bbss==44kk ccoouunntt==44kk # eecchhoo ''//eexxppoorrtt//cclliieenntt//sswwaapp --mmaapprroooott==rroooott::wwhheeeell cclliieenntt..tteesstt..nneett'' || ccaatt //eettcc//eexxppoorrttss # //eettcc//rrcc..dd//mmoouunnttdd rreessttaarrtt This creates a 16 MB swap file and exports it to the client. ++oo Create device nodes # ccdd //eexxppoorrtt//cclliieenntt//rroooott//ddeevv # ..//MMAAKKEEDDEEVV aallll This procedure only works on NetBSD hosts. ++oo Set up the client's fstab(5) Create a file in _/_e_x_p_o_r_t_/_c_l_i_e_n_t_/_r_o_o_t_/_e_t_c_/_f_s_t_a_b with the following lines: server:/export/client/swap none swap sw,nfsmntpt=/swap server:/export/client/root / nfs rw 0 0 ++oo Set up the client's rc.conf(5) Edit _/_e_x_p_o_r_t_/_c_l_i_e_n_t_/_r_o_o_t_/_e_t_c_/_r_c_._c_o_n_f rc_configured=YES hostname="client" defaultroute="192.168.1.1" nfs_client=YES auto_ifconfig=NO net_interfaces="" Make sure rc does not reconfigure the network device since it will lose its connection to the NFS server with your root file system. ++oo Set up the client's hosts(5) file. Edit _/_e_x_p_o_r_t_/_c_l_i_e_n_t_/_r_o_o_t_/_e_t_c_/_h_o_s_t_s ::1 localhost 127.0.0.1 localhost 192.168.1.10 client.test.net client 192.168.1.5 server.test.net server 7. Setting up the server daemons If you want these services to start up every time you boot your server, make sure the following lines are present in your _/_e_t_c_/_r_c_._c_o_n_f: nfs_server=YES # enable server daemons mountd=YES rpcbind=YES rpcbind_flags="-l" # -l logs libwrap Also, you'll need to make sure the _t_f_t_p_d line in _/_e_t_c_/_i_n_e_t_d_._c_o_n_f remains uncommented. IInnssttaalllliinngg tthhee NNeettBBSSDD SSyysstteemm _B_o_o_t_i_n_g _t_h_e _i_n_s_t_a_l_l_e_r The kernel starts automatically once it is loaded. _E_x_a_m_p_l_e _o_f _a _n_o_r_m_a_l _b_o_o_t If you already configured the network settings, just press `0' from the boot menu to boot. _C_o_m_m_o_n _P_r_o_b_l_e_m_s _a_n_d _E_r_r_o_r _M_e_s_s_a_g_e_s Do not use the plain ELF kernel as the file provided to the firmware, use the ``netbsd.img'' file (which is in the format the firmware expects). Of course, you should put the matching ``netbsd'' as _/_n_e_t_b_s_d on your root file system, otherwise some kernel grovellers won't work. _R_u_n_n_i_n_g _t_h_e _s_y_s_i_n_s_t _i_n_s_t_a_l_l_a_t_i_o_n _p_r_o_g_r_a_m 1. _I_n_t_r_o_d_u_c_t_i_o_n Using ssyyssiinnsstt, installing NetBSD is a relatively easy process. You still should read this document and have it in hand when doing the installation process. This document tries to be a good guideline for the installation and as such covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. _P_o_s_s_i_b_l_e PCMCIA _i_s_s_u_e_s Machines with PCMCIA slots may have problems during installation. If you do not have PCMCIA on your machine (PCMCIA is only really used on laptop machines), you can skip this section, and ignore the ``[PCMCIA]'' notes. If you do have PCMCIA in your machine, you can safely ignore this section and the ``[PCMCIA]'' the first time, as you are likely to not have prob- lems. Should troubles occur during floppy boot, they may be PCMCIA spe- cific. You should then re-read this section and try again, following the instructions in the ``[PCMCIA]'' notes. This section explains how to work around the installation problem. The kernel keeps careful track of what interrupts and I/O ports are in use during autoconfiguration. It then allows the PCMCIA devices to pick unused interrupts and I/O ports. Unfortunately, the INSTALL kernel may not detect all devices in your system. This may be because the INSTALL kernel only supports the minimum set of devices to install NetBSD on your system, or it may be that NetBSD does not have support for the device causing the conflict. For example, suppose your laptop has a soundblaster device built in; the INSTALL kernel has no sound support. The PCMCIA code might allocate your soundblaster's IRQ and I/O ports to PCMCIA devices, causing them not to work, or to lock up the system. This is especially bad if one of the devices in question is your ethernet card. The kernel attempts to probe for available interrupts that are usable by the PCIC (PCMCIA interrupt controller), which should alleviate interrupt conflicts; however, I/O port conflicts are still possible. This problem will impact some, but not all, users of PCMCIA. If this problem is affecting you, watch the ``[PCMCIA]'' notes that will appear in this document. 3. _G_e_n_e_r_a_l The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. ssyyssiinnsstt is a menu driven installa- tion system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the _/_s_y_s_i_n_s_t program from the command prompt. It is not neces- sary to reboot. 4. _Q_u_i_c_k _i_n_s_t_a_l_l First, let's describe a quick install. The other sections of this docu- ment go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instructions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. ++oo What you need. -- The distribution sets (in this example, they are on CD). -- Some form of bootable media, described above. -- A CD-ROM drive (SCSI or ATAPI), a hard disk and a minimum of of memory installed. -- The hard disk should have at least + _n megabytes of space free, where _n is the number of megabytes of main memory in your system. If you wish to install the X Window System as well, you will need at least 120 MB more. ++oo The Quick Installation -- Boot the system as described above. You should be at the ssyyssiinnsstt main menu. .***********************************************. * NetBSD-2.0 Install System * * * *a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * x: Exit Install System * .***********************************************. -- If you wish, you can configure some network settings immediately by choosing the UUttiilliittyy mmeennuu and then CCoonnffiigguurree nneettwwoorrkk. It isn't actually required at this point, but it may be more conve- nient. Go back to the main menu. -- Choose iinnssttaallll. -- You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. -- After your disk has been prepared, choose CCDD--RROOMM as the medium. The default values for the path and device should be ok. -- After all the files have been unpacked, go back to the main menu and select rreebboooott, after you have removed the bootfloppy from the drive. -- NetBSD will now boot. If you haven't already done so in ssyyssiinnsstt, you should log in as root, and set a password for that account. You are also advised to edit the file _/_e_t_c_/_r_c_._c_o_n_f to match your system needs. -- Your installation is now complete. -- For configuring the X window system, if installed, see the files in _/_u_s_r_/_X_1_1_R_6_/_l_i_b_/_X_1_1_/_d_o_c. Further information can be found on hhttttpp::////wwwwww..xxffrreeee8866..oorrgg//. 