INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL - Installation procedure for NetBSD/news68k. CONTENTS About this Document............................................2 What is NetBSD?................................................2 Changes Between The NetBSD 2.0 and 2.1 Releases................3 Kernel......................................................3 Networking..................................................3 File system.................................................4 Security....................................................4 System administration and user tools........................4 Miscellaneous...............................................5 news68k specific............................................5 Changes Between The NetBSD 1.6 and 2.0 Releases................5 Kernel......................................................5 Networking..................................................6 File system.................................................6 Security....................................................6 System administration and user tools........................6 Miscellaneous...............................................6 Important notes about NetBSD 2.1...............................7 The Future of NetBSD...........................................7 Sources of NetBSD..............................................8 NetBSD 2.1 Release Contents....................................8 NetBSD/news68k subdirectory structure.......................9 Binary distribution sets...................................10 NetBSD/news68k System Requirements and Supported Devices......11 Supported hardware.........................................11 Getting the NetBSD System on to Useful Media..................12 Preparing your System for NetBSD installation.................13 Installing the NetBSD System..................................13 Running the sysinst installation program...................13 Introduction............................................13 General.................................................14 Quick install...........................................14 Booting NetBSD..........................................15 Network configuration...................................16 Installation drive selection and parameters.............16 Partitioning the disk...................................16 Preparing your hard disk................................16 Getting the distribution sets...........................17 Installation using ftp..................................17 Installation using NFS..................................17 Installation from CD-ROM................................18 Installation from an unmounted file system..............18 Installation from a local directory.....................18 Extracting the distribution sets........................18 Finalizing your installation............................18 Post installation steps.......................................18 Upgrading a previously-installed NetBSD System................21 Compatibility Issues With Previous NetBSD Releases............22 Issues affecting an upgrade from NetBSD 1.6................22 Using online NetBSD documentation.............................22 Administrivia.................................................23 Thanks go to..................................................23 We are........................................................26 Legal Mumbo-Jumbo.............................................31 The End.......................................................37 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 2.1 on the news68k platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX -like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX -like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on fifty four different system architectures (ports), featuring sev- enteen machine architectures across fifteen distinct CPU families, and is being ported to more. The NetBSD 2.1 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distri- bution. For information on them, please see the NetBSD web site at .: http://www.NetBSD.org/) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Changes Between The NetBSD 2.0 and 2.1 Releases The NetBSD 2.1 release is the first functional update release of the NetBSD 2 release branch. This provides numerous functional enhancements, including support for many new devices, hundreds of bug fixes, patches and updates to kernel subsystems, and many enhancements to the user envi- ronment. In addition, all of the security fixes and critical bug fixes from the NetBSD 2.0.3 update are included as well. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize all the changes that have gone in over the over nine months since the release of NetBSD 2.0. Some high- lights include: Kernel o Fix a bug that caused spontaneous reboot under heavy load on SH3/4 platforms. o Fixed some sparc64 and alpha pmap issues. o A longstanding bug in the SYSV semaphore code has been fixed. o Eliminated hangs when large processes fork. o ata(4) and wdc(4) drives now only downgrade modes due to actual CRC errors, and UDMA modes are downgraded more slowly. o The pdcsata(4) driver was added, with support for the Promise SATA150 series of controllers, including RAID support. o The RAIDframe disk driver had various bugfixes and improvements. o Added support for various devices from the nVidia nForce3 chipset. (i386, amd64) o Fixed interrupt problems on some Intel Xeon systems. o Added support for the VT642 SATA RAID Controller. o Various fixes to the esiop(4) driver. o Added support for the Dell CERC SATA RAID to the aac(4) driver. o Added support for additional Dell boards to the ahd(4) driver. o Fix a number of issues with the ehci(4) driver. o Added ukyopon(4) : Kyocera AIR-EDGE phone driver. o The wdc(4) driver has been fixed for commands with opaque data struc- tures. atactl smart status now works on big-endian hosts. Networking o wm(4) fixed major performance issues with the i82547 Gig-E chip. o sk(4) improved chip identification and improved performance, and added support for the Belkin Gigabit Desktop Network PCI card. o Fix a bug which would crash the system when destroying vlan(4) inter- faces. o Added rtk(4) and tl(4) interfaces as rnd(4) sources. o Added support for the Compaq Netelligent 10 T/2 PCI UTP/Coax Con- troller to the tl(4) driver. o Added support for changing the MTU of an stf(4) interface. o Added support for IPv6 over gre(4) interfaces. o The hme(4) driver now supports Sun QFE boards on non-sparc hardware. o stge(4) Fix some bigendian issues, and some other issues. Now works on sparc64 with hardware checksums. File system o Fix a number of NFS issues. o Fixed file access problems via SMBFS when the file is already open on the server. o Various improvements to LFS, the BSD log-structured file system. Security o krb5(3) Support changing passwords in a Windows 2000 (or later) domain. o Fixed a possible Denial of Service attack via IPSec AH packets. o NetBSD-SA2005-07 AES-XCBC-MAC always caculated with same key o NetBSD-SA2005-06 Multiple vulnerabilites in CVS o NetBSD-SA2005-05 cgd(4) key destruction on unconfigure o NetBSD-SA2005-04 Buffer overflows in MIT Kerberos 5 telnet client o NetBSD-SA2005-03 F_CLOSEM local denial of service o NetBSD-SA2005-02 Local DoS via audio device with specific drivers System administration and user tools o ntpd(8) coredump if local system and NTP server did not have overlap- ping protocol family support (IPv4 vs. IPv6, for example) fixed. o pax(1) has a number of bugfixes and new features. o ifwatchd(8) has been fixed to call the CARRIER script if a link is already up during the initial interface scan. o CVS has been upgraded to version 1.11.20. o Avoid crashes in grep(1) on empty or very large files. o Fixed a number of issues in gzip(1) Miscellaneous o Added VT switching for the cats port. o Various fixes and improvements to the cross-build system. o Fixed some issues in libpthread and libpthread_dbg. o Implement a USB memory reserve to work around problems plugging in (for example) umass(4) devices after boot. o Package tools have been upgraded to version 20050530. news68k specific This is the second major release of NetBSD for the Sony's news68k based ``NET WORK STATION'' series of computers. Changes Between The NetBSD 1.6 and 2.0 Releases The NetBSD 2.0 release provides numerous significant functional enhance- ments, including support for many new devices, integration of hundreds of bug fixes, new and updated kernel subsystems, and many user-land enhance- ments. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize over two years of development that went into the NetBSD 2.1 release. Some highlights include: Kernel o Ports to new platforms including: amd64, evbsh5, and xen. o Native thread support has been added, based on Scheduler Activations. Applications which support native threads can now take full advantage of the high-performance NetBSD POSIX threads implementation. o Kernel events notification framework - kqueue kqueue provides a stateful and efficient event notification framework. Currently sup- ported events include socket, file, directory, fifo, pipe, tty and device changes, and monitoring of processes and signals. kqueue is supported by all writable filesystems in the NetBSD tree (with the exception of Coda) and all device drivers supporting poll(2). o Improvements have been made to NetBSD's Linux emulation to support the latest Sun JDK/JRE for Linux. Testing has shown that it now runs as well as it does on Linux natively. o NetBSD 2.0 enforces non-executable mappings on many platforms. This means that parts of the stack and heap are made non-executable when they are marked writable. This makes exploiting potential buffer overflows harder. o For the i386 port it now supports SMP and has a new ACPI and power management framework which takes advantage of Intel's ACPI implemen- tation. o The macppc port also now supports SMP as well as hardware support for newer G4 models has been added. o SMP support has been added to the sparc port as well. o New generic i2c framework, supporting bit-bang and "intelligent" con- trollers. o sysctl(9) was switched from a static binding to a dynamic implementa- tion. o Add a new driver satalink(4) and move SATA support from other con- trollers into this along with adding support for new controllers. Networking o ipf(8) has been upgraded to version 4.1.3. o tcp(4) now implements path MTU discovery blackhole detection (i.e. it will turn off path MTU discovery if the connection is losing). o Socket buffer insertion is now O(C). This can provide a substantial performance boost to some applications which use large socket buffers. o wi(4) has support for Host-AP mode, allowing Intersil Prism2/2.5/3-based boards to be used to make an 802.11 Access Point. o Support for ipf(8) has been added to bridge(4) and brconfig(8) o Change port allocation from linked list to a hash table for better performance. File system o FreeBSD's UFS2 has been ported to NetBSD. UFS2 is an extension to FFS, adding 64 bit block pointers and support for extended file stor- age. Among other enhancements, UFS2 allows for file systems larger than 1Terabyte. o The cryptographic disk driver (cgd) can be used to encrypt disks or partitions, using some strong encryption algorithms, like AES (Rijn- dael) and Blowfish. cgd can also be configured to encrypt swap. Security o The systrace utility has been added to the system. systrace monitors and controls an application access to the system by enforcing access policies for system calls. The systrace utility might be used to trace an untrusted application's access to the system. In addition, it can be used to protect the system from software bugs (such as buffer overflows) by constraining a daemon's access to the system. The privilege elevation feature of systrace can be used to obviate the need to run large, untrusted programs as root when only one or two system calls require the elevated privilege. o Verified Exec support has been added in this release. Verified Exec verifies a cryptographic hash before allowing execution of binaries and scripts. This can be used to prevent a system from running bina- ries or scripts which have been illegally modified or installed. In addition, Verified Exec can also be used to limit the use of script interpreters to authorized scripts only and disallow interactive use. System administration and user tools o Switched from the GPL version to a non-GPL version of various tools including gzip and awk. Miscellaneous o NetBSD 2.0 supports a new toolchain based on gcc 3.3.3 and binutils 2.14. gcc 3.3.1 adds support for a number of CPU targets and greatly improved support for i386 and other targets. The support for new platforms in gcc 3.3.3 has enabled the porting of NetBSD to even more architectures. o Updates of most third party packages that are shipped in the base system to the following latest stable releases: - bind 8.3.7 - binutils 2.14 - cvs 1.11.17 - diffutils 2.8.1 - file 4.08 - gcc 3.3.3 - gdb 5.3 - grep 2.5.1 - groff 1.19 - less 381 - openssl 0.9.7d - postfix 2.0.19 - sendmail 8.12.11 - tcpump 3.7.1 - texinfo 4.6 o Many new packages in the pkgsrc system, including the latest open source desktop KDE3, OpenOffice, perl, Apache and many more. A num- ber of new platforms are supported, including Darwin, FreeBSD, IRIX, Linux, OpenBSD and Solaris. Support for various other platforms (among them AIX, BSD/OS and HP-UX) is currently being worked on thanks to our new, portable bootstrap kit which makes it much simpler to port pkgsrc support to new operating systems. At the time of writing, there are over 5400 third party packages available in pkgsrc. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. Important notes about NetBSD 2.1 o As noted above, the sendmail third-party program has been upgraded since the last release. The new version of sendmail runs without requiring being set-user-ID to ``root''. In order to retain the functionality that a newly installed system can send mail ``out of the box'', the default has changed so that sendmail will now start by default, and listen for host-local connec- tions. If this behaviour is not desired, you can either 1. explicitly set the sendmail variable to ``NO'' in /etc/rc.conf, 2. modify /etc/mail/submit.cf to point to another host, 3. modify /etc/mailer.conf to point to something else than send- mail, or 4. make sendmail set-user-ID to ``root'', remove /etc/mail/submit.cf, and set the sendmail_suid variable to ``YES'' in /etc/rc.conf. The latter method is strongly discouraged. The Future of NetBSD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: o providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. o providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. o providing a better position from which to undertake promotional activities. o periodically organizing workshops for developers and other interested people to discuss ongoing work. We intend to begin narrowing the time delay between releases. Our ambi- tion is to provide a full release every six to eight months. We hope to support even more hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the usability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. Sources of NetBSD Refer to .: http://www.NetBSD.org/mirrors/ NetBSD 2.1 Release Contents The root directory of the NetBSD 2.1 release is organized as follows: .../NetBSD-2.1/ CHANGES Changes since earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 2.1 distribution. README.files README describing the distribution's contents. TODO NetBSD 's todo list (also somewhat incomplete and out of date). patches/ Post-release source code patches. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 2.1 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. 79 MB gzipped, 367 MB uncompressed pkgsrc This set contains the ``pkgsrc'' sources, which contain the in- frastructure to build third-party packages. 24 MB gzipped, 200 MB uncompressed sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. 5 MB gzipped, 20 MB uncompressed src This set contains all of the base NetBSD 2.1 sources which are not in gnusrc, sharesrc, or syssrc. 37 MB gzipped, 176 MB uncompressed syssrc This set contains the sources to the NetBSD 2.1 kernel for all architectures; config(8); and dbsym(8). 26 MB gzipped, 140 MB uncompressed xsrc This set contains the sources to the X Window System. 84 MB gzipped, 450 MB uncompressed All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # ( cd / ; tar -zxpf - ) set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: BSDSUM Historic BSD checksums for the various files in that directory, in the format produced by the command: cksum -o 1 file. CKSUM POSIX checksums for the various files in that directory, in the format produced by the command: cksum file. MD5 MD5 digests for the various files in that directory, in the format produced by the command: cksum -m file. SYSVSUM Historic ATT System V UNIX checksums for the various files in that directory, in the format produced by the command: cksum -o 2 file. The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest pos- sible range of system can check the integrity of the release files. NetBSD/news68k subdirectory structure The news68k-specific portion of the NetBSD 2.1 release is found in the news68k subdirectory of the distribution: .../NetBSD-2.1/news68k/. It contains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-GENERIC.gz A gzipped NetBSD kernel containing code for everything supported in this release. sets/ news68k binary distribution sets; see below. installation/ floppy/ news68k boot and installation floppies; see below. misc/ Binary distribution sets The NetBSD news68k binary distribution sets contain the binaries which comprise the NetBSD 2.1 release for the news68k. The binary distribution sets can be found in the news68k/binary/sets subdirectory of the NetBSD 2.1 distribution tree, and are as follows: base The NetBSD 2.1 news68k base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be mini- mally functional. It includes shared library support, and excludes everything described below. 16 MB gzipped, 45 MB uncompressed comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. 18 MB gzipped, 69 MB uncompressed etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. 1 MB gzipped, 1 MB uncompressed games This set includes the games and their manual pages. 3 MB gzipped, 7 MB uncompressed kern-GENERIC This set contains a NetBSD/news68k 2.1 GENERIC kernel, named /netbsd. You must install this distribution set. 2 MB gzipped, 3 MB uncompressed man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. 8 MB gzipped, 30 MB uncompressed misc This set includes the (rather large) system dictionaries, the typesettable document set, and other files from /usr/share. 3 MB gzipped, 9 MB uncompressed text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. 2 MB gzipped, 7 MB uncompressed NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 4.4.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. 6 MB gzipped, 17 MB uncompressed xcomp The extra libraries and include files needed to compile X source code. 10 MB gzipped, 37 MB uncompressed xfont Fonts needed by X. 31 MB gzipped, 39 MB uncompressed xetc Configuration files for X which could be locally modified. 0.03 MB gzipped, 0.17 MB uncompressed xserver The X server. 3 MB gzipped, 7 MB uncompressed The news68k binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xpf command from the root directory ( / ) of your system. This utility is used only in a Traditional method installation. Note: Each directory in the news68k binary distribution also has its own checksum files, just as the source distribution does. NetBSD/news68k System Requirements and Supported Devices NetBSD/news68k 2.1 will run on single m68030-based Sony NEWS worksta- tions. They include the NWS-14x0, NWS-15x0, PWS-15x0, NWS-17x0, and NWS-12x0 machines. NetBSD/news68k does not currently support m68020-based machines (NWS-700, NWS-800) nor I/O processor based machines (NWS-800, NWS-1800). NetBSD/news68k 2.1 does not support any framebuffers so you have to use serial console to install NetBSD/news68k. NetBSD/news68k 2.1 does not support SCSI on NWS-12x0 machines, so instal- lations on NWS-12x0 must use a remote NFS file system. MIPS based NEWS workstations (NWS-3xxx or NWS-5000) are supported by NetBSD/newsmips. Supported hardware o CPUs - 68020-based: none - 68030-based: NWS-12x0, NWS-14x0, NWS-15x0, PWS-15x0, NWS-17x0 o RS232 interfaces - built in Zilog 8530 Serial Communication Controllers (zsc) o Network interfaces - built in LANCE Ethernet (le) o SCSI interfaces - built in CXD1180 SCSI interface (si) - most SCSI devices If it's not on this list, there is no official support for it in this release. More information can also be found at the NetBSD/news68k home- page: http://www.NetBSD.org/Ports/news68k/ Getting the NetBSD System on to Useful Media Note: NetBSD/news68k 2.1 does not support any framebuffers (yet) so you have to use serial console on installation procedure. You will need to have a 1.44 MB floppy disk to boot off. You must put the boot floppy image onto this disk, which contains software to install NetBSD system. If you are using a UNIX -like system (such as NEWS-OS or other NetBSD machines) to write the floppy images to disks, you should use the dd(1) command to copy the file system image(s) (.fs file(s)) directly to the raw floppy disk. It is suggested that you read the dd(1) manual page or ask your system administrator to determine the correct set of arguments to use; it will be slightly different from system to system, and a com- prehensive list of the possibilities is beyond