5. _B_o_o_t_i_n_g _N_e_t_B_S_D [PCMCIA] Unplug your PCMCIA devices, so that they won't be found by NetBSD. You may want to read the boot messages, to notice your disk's name and capacity. Its name will be something like sd0 or wd0 and the geometry will be printed on a line that begins with its name. As mentioned above, you may need your disk's geometry when creating NetBSD 's partitions. You will also need to know the name, to tell ssyyssiinnsstt on which disk to install. The most important thing to know is that wd0 is NetBSD 's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 6. _N_e_t_w_o_r_k _c_o_n_f_i_g_u_r_a_t_i_o_n [PCMCIA] You can skip this section, as you will only get data from floppy in the first part of the install. If you will not use network operation during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the UUttiilliittyy mmeennuu, and select the CCoonnffiigguurree nneettwwoorrkk option. If you only want to temporarily use networking during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response in reply to answers relating to this. 7. _I_n_s_t_a_l_l_a_t_i_o_n _d_r_i_v_e _s_e_l_e_c_t_i_o_n _a_n_d _p_a_r_a_m_e_t_e_r_s To start the installation, select IInnssttaallll NNeettBBSSDD ttoo hhaarrdd ddiisskk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. ssyyssiinnsstt will report a list of disks it finds and ask you for your selection. Depending on how many disks are found, you may get a different message. You should see disk names like sd0 or sd1. 8. _P_a_r_t_i_t_i_o_n_i_n_g _t_h_e _d_i_s_k ++oo Which portion of the disk to use. You will be asked if you want to use the entire disk or only part of the disk. If you decide to use the entire disk for NetBSD, it will be checked if there are already other systems present on the disk, and you will be asked to confirm whether you want to overwrite these. 9. _E_d_i_t_i_n_g _t_h_e _N_e_t_B_S_D _d_i_s_k_l_a_b_e_l The partition table of the NetBSD part of a disk is called a _d_i_s_k_l_a_b_e_l. There are 4 layouts for the NetBSD part of the disk that you can pick from: SSttaannddaarrdd,, SSttaannddaarrdd wwiitthh XX,, CCuussttoomm and UUssee EExxiissttiinngg. The first two use a set of default values (that you can change) suitable for a normal installation, possibly including X. With the CCuussttoomm option you can spec- ify everything yourself. The last option uses the partition info already present on the disk. You will be presented with the current layout of the NetBSD disklabel, and given a chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 44..22BBSSDD. A swap partition has a special type called sswwaapp. Some partitions in the diskla- bel have a fixed purpose. a Root partition (_/) b Swap partition. c The NetBSD portion of the disk. d-p Available for other use. Traditionally, e is the partition mounted on _/_u_s_r, but this is historical practice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it some- thing different, make sure the name is a single word and contains no spe- cial characters. You don't need to remember this name. 10. _P_r_e_p_a_r_i_n_g _y_o_u_r _h_a_r_d _d_i_s_k _Y_o_u _a_r_e _n_o_w _a_t _t_h_e _p_o_i_n_t _o_f _n_o _r_e_t_u_r_n. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to proceed, enter yes at the prompt. The install program will now label your disk and make the file systems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are run- ning. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Oth- erwise, you can continue the installation program after pressing the return key. 11. _G_e_t_t_i_n_g _t_h_e _d_i_s_t_r_i_b_u_t_i_o_n _s_e_t_s The NetBSD distribution consists of a number of _s_e_t_s, that come in the form of gzipped tarfiles. A few sets must be installed for a working system, others are optional. At this point of the installation, you will be presented with a menu which enables you to choose from one of the fol- lowing methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 12. _I_n_s_t_a_l_l_a_t_i_o_n _u_s_i_n_g _f_t_p To be able to install using ftp, you first need to configure your network setup, if you haven't already at the start of the install procedure. ssyyssiinnsstt will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS when answering the questions to configure net- working, you will need to specify an IP address instead of a hostname for the ftp server. ssyyssiinnsstt will proceed to transfer all the default set files from the remote site to your hard disk. 13. _I_n_s_t_a_l_l_a_t_i_o_n _u_s_i_n_g _N_F_S To be able to install using NFS, you first need to configure your network setup, if you haven't already at the start of the install procedure. ssyyssiinnsstt will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e. correctly exported to your machine. If you did not set up DNS when answering the questions to configure net- working, you will need to specify an IP address instead of a hostname for the NFS server. 14. _I_n_s_t_a_l_l_a_t_i_o_n _f_r_o_m _C_D_-_R_O_M When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM player (usually cd0), and the directory name on the CD-ROM where the distribution files are. ssyyssiinnsstt will then check if the files are indeed available in the speci- fied location, and proceed to the actual extraction of the sets. 15. _I_n_s_t_a_l_l_a_t_i_o_n _f_r_o_m _a_n _u_n_m_o_u_n_t_e_d _f_i_l_e _s_y_s_t_e_m In order to install from a local file system, you will need to specify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. ssyyssiinnsstt will then check if it can indeed access the sets at that location. 16. _I_n_s_t_a_l_l_a_t_i_o_n _f_r_o_m _a _l_o_c_a_l _d_i_r_e_c_t_o_r_y This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file system that is already accessible. ssyyssiinnsstt will ask you for the name of this directory. 17. _E_x_t_r_a_c_t_i_n_g _t_h_e _d_i_s_t_r_i_b_u_t_i_o_n _s_e_t_s After the install sets containing the NetBSD distribution have been made available, you can either extract all the sets (a full installation), or only extract sets that you have selected. In the latter case, you will be shown the currently selected sets, and given the opportunity to select the sets you want. Some sets always need to be installed (kkeerrnn,, bbaassee) and eettcc they will not be shown in this selection menu. Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably, especially on machines with slow graphics consoles or serial consoles. After all the files have been extracted, all the necessary device node files will be created. If you have already configured networking, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the network configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can than set a pass- word for the "root" account, to prevent the machine coming up without access restrictions. 18. _F_i_n_a_l_i_z_i_n_g _y_o_u_r _i_n_s_t_a_l_l_a_t_i_o_n Congratulations, you have successfully installed NetBSD 2.0. You can now reboot the machine, and boot NetBSD from hard disk. PPoosstt iinnssttaallllaattiioonn sstteeppss Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state, with the most important ones described below. 1. Configuring _/_e_t_c_/_r_c_._c_o_n_f If you or the installation software haven't done any configuration of _/_e_t_c_/_r_c_._c_o_n_f (ssyyssiinnsstt usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (_/) mounted read-only. When the system asks you to choose a shell, simply press RETURN to get to a _/_b_i_n_/_s_h prompt. If you are asked for a terminal type, respond with vvtt222200 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # ssttttyy eerraassee ''^^hh'' # ssttttyy eerraassee ''^^??'' At this point, you need to configure at least one file in the _/_e_t_c direc- tory. You will need to mount your root file system read/write with: # //ssbbiinn//mmoouunntt --uu --ww // Change to the _/_e_t_c directory and take a look at the _/_e_t_c_/_r_c_._c_o_n_f file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi-user boot can proceed. Default values for the various programs can be found in _/_e_t_c_/_d_e_f_a_u_l_t_s_/_r_c_._c_o_n_f, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). If your _/_u_s_r directory is on a separate partition and you do not know how to use eedd, you will have to mount your _/_u_s_r partition to gain access to eexx or vvii. Do the following: # mmoouunntt //uussrr # eexxppoorrtt TTEERRMM==vvtt222200 If you have _/_v_a_r on a separate partition, you need to repeat that step for it. After that, you can edit _/_e_t_c_/_r_c_._c_o_n_f with vi(1). When you have finished, type eexxiitt at the prompt to leave the single-user shell and con- tinue with the multi-user boot. Other values that need to be set in _/_e_t_c_/_r_c_._c_o_n_f for a networked environ- ment are _h_o_s_t_n_a_m_e and possibly _d_e_f_a_u_l_t_r_o_u_t_e, furthermore add an _i_f_c_o_n_f_i_g___i_n_t for your network interface, along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have _m_y_n_a_m_e_._m_y_._d_o_m in _/_e_t_c_/_h_o_s_t_s: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an _/_e_t_c_/_r_e_s_o_l_v_._c_o_n_f file or (if you are feeling a little more adventurous) run named(8). See resolv.conf(5) or named(8) for more information. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in _/_e_t_c_/_r_c_._c_o_n_f. Other files in _/_e_t_c that may require modification or setting up include _/_e_t_c_/_m_a_i_l_e_r_._c_o_n_f, _/_e_t_c_/_n_s_s_w_i_t_c_h_._c_o_n_f, and _/_e_t_c_/_w_s_c_o_n_s_._c_o_n_f. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in ssyyssiinnsstt, there is no initial password. If you're using the machine in a networked environment, you should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a dif- ferent user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. Unless you have connected an unusual terminal device as the console you can just press RETURN when it prompts for Terminal type? [...]. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit _/_e_t_c_/_p_a_s_s_w_d directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you have installed the X Window System, look at the files in _/_u_s_r_/_X_1_1_R_6_/_l_i_b_/_X_1_1_/_d_o_c for information. Don't forget to add _/_u_s_r_/_X_1_1_R_6_/_b_i_n to your path in your shell's dot file so that you have access to the X binaries. 5. Installing third party packages If you wish to install any of the software freely available for UNIX -like systems you are strongly advised to first check the NetBSD package system. This automatically handles any changes necessary to make the software run on NetBSD, retrieval and installation of any other packages on which the software may depend, and simplifies installation (and dein- stallation), both from source and precompiled binaries. ++oo More information on the package system is at hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//DDooccuummeennttaattiioonn//ssooffttwwaarree//ppaacckkaaggeess..hhttmmll ++oo A list of available packages suitable for browsing is at ffttpp::////ffttpp..NNeettBBSSDD..oorrgg//ppuubb//NNeettBBSSDD//ppaacckkaaggeess//ppkkggssrrcc//RREEAADDMMEE..hhttmmll ++oo Precompiled binaries can be found at _,_: ffttpp::////ffttpp..NNeettBBSSDD..oorrgg//ppuubb//NNeettBBSSDD//ppaacckkaaggeess// usually in the _2_._0_/_e_v_b_p_p_c_/_A_l_l subdir. You can install them with the following commands under sh(1): ## PPKKGG__PPAATTHH==ffttpp::////ffttpp..NNeettBBSSDD..oorrgg//ppuubb//NNeettBBSSDD//ppaacckkaaggeess//22..00//eevvbbppppcc//AAllll ## eexxppoorrtt PPKKGG__PPAATTHH ## ppkkgg__aadddd --vv ttccsshh ## ppkkgg__aadddd --vv bbaasshh ## ppkkgg__aadddd --vv ppeerrll ## ppkkgg__aadddd --vv aappaacchhee ## ppkkgg__aadddd --vv kkddee ## ppkkgg__aadddd --vv mmoozziillllaa ... If you are using csh(1) then replace the first two lines with the following: ## sseetteennvv PPKKGG__PPAATTHH ffttpp::////ffttpp..NNeettBBSSDD..oorrgg//ppuubb//NNeettBBSSDD//ppaacckkaaggeess//22..00//eevvbbppppcc//AAllll ... The above commands will install the Tenex-csh and Bourne Again shell, the perl programming language , Apache web server, KDE desktop envi- ronment and the Mozilla web browser as well as all the packages they depend on. ++oo Package sources for compiling packages on your own can be obtained by retrieving the file ffttpp::////ffttpp..NNeettBBSSDD..oorrgg//ppuubb//NNeettBBSSDD//NNeettBBSSDD--ccuurrrreenntt//ttaarr__ffiilleess//ppkkggssrrcc..ttaarr..ggzz They are typically extracted into _/_u_s_r_/_p_k_g_s_r_c (though other locations work fine), with the commands: # mmkkddiirr //uussrr//ppkkggssrrcc # (( ccdd //uussrr//ppkkggssrrcc ;; ttaarr --zzxxppff -- )) ppkkggssrrcc..ttaarr..ggzz After extracting, see the _R_E_A_D_M_E and _P_a_c_k_a_g_e_s_._t_x_t files in the extraction directory (e.g. _/_u_s_r_/_p_k_g_s_r_c_/_R_E_A_D_M_E) for more information. 