the scope of this docu- ment. If you have an i386 machine which runs MS-DOS and use them to write the floppy image(s) to floppy disk, you can use the rawrite utility, provided in the i386/installation/misc directory of the NetBSD distribution. It will write a file system image (.fs file) to a floppy disk. A rawrite32 is also available that runs under MS Windows. Though NetBSD/news68k uses the floppy disk to boot for the initial installation, the NetBSD/news68k kernel does not support the floppy device. Some other machines or systems are still required to write floppy images even after NetBSD/news68k has been installed. SCSI devices on NWS-12x0 machines are not supported (yet), so they can only run NetBSD/news68k diskless. No file transfer is needed, and all you have to do is to prepare files on the server. More information about diskless setting can be found at http://www.NetBSD.org/Documentation/network/netboot/ The NEWS PROM also supports tape boot and network boot, but NetBSD/news68k does not support them currently. After the boot floppy is prepared, just type bo fh on the PROM prompt to boot it. Note that if you are installing or upgrading from a writable media, the media can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted. Installation is supported from several media types, including: o CD-ROM / DVD o FTP o Remote NFS partition The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the var- ious media are outlined below. CD-ROM / DVD Find out where the distribution set files are on the CD- ROM or DVD. Likely locations are binary/sets and news68k/binary/sets. Proceed to the instruction on installation. FTP The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. If you don't have access to a functioning nameserver during installation, the IPv4 address of ftp.NetBSD.org is 204.152.184.75 and the IPv6 address is 2001:4f8:4:7:2e0:81ff:fe21:6563 (as of June, 2004). Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Note: This method of installation is recommended for those familiar with using BSD network configuration and management commands. If you aren't, this docu- mentation should help, but is not intended to be all-encompassing. NFS Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the /etc/exports file on of the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privileges on the server.) You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once the NFS server is set up properly and you have the information mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on pre- paring your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Note: This method of installation is recommended for those already familiar with using BSD network con- figuration and management commands. If you aren't, this documentation should help, but is not intended to be all-encompassing. Preparing your System for NetBSD installation First and foremost, before beginning the installation process, make sure you have a reliable backup of any data on your hard disk that you wish to keep. Mistakes in partitioning your hard disk may lead to data loss. Installing the NetBSD System Running the sysinst installation program 1. Introduction Using sysinst, installing NetBSD is a relatively easy process. You still should read this document and have it in hand when doing the installation process. This document tries to be a good guideline for the installation and as such covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. General The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installation system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst pro- gram from the command prompt. It is not necessary to reboot. 3. Quick install First, let's describe a quick install. The other sections of this document go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instruc- tions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. o What you need. - The distribution sets (in this example, they are on CD). - One 1.44 MB 3.5" floppy. - A CD-ROM drive (SCSI), a hard disk and a minimum of 4 MB of memory installed. - The hard disk should have at least 100 + n megabytes of space free, where n is the number of megabytes of main mem- ory in your system. If you wish to install the X Window System as well, you will need at least 120 MB more. o Creating the boot floppies. You can create the floppies needed for installation under MS-DOS or Windows. Supposing your 1.44 MB floppy drive is drive A:, and your CD is drive E: do the fol- lowing from an MS-DOS command prompt: e: cd \NetBSD-2.1\i386\installation\misc rawrite When asked for a source filename, answer \NetBSD-2.1\news68k\installation\floppy\boot.fs When asked for a destination drive answer `a'. o To create a bootfloppy under NetBSD or other UNIX -like system, you would type something like: # dd if=.../boot1.fs bs=18k of=/dev/rfd0a o The Quick Installation - Insert the first boot floppy you just created. Boot the computer. Type NEWS bo fh After language selection, the main menu will be displayed. .***********************************************. * NetBSD-2.0 Install System * * * *a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * x: Exit Install System * .***********************************************. - If you wish, you can configure some network settings immedi- ately by choosing the Utility menu and then Configure network. It isn't actually required at this point, but it may be more convenient. Go back to the main menu. - Choose install. - You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. - After your disk has been prepared, choose CD-ROM as the medium. The default values for the path and device should be ok. - After all the files have been unpacked, go back to the main menu and select reboot, after you have removed the boot- floppy from the drive. - NetBSD will now boot. If you haven't already done so in sysinst, you should log in as root, and set a password for that account. You are also advised to edit the file /etc/rc.conf to match your system needs. - Your installation is now complete. - For configuring the X window system, if installed, see the files in /usr/X11R6/lib/X11/doc. Further information can be found on http://www.xfree86.org/. 4. Booting NetBSD Boot your machine. The boot loader will start, and will print a countdown and begin booting. If the boot loader messages do not appear in a reasonable amount of time, you either have a bad boot floppy or a hardware problem. Try writing the install floppy image to a different disk, and using that. It will take a while to load the kernel from the floppy, probably around a minute or so, then, the kernel boot messages will be dis- played. This may take a little while also, as NetBSD will be prob- ing your system to discover which hardware devices are installed. The most important thing to know is that wd0 is NetBSD 's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc. Note that once the system has finished booting, you need not leave the floppy in the disk drive. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 5. Network configuration If you will not use network operation during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu, and select the Configure network option. If you only want to temporarily use net- working during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response in reply to answers relating to this. 6. Installation drive selection and parameters To start the installation, select Install NetBSD to hard disk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. Depending on how many disks are found, you may get a different message. You should see disk names like sd0 or sd1. 7. Partitioning the disk o Which portion of the disk to use. You will be asked if you want to use the entire disk or only part of the disk. If you decide to use the entire disk for NetBSD, it will be checked if there are already other systems present on the disk, and you will be asked to confirm whether you want to overwrite these. 8. Editing the NetBSD disklabel The partition table of the NetBSD part of a disk is called a disklabel. There are 4 layouts for the NetBSD part of the disk that you can pick from: Standard, Standard with X, Custom and Use Existing. The first two use a set of default values (that you can change) suitable for a normal installation, possibly including X. With the Custom option you can specify everything yourself. The last option uses the partition info already present on the disk. You will be presented with the current layout of the NetBSD diskla- bel, and given a chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap partition has a special type called swap. Some partitions in the disklabel have a fixed purpose. a Root partition (/) b Swap partition. c The NetBSD portion of the disk. d-h Available for other use. Traditionally, g is the par- tition mounted on /usr, but this is historical prac- tice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it something different, make sure the name is a single word and con- tains no special characters. You don't need to remember this name. 9. Preparing your hard disk You are now at the point of no return. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to pro- ceed, enter yes at the prompt. The install program will now label your disk and make the file sys- tems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are running. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Otherwise, you can continue the installa- tion program after pressing the return key. 10. Getting the distribution sets The NetBSD distribution consists of a number of sets, that come in the form of gzipped tarfiles. A few sets must be installed for a working system, others are optional. At this point of the installa- tion, you will be presented with a menu which enables you to choose from one of the following methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 11. Installation using ftp To be able to install using ftp, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these ques- tions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the ftp server. sysinst will proceed to transfer all the default set files from the remote site to your hard disk. 12. Installation using NFS To be able to install using NFS, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these ques- tions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e. correctly exported to your machine. If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the NFS server. 13. Installation from CD-ROM When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM player (usually cd0), and the directory name on the CD-ROM where the distribution files are. sysinst will then check if the files are indeed available in the specified location, and proceed to the actual extraction of the sets. 14. Installation from an unmounted file system In order to install from a local file system, you will need to spec- ify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location. 15. Installation from a local directory This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file sys- tem that is already accessible. sysinst will ask you for the name of this directory. 16. Extracting the distribution sets After the install sets containing the NetBSD distribution have been made available, you can either extract all the sets (a full instal- lation), or only extract sets that you have selected. In the latter case, you will be shown the currently selected sets, and given the opportunity to select the sets you want. Some sets always need to be installed (kern, base) and etc they will not be shown in this selection menu. Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably, especially on machines with slow graphics consoles or serial consoles. After all the files have been extracted, all the necessary device node files will be created. If you have already configured network- ing, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the net- work configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can than set a password for the "root" account, to prevent the machine coming up without access restric- tions. 17. Finalizing your installation Congratulations, you have successfully installed NetBSD 2.1. You can now reboot the machine, and boot NetBSD from hard disk. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state, with the most important ones described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the sys- tem asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi- user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). If your /usr directory is on a separate partition and you do not know how to use ed, you will have to mount your /usr partition to gain access to ex or vi. Do the following: # mount /usr # export TERM=vt220 If you have /var on a separate partition, you need to repeat that step for it. After that, you can edit /etc/rc.conf with vi(1). When you have finished, type exit at the prompt to leave the single- user shell and continue with the multi-user boot. Other values that need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute, furthermore add an ifconfig_int for your network interface, along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. If you're using the machine in a networked environment, you should cre- ate an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. Unless you have connected an unusual terminal device as the console you can just press RETURN when it prompts for Terminal type? [...]. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you have installed the X Window System, look at the files in /usr/X11R6/lib/X11/doc for information. Don't forget to add /usr/X11R6/bin to your path in your shell's dot file so that you have access to the X binaries. 5. Installing third party packages If you wish to install any of the software freely available for UNIX -like systems you are strongly advised to first check the NetBSD package system. This automatically handles any changes necessary to make the software run on NetBSD, retrieval and installation of any other packages on which the software may depend, and simplifies installation (and deinstallation), both from source and precompiled binaries. o More information on the package system is at http://www.NetBSD.org/Documentation/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc/README.html o Precompiled binaries can be found at ,: ftp://ftp.NetBSD.org/pub/NetBSD/packages/ usually in the 2.1/news68k/All subdir. You can install them with the following commands under sh(1): # PKG_PATH=ftp://ftp.NetBSD.org/pub/NetBSD/packages/2.1/news68k/All # export PKG_PATH # pkg_add -v tcsh # pkg_add -v bash # pkg_add -v perl # pkg_add -v apache # pkg_add -v kde # pkg_add -v mozilla ... If you are using csh(1) then replace the first two lines with the following: # setenv PKG_PATH ftp://ftp.NetBSD.org/pub/NetBSD/packages/2.1/news68k/All ... The above commands will install the Tenex-csh and Bourne Again shell, the Perl programming language, Apache web server, KDE desktop environment and the Mozilla web browser as well as all the packages they depend on. o Package sources for compiling packages on your own can be obtained by retrieving the file ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-current/tar_files/pkgsrc.tar.gz They are typically extracted into /usr/pkgsrc (though other locations work fine), with the commands: # mkdir /usr/pkgsrc # ( cd /usr/pkgsrc ; tar -zxpf - ) pkgsrc.tar.gz After extracting, see the README and doc/pkgsrc.txt files in the extraction directory (e.g. /usr/pkgsrc/README) for more infor- mation. 6. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/mail/sendmail.cf file will almost definitely need to be adjusted; files aiding in this can be found in /usr/share/sendmail. See the README file there for more infor- mation. If you prefer postfix as MTA, adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the man- ual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System The upgrade to NetBSD 2.1 is a binary upgrade; it can be quite difficult to update the system from an earlier version by recompiling from source, primarily due to interdependencies in the various components. To do the upgrade, you must have the boot floppy available. You must also have at least the base and kern binary distribution sets available, so that you can upgrade with them, using one of the upgrade methods described above. Finally, you must have sufficient disk space available to install the new binaries. Since files already installed on the system are overwritten in place, you only need additional free space for files which weren't previously installed or to account for growth of the sets between releases. If you have a few megabytes free on each of your root (/) and /usr partitions, you should have enough space. Since upgrading involves replacing the kernel, the boot blocks on your NetBSD partition, and most of the system binaries, it has the potential to cause data loss. You are strongly advised to back up any important data on the NetBSD partition or on another operating system's partition on your disk before beginning the upgrade process. The upgrade procedure using the sysinst tool is similar to an installa- tion, but without the hard disk partitioning. sysinst will attempt to merge the settings stored in your /etc directory with the new version of NetBSD. Getting the binary sets is done in the same manner as the installation procedure; refer to the installation part of the document for how to do this. Also, some sanity checks are done, i.e. file sys- tems are checked before unpacking the sets. After a new kernel has been copied to your hard disk, your machine is a complete NetBSD 2.1 system. However, that doesn't mean that you're fin- ished with the upgrade process. You will probably want to update the set of device nodes you have in /dev. If you've changed the contents of /dev by hand, you will need to be careful about this, but if not, you can just cd into /dev, and run the command: # sh MAKEDEV all Finally, you will want to delete old binaries that were part of the ver- sion of NetBSD that you upgraded from and have since been removed from the NetBSD distribution. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 2.1. Issues affecting an upgrade from NetBSD 1.6 The following issues can generally be resolved by extracting the etc set into a temporary directory and running postinstall: mkdir /tmp/upgrade cd /tmp/upgrade pax -zrpe -f /path/to/etc.tgz ./etc/postinstall -s `pwd` check ./etc/postinstall -s `pwd` fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* o The following files are now obsolete: /etc/rc.d/fsck.sh /etc/rc.d/gated /etc/rc.d/kerberos /etc/rc.d/NETWORK /etc/rc.d/systemfs /etc/rc.d/xntpd and /etc/rc.d/ypset. o The users and groups `smmsp', needs to be created, `news' is no longer part of the system. The following issues need to be resolved manually: o postfix(8) configuration files require upgrading. cd /usr/share/examples/postfix cp post-install postfix-files postfix-script /etc/postfix postfix check Using online NetBSD documentation Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are o intro(1), o man(1), o apropros(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter # man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: netbsd-bugs@NetBSD.org. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/MailingLists/. If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-help@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encouragement. o The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. o The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. o The Helsinki University of Technology in Finland for hosting the NetBSD backup CVS and backup server. o SSH Communications Security in Finland for operating the backup server. o The many organisations that provide NetBSD mirror sites. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o The following individuals and organizations (each in alphabetical order) have made donations or loans of hardware and/or money, to sup- port NetBSD development, and deserve credit for it: AboveNet Communications, Inc. Advanced System Products, Inc. Alex Poylisher Alistair Crooks Andrew Brown Atsushi YOKOYAMA Avalon Computer Systems Bay Area Internet Solutions Ben Collver Bill Coldwell Bill Sommerfeld Brad Salai Brains Corporation, Japan Brian Carlstrom Brian McGroarty Canada Connect Corporation Castor Fu Central Iowa (Model) Railroad Charles Conn Charles D. Cranor Charles M. Hannum Chris Legrow Christer O. Andersson Christopher g. Demetriou Christos Zoulas Chuck Silvers Co-operative Research Centre for Enterprise Distributed Curt Sampson Dave Burgess Dave Rand David Brownlee Demon Internet, UK Derek Fellion Digital Equipment Corporation Distributed Processing Technology Douglas J. Trainor Easynet, UK Ed Braaten Edward Richley Eric and Rosemary Spahr Free Hardware Foundation Greg Gingerich Guenther Grau Harald Koerfgen Harry McDonald Heiko W. Rupp Herb Peyerl Hubert Feyrer Innovation Development Enterprises of America Internet Software Consortium James Chacon Jan Joris Vereijken Jason Birnschein Jason Brazile Jason R. Thorpe Jim Wise John Kohl Jonathan P. Kay Jordan K. Hubbard Kenneth Alan Hornstein Kevin Keith Woo Kimmo Suominen Krister Waldfridsson Lex Wennmacher LinuxFest Northwest Luke Mewburn MS Macro System GmbH, Germany Mark Brinicombe Mark S. Thomas Mason Loring Bliss Mattias Karlsson Michael Graff Michael L. Hitch Michael Richardson Michael Thompson Michael W. James Mike Price Neil J. McRae Noah M. Keiserman Norman R. McBride Numerical Aerospace Simulation Facility, NASA Ames Research Oliver Cahagne Perry E. Metzger Petri T. Koistinen Piermont Information Systems Inc. Precedence Technologies Ltd Ralph