6. Misc ++oo Edit _/_e_t_c_/_m_a_i_l_/_a_l_i_a_s_e_s to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. ++oo The _/_e_t_c_/_m_a_i_l_/_s_e_n_d_m_a_i_l_._c_f file will almost definitely need to be adjusted; files aiding in this can be found in _/_u_s_r_/_s_h_a_r_e_/_s_e_n_d_m_a_i_l. See the README file there for more information. If you prefer post- fix as MTA, adjust _/_e_t_c_/_m_a_i_l_e_r_._c_o_n_f. ++oo Edit _/_e_t_c_/_r_c_._l_o_c_a_l to run any local daemons you use. ++oo Many of the _/_e_t_c files are documented in section 5 of the manual; so just invoking # mmaann 55 _f_i_l_e_n_a_m_e is likely to give you more information on these files. UUppggrraaddiinngg aa pprreevviioouussllyy--iinnssttaalllleedd NNeettBBSSDD SSyysstteemm This is the first release of NetBSD/evbppc, and as such, there is no ability to upgrade from a prior release. CCoommppaattiibbiilliittyy IIssssuueess WWiitthh PPrreevviioouuss NNeettBBSSDD RReelleeaasseess Users upgrading from previous versions of NetBSD may wish to bear the follow- ing problems and compatibility issues in mind when upgrading to NetBSD 2.0. _I_s_s_u_e_s _a_f_f_e_c_t_i_n_g _a_n _u_p_g_r_a_d_e _f_r_o_m _N_e_t_B_S_D _1_._6 The following issues can generally be resolved by extracting the eettcc set into a temporary directory and running _p_o_s_t_i_n_s_t_a_l_l: mkdir /tmp/upgrade cd /tmp/upgrade pax -zrpe -f /path/to/etc.tgz ./etc/postinstall -s `pwd` check ./etc/postinstall -s `pwd` fix Issues fixed by _p_o_s_t_i_n_s_t_a_l_l: ++oo Various files in _/_e_t_c need upgrading. These include: -- _/_e_t_c_/_d_e_f_a_u_l_t_s_/_* -- _/_e_t_c_/_m_t_r_e_e_/_* -- _/_e_t_c_/_d_a_i_l_y -- _/_e_t_c_/_w_e_e_k_l_y -- _/_e_t_c_/_m_o_n_t_h_l_y -- _/_e_t_c_/_s_e_c_u_r_i_t_y -- _/_e_t_c_/_r_c_._s_u_b_r -- _/_e_t_c_/_r_c -- _/_e_t_c_/_r_c_._s_h_u_t_d_o_w_n -- _/_e_t_c_/_r_c_._d_/_* ++oo The following files are now obsolete: _/_e_t_c_/_r_c_._d_/_f_s_c_k_._s_h _/_e_t_c_/_r_c_._d_/_g_a_t_e_d _/_e_t_c_/_r_c_._d_/_k_e_r_b_e_r_o_s _/_e_t_c_/_r_c_._d_/_N_E_T_W_O_R_K _/_e_t_c_/_r_c_._d_/_s_y_s_t_e_m_f_s _/_e_t_c_/_r_c_._d_/_x_n_t_p_d and _/_e_t_c_/_r_c_._d_/_y_p_s_e_t. ++oo The users and groups `smmsp', needs to be created, `news' is no longer part of the system. The following issues need to be resolved manually: ++oo postfix(8) configuration files require upgrading. cd /usr/share/examples/postfix cp post-install postfix-files postfix-script /etc/postfix postfix check UUssiinngg oonnlliinnee NNeettBBSSDD ddooccuummeennttaattiioonn Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are ++oo intro(1), ++oo man(1), ++oo apropros(1), ++oo passwd(1), and ++oo passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The _m_a_n command is used to view the documentation on a topic, and is started by entering mmaann [_s_e_c_t_i_o_n] _t_o_p_i_c. The brackets [] around the section should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after logging in, enter # mmaann ppaasssswwdd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # mmaann 55 ppaasssswwdd instead. If you are unsure of what man page you are looking for, enter aapprrooppooss _s_u_b_j_e_c_t_-_w_o_r_d where _s_u_b_j_e_c_t_-_w_o_r_d is your topic of interest; a list of possibly related man pages will be displayed. AAddmmiinniissttrriivviiaa If you've got something to say, do so! We'd like your input. There are vari- ous mailing lists available via the mailing list server at _m_a_j_o_r_d_o_m_o_@_N_e_t_B_S_D_._o_r_g. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instructions. There are various mailing lists set up to deal with comments and questions about this release. Please send comments to: _n_e_t_b_s_d_-_c_o_m_m_e_n_t_s_@_N_e_t_B_S_D_._o_r_g. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: _n_e_t_b_s_d_-_b_u_g_s_@_N_e_t_B_S_D_._o_r_g. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit hhttttpp::////wwwwww..NNeettBBSSDD..oorrgg//MMaaiilliinnggLLiissttss//. If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: _n_e_t_b_s_d_-_h_e_l_p_@_N_e_t_B_S_D_._o_r_g. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW some- where, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. TThhaannkkss ggoo ttoo ++oo The former members of UCB's Computer Systems Research Group, including (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encouragement. ++oo The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. ++oo The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. ++oo The Helsinki University of Technology in Finland for hosting the NetBSD backup CVS and backup server. ++oo SSH Communications Security in Finland for operating the backup server. ++oo The many organisations that provide NetBSD mirror sites. ++oo Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. ++oo The following individuals and organizations (each in alphabetical order) have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it: AboveNet Communications, Inc. Advanced System Products, Inc. Alex Poylisher Alistair Crooks Andrew Brown Atsushi YOKOYAMA Avalon Computer Systems Bay Area Internet Solutions Ben Collver Bill Coldwell Bill Sommerfeld Brad Salai Brains Corporation, Japan Brian Carlstrom Brian McGroarty Canada Connect Corporation Castor Fu Central Iowa (Model) Railroad Charles Conn Charles D. Cranor Charles M. Hannum Chris Legrow Christer O. Andersson Christopher g. Demetriou Christos Zoulas Chuck Silvers Co-operative Research Centre for Enterprise Distributed Curt Sampson Dave Burgess Dave Rand David Brownlee Demon Internet, UK Derek Fellion Digital Equipment Corporation Distributed Processing Technology Douglas J. Trainor Easynet, UK Ed Braaten Edward Richley Eric and Rosemary Spahr Free Hardware Foundation Greg Gingerich Guenther Grau Harald Koerfgen Harry McDonald Heiko W. Rupp Herb Peyerl Hubert Feyrer Innovation Development Enterprises of America Internet Software Consortium James Chacon Jan Joris Vereijken Jason Birnschein Jason Brazile Jason R. Thorpe Jim Wise John Kohl Jonathan P. Kay Jordan K. Hubbard Kenneth Alan Hornstein Kevin Keith Woo Kimmo Suominen Krister Waldfridsson Lex Wennmacher LinuxFest Northwest Luke Mewburn MS Macro System GmbH, Germany Mark Brinicombe Mark S. Thomas Mason Loring Bliss Mattias Karlsson Michael Graff Michael L. Hitch Michael Richardson Michael Thompson Michael W. James Mike Price Neil J. McRae Noah M. Keiserman Norman R. McBride Numerical Aerospace Simulation Facility, NASA Ames Research Oliver Cahagne Perry E. Metzger Petri T. Koistinen Piermont Information Systems Inc. Precedence Technologies Ltd Ralph Campbell Reinoud Zandijk Richard Nelson Rob Windsor Ross Harvey SDF Public Access Unix, Inc. 501(c)(7) Salient Systems Inc. Scott Ellis Scott Kaplan Simon Burge Soren Jacobsen Soren Jorvang Steve Allen Steve Wadlow SunROOT# Project Ted Lemon Ted Spradley Thor Lancelot Simon Tim Law Tom Coulter Toru Nishimura VMC Harald Frank, Germany Warped Communications, Inc. Wasabi Systems Whitecross Database Systems Ltd. William Gnadt Worria Web Hosting (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) ++oo Finally, we thank all of the people who've put sweat and tears into devel- oping NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to mentioned, tell us!) WWee aarree...... (in alphabetical order) Allen Briggs _b_r_i_g_g_s_@_N_e_t_B_S_D_._o_r_g Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._o_r_g Luke Mewburn _l_u_k_e_m_@_N_e_t_B_S_D_._o_r_g Matt Thomas _m_a_t_t_@_N_e_t_B_S_D_._o_r_g Christos Zoulas _c_h_r_i_s_t_o_s_@_N_e_t_B_S_D_._o_r_g Allen Briggs _b_r_i_g_g_s_@_N_e_t_B_S_D_._o_r_g ssaannddppooiinntt Anders Magnusson _r_a_g_g_e_@_N_e_t_B_S_D_._o_r_g vvaaxx Andrey Petrov _p_e_t_r_o_v_@_N_e_t_B_S_D_._o_r_g ssppaarrcc6644 Ben Harris _b_j_h_2_1_@_N_e_t_B_S_D_._o_r_g aaccoorrnn2266 Chris Gilbert _c_h_r_i_s_@_N_e_t_B_S_D_._o_r_g ccaattss Christian Limpach _c_l_@_N_e_t_B_S_D_._o_r_g xxeenn Eduardo Horvath _e_e_h_@_N_e_t_B_S_D_._o_r_g eevvbbppppcc Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._o_r_g aammdd6644 Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._o_r_g ii338866 IWAMOTO Toshihiro _t_o_s_h_i_i_@_N_e_t_B_S_D_._o_r_g hhppccaarrmm Ichiro Fukuhara _i_c_h_i_r_o_@_N_e_t_B_S_D_._o_r_g hhppccaarrmm Ignatios Souvatzis _i_s_@_N_e_t_B_S_D_._o_r_g aammiiggaa Izumi Tsutsui _t_s_u_t_s_u_i_@_N_e_t_B_S_D_._o_r_g hhpp330000 Izumi Tsutsui _t_s_u_t_s_u_i_@_N_e_t_B_S_D_._o_r_g nneewwss6688kk Jason Thorpe _t_h_o_r_p_e_j_@_N_e_t_B_S_D_._o_r_g aallggoorr Jason Thorpe _t_h_o_r_p_e_j_@_N_e_t_B_S_D_._o_r_g sshhaarrkk Jeremy Cooper _j_e_r_e_m_y_@_N_e_t_B_S_D_._o_r_g ssuunn33 Jonathan Stone _j_o_n_a_t_h_a_n_@_N_e_t_B_S_D_._o_r_g ppmmaaxx Julian Coleman _j_d_c_@_N_e_t_B_S_D_._o_r_g aattaarrii Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._o_r_g eevvbbsshh33 Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._o_r_g mmmmeeyyee Kazuki Sakamoto _s_a_k_a_m_o_t_o_@_N_e_t_B_S_D_._o_r_g bbeebbooxx Lennart Augustsson _a_u_g_u_s_t_s_s_@_N_e_t_B_S_D_._o_r_g ppmmppppcc Marcus Comstedt _m_a_r_c_u_s_@_N_e_t_B_S_D_._o_r_g ddrreeaammccaasstt Martin Husemann _m_a_r_t_i_n_@_N_e_t_B_S_D_._o_r_g ssppaarrcc6644 Matt DeBergalis _d_e_b_e_r_g_@_N_e_t_B_S_D_._o_r_g nneexxtt6688kk Matt Fredette _f_r_e_d_e_t_t_e_@_N_e_t_B_S_D_._o_r_g hhpp770000 Matt Fredette _f_r_e_d_e_t_t_e_@_N_e_t_B_S_D_._o_r_g ssuunn22 Matt Thomas _m_a_t_t_@_N_e_t_B_S_D_._o_r_g aallpphhaa Matt Thomas _m_a_t_t_@_N_e_t_B_S_D_._o_r_g nneettwwiinnddeerr Matthias Drochner _d_r_o_c_h_n_e_r_@_N_e_t_B_S_D_._o_r_g cceessffiicc NISHIMURA Takeshi _n_s_m_r_t_k_s_@_N_e_t_B_S_D_._o_r_g xx6688kk NONAKA Kimihiro _n_o_n_a_k_a_@_N_e_t_B_S_D_._o_r_g pprreepp Nathan Williams _n_a_t_h_a_n_w_@_N_e_t_B_S_D_._o_r_g ssuunn33 Noriyuki Soda _s_o_d_a_@_N_e_t_B_S_D_._o_r_g aarrcc Paul Kranenburg _p_k_@_N_e_t_B_S_D_._o_r_g ssppaarrcc Phil Nelson _p_h_i_l_@_N_e_t_B_S_D_._o_r_g ppcc553322 Reinoud Zandijk _r_e_i_n_o_u_d_@_N_e_t_B_S_D_._o_r_g aaccoorrnn3322 Ross Harvey _r_o_s_s_@_N_e_t_B_S_D_._o_r_g aallpphhaa S(/oren J/orvang _s_o_r_e_n_@_N_e_t_B_S_D_._o_r_g ccoobbaalltt S(/oren J/orvang _s_o_r_e_n_@_N_e_t_B_S_D_._o_r_g ssggiimmiippss Scott Reynolds _s_c_o_t_t_r_@_N_e_t_B_S_D_._o_r_g mmaacc6688kk Shin Takemura _t_a_k_e_m_u_r_a_@_N_e_t_B_S_D_._o_r_g hhppccmmiippss Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._o_r_g eevvbbmmiippss Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._o_r_g eevvbbppppcc Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._o_r_g ppmmaaxx Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._o_r_g ssbbmmiippss Steve Woodford _s_c_w_@_N_e_t_B_S_D_._o_r_g eevvbbsshh55 Steve Woodford _s_c_w_@_N_e_t_B_S_D_._o_r_g mmvvmmee6688kk Steve Woodford _s_c_w_@_N_e_t_B_S_D_._o_r_g mmvvmmeeppppcc Tohru Nishimura _n_i_s_i_m_u_r_a_@_N_e_t_B_S_D_._o_r_g lluunnaa6688kk Tsubai Masanari _t_s_u_b_a_i_@_N_e_t_B_S_D_._o_r_g mmaaccppppcc Tsubai Masanari _t_s_u_b_a_i_@_N_e_t_B_S_D_._o_r_g nneewwssmmiippss UCHIYAMA Yasushi _u_c_h_@_N_e_t_B_S_D_._o_r_g hhppccsshh UCHIYAMA Yasushi _u_c_h_@_N_e_t_B_S_D_._o_r_g ppllaayyssttaattiioonn22 Wayne Knowles _w_d_k_@_N_e_t_B_S_D_._o_r_g mmiippssccoo Wolfgang Solfrank _w_s_@_N_e_t_B_S_D_._o_r_g ooffppppcc Grant Beattie _g_r_a_n_t_@_N_e_t_B_S_D_._o_r_g Erik Berls _c_y_b_e_r_@_N_e_t_B_S_D_._o_r_g James Chacon _j_m_c_@_N_e_t_B_S_D_._o_r_g Julian Coleman _j_d_c_@_N_e_t_B_S_D_._o_r_g Hoavard Eidnes _h_e_@_N_e_t_B_S_D_._o_r_g Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._o_r_g SAITOH Masanobu _m_s_a_i_t_o_h_@_N_e_t_B_S_D_._o_r_g Luke Mewburn _l_u_k_e_m_@_N_e_t_B_S_D_._o_r_g Matthias Scheler _t_r_o_n_@_N_e_t_B_S_D_._o_r_g Curt Sampson _c_j_s_@_N_e_t_B_S_D_._o_r_g Jim Wise _j_w_i_s_e_@_N_e_t_B_S_D_._o_r_g Nathan Ahlstrom _n_r_a_@_N_e_t_B_S_D_._o_r_g Steve Allen _w_o_r_m_e_y_@_N_e_t_B_S_D_._o_r_g Jukka Andberg _j_a_n_d_b_e_r_g_@_N_e_t_B_S_D_._o_r_g Julian Assange _p_r_o_f_f_@_N_e_t_B_S_D_._o_r_g Lennart Augustsson _a_u_g_u_s_t_s_s_@_N_e_t_B_S_D_._o_r_g Christoph Badura _b_a_d_@_N_e_t_B_S_D_._o_r_g Bang Jun-Young _j_u_n_y_o_u_n_g_@_N_e_t_B_S_D_._o_r_g Dieter Baron _d_i_l_l_o_@_N_e_t_B_S_D_._o_r_g Robert V. Baron _r_v_b_@_N_e_t_B_S_D_._o_r_g Grant Beattie _g_r_a_n_t_@_N_e_t_B_S_D_._o_r_g Jason Beegan _j_t_b_@_N_e_t_B_S_D_._o_r_g Erik Berls _c_y_b_e_r_@_N_e_t_B_S_D_._o_r_g Hiroyuki Bessho _b_s_h_@_N_e_t_B_S_D_._o_r_g John Birrell _j_b_@_N_e_t_B_S_D_._o_r_g Mason Loring Bliss _m_a_s_o_n_@_N_e_t_B_S_D_._o_r_g Charles Blundell _c_b_@_N_e_t_B_S_D_._o_r_g Rafal Boni _r_a_f_a_l_@_N_e_t_B_S_D_._o_r_g Manuel Bouyer _b_o_u_y_e_r_@_N_e_t_B_S_D_._o_r_g John Brezak _b_r_e_z_a_k_@_N_e_t_B_S_D_._o_r_g Allen Briggs _b_r_i_g_g_s_@_N_e_t_B_S_D_._o_r_g Mark Brinicombe _m_a_r_k_@_N_e_t_B_S_D_._o_r_g Aaron Brown _a_b_r_o_w_n_@_N_e_t_B_S_D_._o_r_g Andrew Brown _a_t_a_t_a_t_@_N_e_t_B_S_D_._o_r_g David Brownlee _a_b_s_@_N_e_t_B_S_D_._o_r_g Frederick Bruckman _f_r_e_d_b_@_N_e_t_B_S_D_._o_r_g Jon Buller _j_o_n_b_@_N_e_t_B_S_D_._o_r_g Simon Burge _s_i_m_o_n_b_@_N_e_t_B_S_D_._o_r_g Robert Byrnes _b_y_r_n_e_s_@_N_e_t_B_S_D_._o_r_g D'Arcy J.M. Cain _d_a_r_c_y_@_N_e_t_B_S_D_._o_r_g Dave Carrel _c_a_r_r_e_l_@_N_e_t_B_S_D_._o_r_g Daniel Carosone _d_a_n_@_N_e_t_B_S_D_._o_r_g James Chacon _j_m_c_@_N_e_t_B_S_D_._o_r_g Bill Coldwell _b_i_l_l_c_@_N_e_t_B_S_D_._o_r_g Julian Coleman _j_d_c_@_N_e_t_B_S_D_._o_r_g Ben Collver _b_e_n_@_N_e_t_B_S_D_._o_r_g Jeremy Cooper _j_e_r_e_m_y_@_N_e_t_B_S_D_._o_r_g Chuck Cranor _c_h_u_c_k_@_N_e_t_B_S_D_._o_r_g Alistair Crooks _a_g_c_@_N_e_t_B_S_D_._o_r_g Aidan Cully _a_i_d_a_n_@_N_e_t_B_S_D_._o_r_g Johan Danielsson _j_o_d_a_@_N_e_t_B_S_D_._o_r_g John Darrow _j_d_a_r_r_o_w_@_N_e_t_B_S_D_._o_r_g Matt DeBergalis _d_e_b_e_r_g_@_N_e_t_B_S_D_._o_r_g Rob Deker _d_e_k_e_r_@_N_e_t_B_S_D_._o_r_g Chris G. Demetriou _c_g_d_@_N_e_t_B_S_D_._o_r_g Tracy Di Marco White _g_e_n_d_a_l_i_a_@_N_e_t_B_S_D_._o_r_g Jarom'ir Dolecek _j_d_o_l_e_c_e_k_@_N_e_t_B_S_D_._o_r_g Andy Doran _a_d_@_N_e_t_B_S_D_._o_r_g Roland Dowdeswell _e_l_r_i_c_@_N_e_t_B_S_D_._o_r_g Emmanuel Dreyfus _m_a_n_u_@_N_e_t_B_S_D_._o_r_g Matthias Drochner _d_r_o_c_h_n_e_r_@_N_e_t_B_S_D_._o_r_g Jun Ebihara _j_u_n_@_N_e_t_B_S_D_._o_r_g Hoavard Eidnes _h_e_@_N_e_t_B_S_D_._o_r_g Stoned Elipot _s_e_b_@_N_e_t_B_S_D_._o_r_g Enami Tsugutomo _e_n_a_m_i_@_N_e_t_B_S_D_._o_r_g Bernd Ernesti _v_e_e_g_o_@_N_e_t_B_S_D_._o_r_g Erik Fair _f_a_i_r_@_N_e_t_B_S_D_._o_r_g Gavan Fantom _g_a_v_a_n_@_N_e_t_B_S_D_._o_r_g Hubert Feyrer _h_u_b_e_r_t_f_@_N_e_t_B_S_D_._o_r_g Jason R. Fink _j_r_f_@_N_e_t_B_S_D_._o_r_g Matt Fredette _f_r_e_d_e_t_t_e_@_N_e_t_B_S_D_._o_r_g Thorsten Frueauf _f_r_u_e_a_u_f_@_N_e_t_B_S_D_._o_r_g Castor Fu _c_a_s_t_o_r_@_N_e_t_B_S_D_._o_r_g Ichiro Fukuhara _i_c_h_i_r_o_@_N_e_t_B_S_D_._o_r_g Quentin Garnier _c_u_b_e_@_N_e_t_B_S_D_._o_r_g Thomas Gerner _t_h_o_m_a_s_@_N_e_t_B_S_D_._o_r_g Simon J. Gerraty _s_j_g_@_N_e_t_B_S_D_._o_r_g Justin Gibbs _g_i_b_b_s_@_N_e_t_B_S_D_._o_r_g Chris Gilbert _c_h_r_i_s_@_N_e_t_B_S_D_._o_r_g Eric Gillespie _e_p_g_@_N_e_t_B_S_D_._o_r_g Adam Glass _g_l_a_s_s_@_N_e_t_B_S_D_._o_r_g Michael Graff _e_x_p_l_o_r_e_r_@_N_e_t_B_S_D_._o_r_g Brian C. Grayson _b_g_r_a_y_s_o_n_@_N_e_t_B_S_D_._o_r_g Matthew Green _m_r_g_@_N_e_t_B_S_D_._o_r_g Andreas Gustafsson _g_s_o_n_@_N_e_t_B_S_D_._o_r_g Jun-ichiro itojun Hagino _i_t_o_j_u_n_@_N_e_t_B_S_D_._o_r_g Juergen Hannken-Illjes _h_a_n_n_k_e_n_@_N_e_t_B_S_D_._o_r_g Charles M. Hannum _m_y_c_r_o_f_t_@_N_e_t_B_S_D_._o_r_g Ben Harris _b_j_h_2_1_@_N_e_t_B_S_D_._o_r_g Ross Harvey _r_o_s_s_@_N_e_t_B_S_D_._o_r_g Eric Haszlakiewicz _e_r_h_@_N_e_t_B_S_D_._o_r_g John Hawkinson _j_h_a_w_k_@_N_e_t_B_S_D_._o_r_g HAYAKAWA Koichi _h_a_y_a_@_N_e_t_B_S_D_._o_r_g John Heasley _h_e_a_s_@_N_e_t_B_S_D_._o_r_g Ren'e Hexel _r_h_@_N_e_t_B_S_D_._o_r_g Michael L. Hitch _m_h_i_t_c_h_@_N_e_t_B_S_D_._o_r_g Christian E. Hopps _c_h_o_p_p_s_@_N_e_t_B_S_D_._o_r_g Ken Hornstein _k_e_n_h_@_N_e_t_B_S_D_._o_r_g Marc Horowitz _m_a_r_c_@_N_e_t_B_S_D_._o_r_g Eduardo Horvath _e_e_h_@_N_e_t_B_S_D_._o_r_g Nick Hudson _s_k_r_l_l_@_N_e_t_B_S_D_._o_r_g Shell Hung _s_h_e_l_l_@_N_e_t_B_S_D_._o_r_g Martin Husemann _m_a_r_t_i_n_@_N_e_t_B_S_D_._o_r_g Dean Huxley _d_e_a_n_@_N_e_t_B_S_D_._o_r_g Love H"ornquist oAstrand _l_h_a_@_N_e_t_B_S_D_._o_r_g Bernardo Innocenti _b_e_r_n_i_e_@_N_e_t_B_S_D_._o_r_g Tetsuya Isaki _i_s_a_k_i_@_N_e_t_B_S_D_._o_r_g ITOH Yasufumi _i_t_o_h_y_@_N_e_t_B_S_D_._o_r_g IWAMOTO Toshihiro _t_o_s_h_i_i_@_N_e_t_B_S_D_._o_r_g Matthew Jacob _m_j_a_c_o_b_@_N_e_t_B_S_D_._o_r_g Soren Jacobsen _s_n_j_@_N_e_t_B_S_D_._o_r_g Lonhyn T. Jasinskyj _l_o_n_h_y_n_@_N_e_t_B_S_D_._o_r_g Darrin Jewell _d_b_j_@_N_e_t_B_S_D_._o_r_g Chris Jones _c_j_o_n_e_s_@_N_e_t_B_S_D_._o_r_g S/oren J/orvang _s_o_r_e_n_@_N_e_t_B_S_D_._o_r_g Takahiro Kambe _t_a_c_a_@_N_e_t_B_S_D_._o_r_g Antti Kantee _p_o_o_k_a_@_N_e_t_B_S_D_._o_r_g Masanori Kanaoka _k_a_n_a_o_k_a_@_N_e_t_B_S_D_._o_r_g Mattias Karlsson _k_e_i_h_a_n_@_N_e_t_B_S_D_._o_r_g KAWAMOTO Yosihisa _k_a_w_a_m_o_t_o_@_N_e_t_B_S_D_._o_r_g Mario Kemper _m_a_g_i_c_k_@_N_e_t_B_S_D_._o_r_g Min Sik Kim _m_i_n_s_k_i_m_@_N_e_t_B_S_D_._o_r_g Thomas Klausner _w_i_z_@_N_e_t_B_S_D_._o_r_g Klaus Klein _k_l_e_i_n_k_@_N_e_t_B_S_D_._o_r_g Wayne Knowles _w_d_k_@_N_e_t_B_S_D_._o_r_g Takayoshi Kochi _k_o_c_h_i_@_N_e_t_B_S_D_._o_r_g John Kohl _j_t_k_@_N_e_t_B_S_D_._o_r_g Daniel de Kok _d_a_n_i_e_l_@_N_e_t_B_S_D_._o_r_g Paul Kranenburg _p_k_@_N_e_t_B_S_D_._o_r_g Martti Kuparinen _m_a_r_t_t_i_@_N_e_t_B_S_D_._o_r_g Kevin Lahey _k_m_l_@_N_e_t_B_S_D_._o_r_g Johnny C. Lam _j_l_a_m_@_N_e_t_B_S_D_._o_r_g Martin J. Laubach _m_j_l_@_N_e_t_B_S_D_._o_r_g Greg Lehey _g_r_o_g_@_N_e_t_B_S_D_._o_r_g Ted Lemon _m_e_l_l_o_n_@_N_e_t_B_S_D_._o_r_g Christian Limpach _c_l_@_N_e_t_B_S_D_._o_r_g Frank van der Linden _f_v_d_l_@_N_e_t_B_S_D_._o_r_g Joel Lindholm _j_o_e_l_@_N_e_t_B_S_D_._o_r_g Mike Long _m_i_k_e_l_@_N_e_t_B_S_D_._o_r_g Warner Losh _i_m_p_@_N_e_t_B_S_D_._o_r_g Tomasz Luchowski _z_u_n_t_u_m_@_N_e_t_B_S_D_._o_r_g Federico Lupi _f_e_d_e_r_i_c_o_@_N_e_t_B_S_D_._o_r_g Brett Lymn _b_l_y_m_n_@_N_e_t_B_S_D_._o_r_g Paul Mackerras _p_a_u_l_u_s_@_N_e_t_B_S_D_._o_r_g Anders Magnusson _r_a_g_g_e_@_N_e_t_B_S_D_._o_r_g MAEKAWA Masahide _g_e_h_e_n_n_a_@_N_e_t_B_S_D_._o_r_g David Maxwell _d_a_v_i_d_@_N_e_t_B_S_D_._o_r_g Dan McMahill _d_m_c_m_a_h_i_l_l_@_N_e_t_B_S_D_._o_r_g Gregory McGarry _g_m_c_g_a_r_r_y_@_N_e_t_B_S_D_._o_r_g Jared D. McNeill _j_m_c_n_e_i_l_l_@_N_e_t_B_S_D_._o_r_g Neil J. McRae _n_e_i_l_@_N_e_t_B_S_D_._o_r_g Perry Metzger _p_e_r_r_y_@_N_e_t_B_S_D_._o_r_g Simas Mockevicius _s_y_m_k_a_@_N_e_t_B_S_D_._o_r_g Juan Romero Pardines _x_t_r_a_e_m_e_@_N_e_t_B_S_D_._o_r_g Julio M. Merino Vidal _j_m_m_v_@_N_e_t_B_S_D_._o_r_g Minoura Makoto _m_i_n_o_u_r_a_@_N_e_t_B_S_D_._o_r_g Luke Mewburn _l_u_k_e_m_@_N_e_t_B_S_D_._o_r_g der Mouse _m_o_u_s_e_@_N_e_t_B_S_D_._o_r_g Joseph Myers _j_s_m_@_N_e_t_B_S_D_._o_r_g Ken Nakata _k_e_n_n_@_N_e_t_B_S_D_._o_r_g Takeshi Nakayama _n_a_k_a_y_a_m_a_@_N_e_t_B_S_D_._o_r_g Phil Nelson _p_h_i_l_@_N_e_t_B_S_D_._o_r_g Bob Nestor _r_n_e_s_t_o_r_@_N_e_t_B_S_D_._o_r_g NISHIMURA Takeshi _n_s_m_r_t_k_s_@_N_e_t_B_S_D_._o_r_g Tohru Nishimura _n_i_s_i_m_u_r_a_@_N_e_t_B_S_D_._o_r_g NONAKA Kimihiro _n_o_n_a_k_a_@_N_e_t_B_S_D_._o_r_g Jesse Off _j_o_f_f_@_N_e_t_B_S_D_._o_r_g