Campbell Reinoud Zandijk Richard Nelson Rob Windsor Ross Harvey SDF Public Access Unix, Inc. 501(c)(7) Salient Systems Inc. Scott Ellis Scott Kaplan Simon Burge Soren Jacobsen Soren Jorvang Steve Allen Steve Wadlow SunROOT# Project Ted Lemon Ted Spradley Thor Lancelot Simon Tim Law Tom Coulter Toru Nishimura VMC Harald Frank, Germany Warped Communications, Inc. Wasabi Systems Whitecross Database Systems Ltd. William Gnadt Worria Web Hosting (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Allen Briggs briggs@NetBSD.org Matt Thomas matt@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): ~ Allen Briggs briggs@NetBSD.org sandpoint Anders Magnusson ragge@NetBSD.org vax Andrey Petrov petrov@NetBSD.org sparc64 Ben Harris bjh21@NetBSD.org acorn26 Chris Gilbert chris@NetBSD.org cats Christian Limpach cl@NetBSD.org xen Eduardo Horvath eeh@NetBSD.org evbppc Frank van der Linden fvdl@NetBSD.org amd64 Frank van der Linden fvdl@NetBSD.org i386 Gavan Fantom gavan@NetBSD.org iyonix IWAMOTO Toshihiro toshii@NetBSD.org hpcarm Ichiro Fukuhara ichiro@NetBSD.org hpcarm Ignatios Souvatzis is@NetBSD.org amiga Izumi Tsutsui tsutsui@NetBSD.org hp300 Izumi Tsutsui tsutsui@NetBSD.org news68k Jason Thorpe thorpej@NetBSD.org algor Jason Thorpe thorpej@NetBSD.org evbarm Jason Thorpe thorpej@NetBSD.org shark Jeremy Cooper jeremy@NetBSD.org sun3 Jonathan Stone jonathan@NetBSD.org pmax Julian Coleman jdc@NetBSD.org atari Jun-ichiro itojun Hagino itojun@NetBSD.org evbsh3 Jun-ichiro itojun Hagino itojun@NetBSD.org mmeye Kazuki Sakamoto sakamoto@NetBSD.org bebox Lennart Augustsson augustss@NetBSD.org pmppc Marcus Comstedt marcus@NetBSD.org dreamcast Martin Husemann martin@NetBSD.org sparc64 Matt DeBergalis deberg@NetBSD.org next68k Matt Fredette fredette@NetBSD.org hp700 Matt Fredette fredette@NetBSD.org sun2 Matt Thomas matt@NetBSD.org alpha Matt Thomas matt@NetBSD.org netwinder Matthias Drochner drochner@NetBSD.org cesfic NISHIMURA Takeshi nsmrtks@NetBSD.org x68k NONAKA Kimihiro nonaka@NetBSD.org prep Nathan Williams nathanw@NetBSD.org sun3 Noriyuki Soda soda@NetBSD.org arc Paul Kranenburg pk@NetBSD.org sparc Phil Nelson phil@NetBSD.org pc532 Reinoud Zandijk reinoud@NetBSD.org acorn32 Ross Harvey ross@NetBSD.org alpha Soren Jorvang soren@NetBSD.org cobalt Soren Jorvang soren@NetBSD.org sgimips Scott Reynolds scottr@NetBSD.org mac68k Shin Takemura takemura@NetBSD.org hpcmips Simon Burge simonb@NetBSD.org evbmips Simon Burge simonb@NetBSD.org evbppc Simon Burge simonb@NetBSD.org pmax Simon Burge simonb@NetBSD.org sbmips Steve Woodford scw@NetBSD.org evbsh5 Steve Woodford scw@NetBSD.org mvme68k Steve Woodford scw@NetBSD.org mvmeppc Tohru Nishimura nisimura@NetBSD.org luna68k Tsubai Masanari tsubai@NetBSD.org macppc Tsubai Masanari tsubai@NetBSD.org newsmips UCHIYAMA Yasushi uch@NetBSD.org hpcsh UCHIYAMA Yasushi uch@NetBSD.org playstation2 Wayne Knowles wdk@NetBSD.org mipsco Wolfgang Solfrank ws@NetBSD.org ofppc The NetBSD 2.1 Release Engineering team: Grant Beattie grant@NetBSD.org Erik Berls cyber@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Havard Eidnes he@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org Soren Jacobsen snj@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Luke Mewburn lukem@NetBSD.org Jeff Rizzo riz@NetBSD.org Matthias Scheler tron@NetBSD.org Curt Sampson cjs@NetBSD.org Jim Wise jwise@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Christoph Badura bad@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Grant Beattie grant@NetBSD.org Jason Beegan jtb@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Mason Loring Bliss mason@NetBSD.org Charles Blundell cb@NetBSD.org Rafal Boni rafal@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org John Brezak brezak@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Frederick Bruckman fredb@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Dave Carrel carrel@NetBSD.org Daniel Carosone dan@NetBSD.org James Chacon jmc@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Ben Collver ben@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Aidan Cully aidan@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Matt DeBergalis deberg@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Elad Efrat elad@NetBSD.org Havard Eidnes he@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Adam Glass glass@NetBSD.org Michael Graff explorer@NetBSD.org Brian C. Grayson bgrayson@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Ben Harris bjh21@NetBSD.org Ross Harvey ross@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org HAYAKAWA Koichi haya@NetBSD.org John Heasley heas@NetBSD.org Rene Hexel rh@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Christian E. Hopps chopps@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hornquist Astrand lha@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Chris Jones cjones@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Antti Kantee pooka@NetBSD.org Masanori Kanaoka kanaoka@NetBSD.org Mattias Karlsson keihan@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Mario Kemper magick@NetBSD.org Min Sik Kim minskim@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org John Kohl jtk@NetBSD.org Daniel de Kok daniel@NetBSD.org Paul Kranenburg pk@NetBSD.org Martti Kuparinen martti@NetBSD.org Kentaro A. Kurahone kurahone@NetBSD.org Kevin Lahey kml@NetBSD.org Johnny C. Lam jlam@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org Paul Mackerras paulus@NetBSD.org Anders Magnusson ragge@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org David Maxwell david@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Perry Metzger perry@NetBSD.org Simas Mockevicius symka@NetBSD.org Juan Romero Pardines xtraeme@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Minoura Makoto minoura@NetBSD.org Luke Mewburn lukem@NetBSD.org der Mouse mouse@NetBSD.org Joseph Myers jsm@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Phil Nelson phil@NetBSD.org Bob Nestor rnestor@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Jonathan Perkin sketch@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Rui Paulo rpaulo@NetBSD.org Peter Postma peter@NetBSD.org Dante Profeta dante@NetBSD.org Chris Provenzano proven@NetBSD.org Niels Provos provos@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Michael Richardson mcr@NetBSD.org Tim Rightnour garbled@NetBSD.org Jeff Rizzo riz@NetBSD.org Gordon Ross gwr@NetBSD.org Steve Rumble rumble@NetBSD.org Ilpo Ruotsalainen lonewolf@NetBSD.org Heiko W. Rupp hwr@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Takeshi Shibagaki shiba@NetBSD.org Naoto Shimazaki igy@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org SOMEYA Yoshihiko someya@NetBSD.org Bill Sommerfeld sommerfeld@NetBSD.org Ignatios Souvatzis is@NetBSD.org Bill Squier groo@NetBSD.org Jonathan Stone jonathan@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org SUNAGAWA Keiki kei@NetBSD.org Kimmo Suominen kim@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Ian Lance Taylor ian@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Todd Whitesel toddpw@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Dan Winship danw@NetBSD.org Jim Wise jwise@NetBSD.org Michael Wolfson mbw@NetBSD.org Steve Woodford scw@NetBSD.org Colin Wood ender@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Maria Zevenhoven maria7@NetBSD.org Christos Zoulas christos@NetBSD.org Other contributors: Dave Burgess burgess@cynjut.infonet.net Brian R. Gaeke brg@dgate.org Brad Grantham grantham@tenon.com Lawrence Kesteloot kesteloo@cs.unc.edu Waldi Ravens waldi@moacs.indiv.nl.net Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trade- marks of their respective owners. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product contains software developed by Ignatios Souvatzis for the NetBSD project. This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project. This product contains software written by Michael L. Hitch for the NetBSD project. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) This product includes cryptographic software written by Eric Young (eay@mincom.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Division, US Naval Research Laboratory. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Gordon W. Ross and Leo Wep- pelman. This product includes software developed by Hellmuth Michaelis and Joerg Wunsch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Uni- versity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Alistair G. Crooks. This product includes software developed by Alistair G. Crooks. for the NetBSD project. This product includes software developed by Allen Briggs This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brad Pepers This product includes software developed by Bradley A. Grantham. This product includes software developed by Brini. This product includes software developed by Causality Limited. This product includes software developed by Charles D. Cranor and Seth Widoff. This product includes software developed by Charles D. Cranor and Wash- ington University. This product includes software developed by Charles D. Cranor, Washington University, and the University of California, Berkeley and its contribu- tors. This product includes software developed by Charles D. Cranor, Washington University, the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christian Limpach This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Cybernet Corporation and Nan Yang Computer Services Limited This product includes software developed by Daishi Kato This product includes software developed by Dale Rahn. This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Darrin B. Jewell This product includes software developed by David Miller. This product includes software developed by Dean Huxley. This product includes software developed by Eduardo Horvath. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@min- com.oz.au) This product includes software developed by Eric Young (eay@crypt- soft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by Ezra Story and by Kari Met- tinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Gordon W. Ross This product includes software developed by HAYAKAWA Koichi. This product includes software developed by Harvard University and its contributors. This product includes software developed by Harvard University. This product includes software developed by Herb Peyerl. This product includes software developed by Hubert Feyrer for the NetBSD Project. This product includes software developed by Iain Hibbert This product includes software developed by Ian F. Darwin and others. This product includes software developed by Ian W. Dall. This product includes software developed by Ichiro FUKUHARA. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jared D. McNeill. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/ This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Jukka Marin. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berke- ley and its contributors. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Leo Weppelman for the NetBSD Project. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Luke Mewburn. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Manuel Bouyer. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Murray This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Solfrank. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Mats O Jansson and Charles D. Cranor. This product includes software developed by Mats O Jansson. This product includes software developed by Matt DeBergalis This product includes software developed by Matthew Fredette. This product includes software developed by Matthias Pfaller. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Michael Graff. This product includes software developed by Michael L. Hitch. This product includes software developed by Michael Shalayeff. This product includes software developed by Michael Smith. This product includes software developed by Mike Glover and contributors. This product includes software developed by Mike Pritchard. This product includes software developed by Minoura Makoto. This product includes software developed by Nan Yang Computer Services Limited. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Onno van der Linden. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by Philip L. Budne. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Roland C. Dowdeswell. This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Soren S. Jorvang. This product includes software developed by Stephan Thesing. This product includes software developed by Steve Woodford. This product includes software developed by Takashi Hamada This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by Tetsuya Isaki. This product includes software developed by Thomas Gerner This product includes software developed by Thomas Klausner for the NetBSD Project. This product includes software developed by Tobias Weingartner. This product includes software developed by Todd C. Miller. This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project. This product includes software developed by Tohru Nishimura for the NetBSD Project. This product includes software developed by Tohru Nishimura. for the NetBSD Project. This product includes software developed by TooLs GmbH. This product includes software developed by Toru Nishimura. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contrib- utors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the Charles D. Cranor, Wash- ington University, University of California, Berkeley and its contribu- tors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Kungliga Tekniska Hogskolan and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) his product includes software developed by the PocketBSD project and its contributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Develop- ment Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia Uni- versity. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Labora- tory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Chris- tos Zoulas This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Igna- tios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Michael L. Hitch. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden This product includes software developed for the NetBSD Project by Alle- gro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Labora- tory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). The End NetBSD August 23, 2005 NetBSD