Tatoku Ogaito _t_a_c_h_a_@_N_e_t_B_S_D_._o_r_g OKANO Takayoshi _k_a_n_o_@_N_e_t_B_S_D_._o_r_g Masaru Oki _o_k_i_@_N_e_t_B_S_D_._o_r_g Atsushi Onoe _o_n_o_e_@_N_e_t_B_S_D_._o_r_g Greg Oster _o_s_t_e_r_@_N_e_t_B_S_D_._o_r_g Jonathan Perkin _s_k_e_t_c_h_@_N_e_t_B_S_D_._o_r_g Herb Peyerl _h_p_e_y_e_r_l_@_N_e_t_B_S_D_._o_r_g Matthias Pfaller _m_a_t_t_h_i_a_s_@_N_e_t_B_S_D_._o_r_g Chris Pinnock _c_j_e_p_@_N_e_t_B_S_D_._o_r_g Adrian Portelli _a_d_r_i_a_n_p_@_N_e_t_B_S_D_._o_r_g Dante Profeta _d_a_n_t_e_@_N_e_t_B_S_D_._o_r_g Chris Provenzano _p_r_o_v_e_n_@_N_e_t_B_S_D_._o_r_g Niels Provos _p_r_o_v_o_s_@_N_e_t_B_S_D_._o_r_g Michael Rauch _m_r_a_u_c_h_@_N_e_t_B_S_D_._o_r_g Marc Recht _r_e_c_h_t_@_N_e_t_B_S_D_._o_r_g Darren Reed _d_a_r_r_e_n_r_@_N_e_t_B_S_D_._o_r_g Jeremy C. Reed _r_e_e_d_@_N_e_t_B_S_D_._o_r_g Tyler R. Retzlaff _r_t_r_@_N_e_t_B_S_D_._o_r_g Scott Reynolds _s_c_o_t_t_r_@_N_e_t_B_S_D_._o_r_g Michael Richardson _m_c_r_@_N_e_t_B_S_D_._o_r_g Tim Rightnour _g_a_r_b_l_e_d_@_N_e_t_B_S_D_._o_r_g Gordon Ross _g_w_r_@_N_e_t_B_S_D_._o_r_g Steve Rumble _r_u_m_b_l_e_@_N_e_t_B_S_D_._o_r_g Ilpo Ruotsalainen _l_o_n_e_w_o_l_f_@_N_e_t_B_S_D_._o_r_g Heiko W. Rupp _h_w_r_@_N_e_t_B_S_D_._o_r_g David Sainty _d_s_a_i_n_t_y_@_N_e_t_B_S_D_._o_r_g SAITOH Masanobu _m_s_a_i_t_o_h_@_N_e_t_B_S_D_._o_r_g Kazuki Sakamoto _s_a_k_a_m_o_t_o_@_N_e_t_B_S_D_._o_r_g Curt Sampson _c_j_s_@_N_e_t_B_S_D_._o_r_g Wilfredo Sanchez _w_s_a_n_c_h_e_z_@_N_e_t_B_S_D_._o_r_g Ty Sarna _t_s_a_r_n_a_@_N_e_t_B_S_D_._o_r_g SATO Kazumi _s_a_t_o_@_N_e_t_B_S_D_._o_r_g Jan Schaumann _j_s_c_h_a_u_m_a_@_N_e_t_B_S_D_._o_r_g Matthias Scheler _t_r_o_n_@_N_e_t_B_S_D_._o_r_g Karl Schilke (rAT) _r_a_t_@_N_e_t_B_S_D_._o_r_g Amitai Schlair _s_c_h_m_o_n_z_@_N_e_t_B_S_D_._o_r_g Konrad Schroder _p_e_r_s_e_a_n_t_@_N_e_t_B_S_D_._o_r_g Lubomir Sedlacik _s_a_l_o_@_N_e_t_B_S_D_._o_r_g Christopher SEKIYA _s_e_k_i_y_a_@_N_e_t_B_S_D_._o_r_g Reed Shadgett _d_e_n_t_@_N_e_t_B_S_D_._o_r_g John Shannon _s_h_a_n_n_o_n_j_r_@_N_e_t_B_S_D_._o_r_g Tim Shepard _s_h_e_p_@_N_e_t_B_S_D_._o_r_g Takeshi Shibagaki _s_h_i_b_a_@_N_e_t_B_S_D_._o_r_g Naoto Shimazaki _i_g_y_@_N_e_t_B_S_D_._o_r_g Takao Shinohara _s_h_i_n_@_N_e_t_B_S_D_._o_r_g Takuya SHIOZAKI _t_s_h_i_o_z_a_k_@_N_e_t_B_S_D_._o_r_g Chuck Silvers _c_h_s_@_N_e_t_B_S_D_._o_r_g Thor Lancelot Simon _t_l_s_@_N_e_t_B_S_D_._o_r_g Jeff Smith _j_e_f_f_s_@_N_e_t_B_S_D_._o_r_g Noriyuki Soda _s_o_d_a_@_N_e_t_B_S_D_._o_r_g Wolfgang Solfrank _w_s_@_N_e_t_B_S_D_._o_r_g SOMEYA Yoshihiko _s_o_m_e_y_a_@_N_e_t_B_S_D_._o_r_g Bill Sommerfeld _s_o_m_m_e_r_f_e_l_d_@_N_e_t_B_S_D_._o_r_g Ignatios Souvatzis _i_s_@_N_e_t_B_S_D_._o_r_g Bill Squier _g_r_o_o_@_N_e_t_B_S_D_._o_r_g Jonathan Stone _j_o_n_a_t_h_a_n_@_N_e_t_B_S_D_._o_r_g Bill Studenmund _w_r_s_t_u_d_e_n_@_N_e_t_B_S_D_._o_r_g Kevin Sullivan _s_u_l_l_i_v_a_n_@_N_e_t_B_S_D_._o_r_g SUNAGAWA Keiki _k_e_i_@_N_e_t_B_S_D_._o_r_g Kimmo Suominen _k_i_m_@_N_e_t_B_S_D_._o_r_g Shin Takemura _t_a_k_e_m_u_r_a_@_N_e_t_B_S_D_._o_r_g TAMURA Kent _k_e_n_t_@_N_e_t_B_S_D_._o_r_g Shin'ichiro TAYA _t_a_y_a_@_N_e_t_B_S_D_._o_r_g Ian Lance Taylor _i_a_n_@_N_e_t_B_S_D_._o_r_g Matt Thomas _m_a_t_t_@_N_e_t_B_S_D_._o_r_g Jason Thorpe _t_h_o_r_p_e_j_@_N_e_t_B_S_D_._o_r_g Christoph Toshok _t_o_s_h_o_k_@_N_e_t_B_S_D_._o_r_g Tsubai Masanari _t_s_u_b_a_i_@_N_e_t_B_S_D_._o_r_g Izumi Tsutsui _t_s_u_t_s_u_i_@_N_e_t_B_S_D_._o_r_g UCHIYAMA Yasushi _u_c_h_@_N_e_t_B_S_D_._o_r_g Masao Uebayashi _u_e_b_a_y_a_s_i_@_N_e_t_B_S_D_._o_r_g Shuichiro URATA _u_r_@_N_e_t_B_S_D_._o_r_g Todd Vierling _t_v_@_N_e_t_B_S_D_._o_r_g Aymeric Vincent _a_y_m_e_r_i_c_@_N_e_t_B_S_D_._o_r_g Paul Vixie _v_i_x_i_e_@_N_e_t_B_S_D_._o_r_g Krister Walfridsson _k_r_i_s_t_e_r_w_@_N_e_t_B_S_D_._o_r_g Lex Wennmacher _w_e_n_n_m_a_c_h_@_N_e_t_B_S_D_._o_r_g Leo Weppelman _l_e_o_@_N_e_t_B_S_D_._o_r_g Assar Westerlund _a_s_s_a_r_@_N_e_t_B_S_D_._o_r_g Todd Whitesel _t_o_d_d_p_w_@_N_e_t_B_S_D_._o_r_g Nathan Williams _n_a_t_h_a_n_w_@_N_e_t_B_S_D_._o_r_g Rob Windsor _w_i_n_d_s_o_r_@_N_e_t_B_S_D_._o_r_g Dan Winship _d_a_n_w_@_N_e_t_B_S_D_._o_r_g Jim Wise _j_w_i_s_e_@_N_e_t_B_S_D_._o_r_g Michael Wolfson _m_b_w_@_N_e_t_B_S_D_._o_r_g Steve Woodford _s_c_w_@_N_e_t_B_S_D_._o_r_g Colin Wood _e_n_d_e_r_@_N_e_t_B_S_D_._o_r_g YAMAMOTO Takashi _y_a_m_t_@_N_e_t_B_S_D_._o_r_g Yuji Yamano _y_y_a_m_a_n_o_@_N_e_t_B_S_D_._o_r_g Reinoud Zandijk _r_e_i_n_o_u_d_@_N_e_t_B_S_D_._o_r_g Maria Zevenhoven _m_a_r_i_a_7_@_N_e_t_B_S_D_._o_r_g Christos Zoulas _c_h_r_i_s_t_o_s_@_N_e_t_B_S_D_._o_r_g Dave Burgess _b_u_r_g_e_s_s_@_c_y_n_j_u_t_._i_n_f_o_n_e_t_._n_e_t Brian R. Gaeke _b_r_g_@_d_g_a_t_e_._o_r_g Brad Grantham _g_r_a_n_t_h_a_m_@_t_e_n_o_n_._c_o_m Lawrence Kesteloot _k_e_s_t_e_l_o_o_@_c_s_._u_n_c_._e_d_u Waldi Ravens _w_a_l_d_i_@_m_o_a_c_s_._i_n_d_i_v_._n_l_._n_e_t LLeeggaall MMuummbboo--JJuummbboo All product names mentioned herein are trademarks or registered trademarks of their respective owners. The following notices are required to satisfy the license terms of the soft- ware that we have mentioned in this document: This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product contains software developed by Ignatios Souvatzis for the NetBSD project. This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project. This product contains software written by Michael L. Hitch for the NetBSD project. This product includes cryptographic software written by Eric Young (eay@crypt- soft.com) This product includes cryptographic software written by Eric Young (eay@min- com.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Divi- sion, US Naval Research Laboratory. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Gordon W. Ross and Leo Weppelman. This product includes software developed by Hellmuth Michaelis and Joerg Wun- sch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Univer- sity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Alistair G. Crooks. This product includes software developed by Alistair G. Crooks. for the NetBSD project. This product includes software developed by Allen Briggs This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, sub- stitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brad Pepers This product includes software developed by Bradley A. Grantham. This product includes software developed by Brini. This product includes software developed by Causality Limited. This product includes software developed by Charles D. Cranor and Seth Widoff. This product includes software developed by Charles D. Cranor and Washington University. This product includes software developed by Charles D. Cranor, Washington Uni- versity, and the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor, Washington Uni- versity, the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the Univer- sity of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christian Limpach This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Cybernet Corporation and Nan Yang Computer Services Limited This product includes software developed by Daishi Kato This product includes software developed by Dale Rahn. This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Darrin B. Jewell This product includes software developed by David Miller. This product includes software developed by Dean Huxley. This product includes software developed by Eduardo Horvath. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@mincom.oz.au) This product includes software developed by Eric Young (eay@cryptsoft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by Ezra Story and by Kari Mettinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Gordon W. Ross This product includes software developed by HAYAKAWA Koichi. This product includes software developed by Harvard University and its con- tributors. This product includes software developed by Harvard University. This product includes software developed by Herb Peyerl. This product includes software developed by Hubert Feyrer for the NetBSD Project. This product includes software developed by Iain Hibbert This product includes software developed by Ian F. Darwin and others. This product includes software developed by Ian W. Dall. This product includes software developed by Ichiro FUKUHARA. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jared D. McNeill. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Communica- tions, http://www.and.com/ This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Jukka Marin. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berkeley and its con- tributors. This product includes software developed by LAN Media Corporation and its con- tributors. This product includes software developed by Leo Weppelman for the NetBSD Project. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Luke Mewburn. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Manuel Bouyer. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Murray This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Sol- frank. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Mats O Jansson and Charles D. Cra- nor. This product includes software developed by Mats O Jansson. This product includes software developed by Matt DeBergalis This product includes software developed by Matthew Fredette. This product includes software developed by Matthias Pfaller. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Michael Graff. This product includes software developed by Michael L. Hitch. This product includes software developed by Michael Shalayeff. This product includes software developed by Michael Smith. This product includes software developed by Mike Glover and contributors. This product includes software developed by Mike Pritchard. This product includes software developed by Minoura Makoto. This product includes software developed by Nan Yang Computer Services Lim- ited. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Onno van der Linden. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by Philip L. Budne. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Roland C. Dowdeswell. This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Soren S. Jorvang. This product includes software developed by Stephan Thesing. This product includes software developed by Steve Woodford. This product includes software developed by Takashi Hamada This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by Tetsuya Isaki. This product includes software developed by Thomas Gerner This product includes software developed by Thomas Klausner for the NetBSD Project. This product includes software developed by Tobias Weingartner. This product includes software developed by Todd C. Miller. This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project. This product includes software developed by Tohru Nishimura for the NetBSD Project. This product includes software developed by Tohru Nishimura. for the NetBSD Project. This product includes software developed by TooLs GmbH. This product includes software developed by Toru Nishimura. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contributors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Science at the University of Utah. This product includes software developed by the Charles D. Cranor, Washington University, University of California, Berkeley and its contributors. This product includes software developed by the Computer Systems Engineering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Kungliga Tekniska H"ogskolan and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) his product includes software developed by the PocketBSD project and its con- tributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Development Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia University. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Christos Zoulas This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Ignatios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Michael L. Hitch. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bar- tram and Frank van der Linden This product includes software developed for the NetBSD Project by Allegro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Piermont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Sys- tems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsy- con AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, Tele- Muse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Laboratory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Brini. This product includes software developed by Mark Brinicombe for the NetBSD Project. This product includes software developed by Mark Brinicombe. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Charles M. Hannum. This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes software developed by TooLs GmbH. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed for the NetBSD Project by Wasabi Sys- tems, Inc. TThhee EEnndd NetBSD August 22, 2004 NetBSD