INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL -- Installation procedure for NetBSD/atari. CONTENTS About this Document............................................2 What is NetBSD?................................................2 Changes Between The NetBSD 2.0 and 3.0 Releases................3 Supported platforms and machines............................3 Supported devices...........................................3 Kernel......................................................5 Networking..................................................5 File system.................................................6 Libraries...................................................6 Security....................................................6 System administration and user tools........................7 Miscellaneous...............................................7 atari specific..............................................7 The Future of NetBSD...........................................8 Sources of NetBSD..............................................8 NetBSD 3.0 Release Contents....................................8 NetBSD/atari subdirectory structure........................10 Binary distribution sets...................................10 NetBSD/atari System Requirements and Supported Devices........13 Supported devices..........................................13 Getting the NetBSD System on to Useful Media..................14 Preparing your System for NetBSD installation.................15 Preparing your hard disk for the NetBSD installation.......15 Booting the installer on an existing system................16 Booting the installer on new systems.......................16 Using loadbsd.ttp..........................................17 Installing the NetBSD System..................................17 Running the sysinst installation program...................17 Introduction............................................17 General.................................................18 Quick install...........................................18 Booting NetBSD..........................................19 Network configuration...................................19 Installation drive selection and parameters.............19 Partitioning the disk...................................20 Preparing your hard disk................................21 Getting the distribution sets...........................21 Installation using ftp..................................21 Installation using NFS..................................21 Installation from CD-ROM................................22 Installation from an unmounted file system..............22 Installation from a local directory.....................22 Extracting the distribution sets........................22 Finalizing your installation............................22 Post installation steps.......................................23 Upgrading a previously-installed NetBSD System................25 Compatibility Issues With Previous NetBSD Releases............26 Issues affecting an upgrade from NetBSD 2.1 and older......26 Using online NetBSD documentation.............................26 Administrivia.................................................27 Thanks go to..................................................28 We are........................................................33 Legal Mumbo-Jumbo.............................................38 The End.......................................................44 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 3.0 on the atari platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX -like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX -like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on fifty four different system architectures (ports), featuring sev- enteen machine architectures across fifteen distinct CPU families, and is being ported to more. The NetBSD 3.0 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distri- bution. For information on them, please see the NetBSD web site at .: http://www.NetBSD.org/) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Changes Between The NetBSD 2.0 and 3.0 Releases The NetBSD 3.0 release provides numerous significant functional enhance- ments, including support for many new devices, integration of hundreds of bug fixes, new and updated kernel subsystems, and many user-land enhance- ments. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize a year of development that went into the NetBSD 3.0 release. Some highlights include: Supported platforms and machines o A port to new platform: iyonix. The iyonix port supports the Iyonix PC, which is a desktop computer from Castle Technology, based on a 600MHz XScale 80321 processor. o The xen port now supports Xen 2.0, both in privileged and unprivi- leged mode. o The evbarm port has support for the TS-7200 single board computer, which is also known as ``the NetBSD Controlled Toaster''. o The sgimips port now supports IP12 (Personal Iris 4D/30, 4D/35, and Indigo R3K) machines. o The PowerPC 601 support has been added, and the prep port now sup- ports IBM RS/6000 60P 7020-011. Supported devices o Added iteide(4): driver for ITE 8212 IDE controller. o Added ixpide(4): driver for ATI IXP series chipset IDE controller. o Added pdcsata(4): driver for Promise SATA150 (aka PDC203xx) con- trollers. o Added ipw(4): driver for Intel PRO/Wireless 2100. o Added iwi(4): driver for Intel PRO/Wireless 2200AG/2915ABG. o Added rtw(4): driver for Realtek RTL8180L IEEE 802.11b wireless net- work. o Added vge(4): driver for VIA VT612X Gigabit Ethernet controller. o Added xge(4): driver for Neterion Xframe-I 10 gigabit Ethernet. o Added cdce(4): driver for CDC USB Ethernet. o Added atu(4): driver for Atmel AT76C50x based 802.11b wireless net- work interfaces. o Added uep(4): driver for eGalax USB touchpanel controller. o Added ugensa(4): driver for USB generic serial adapter, which cur- rently supports CDMA Wireless PC Card. o Added auixp(4): driver for ATI IXP series chipset audio controller. o Added auacer(4): driver for ALi M5455 audio controller. o Added azalia(4): driver for High Definition Audio controller. o Added spif(4): driver for Sun SUNW,spif multi-port Sbus card. o viaide(4) now supports nForce2 Ultra 400, nForce3 250 IDE and SATA, and nForce4 IDE and SATA controllers. viaide(4) also supports VIA VT6421 SATA RAID controller though drives on the controller need to be configured into RAID/JOBS sets via its BIOS. o siside(4) now supports SiS 180 and 741 SATA controllers. o artsata(4), which is the Intel i31244 Serial ATA disk controller driver, now supports DPA mode. o satalink(4) now supports Silicon Image 3512 SATA. o piixide(4) now supports Intel 82801FB/FR (ICH6/6R) IDE and SATA, 82801FBM SATA, 82801G (ICH7) IDE and SATA, and i6300ESB IDE and SATA controllers. Also added basic support for RAID0 and RAID1 for the Adaptec HostRAID format as found on the Intel 6300ESB on-board RAID. o stge(4) now works on big-endian machines including sparc64 with hard- ware checksums. o aac(4) now supports Adaptec SATA RAID 2810SA. o mpt(4) now supports LSI Logic FC919x SCSI controllers. o spc(4) now has support for Fujitsu MB87030-based PCMCIA SCSI con- troller. o bge(4) now supports Broadcom BCM5788, BCM5705K, BCM5721, and BCM5751M Gigabit Ethernet controllers, and has 802.3x flow control support. o gem(4) and hme(4) now have hardware checksums support. o re(4) and wm(4) now supports TCPv4 hardware transmit segment offload. o wm(4) now supports more Intel Gigabit Ethernet chips and 64bit PCI DMA transfer, o re(4) now supports Corega CG-LAPCIGT Gigabit Ethernet, and RTL8169 based CardBus Ethernet interfaces, including NetGear GA-511. o ex(4) now supports 3Com 3c920B-EMB-WNM Integrated Fast Ethernet. o sk(4) now supports Belkin Gigabit Desktop Network card. o bce(4) now supports Broadcom BCM4401-B0 Ethernet. o tl(4) now supports Compaq Netelligent 10 T/2 PCI UTP/Coax Controller. o wi(4) now supports SMC2531W-B EliteConnect Wireless Adapter. o fxp(4) now supports Intel 82801FB (ICH6) 10/100 Ethernet. o tlp(4) now supports LinkSys PCMPC200 Cardbus Ethernet and ASIX AX88140A/AX88141 chipsets. o Many improvements for atw(4) ADMtek ADM8211 802.11 wireless network driver. o auich(4) now supports nForce2 Ultra 400, nForce3 250 MCP-T AC-97, nForce4, Intel ICH7, and Intel 6300ESB audio controllers. o auvia(4) now supports suspend and resume. o puc(4) now supports VS-Com PCI-210H 2S/1P card, VScom PCI-200 2S card, and ADDI-DATA APCI-7800 8-port serial adapter. o uftdi(4) now supports Sealevel Systems' uftdi-based USB-Serial adapter. o uvscom(4) now supports SUNTAC U-Cable type A4 USB serial adapter. o pms(4) now supports synaptics touchpad. o lm(4) now supports iTE IT8705f and Winbond 83627THF environment moni- tor controllers. o Many bug fixes and improvements for ehci(4) USB 2.0 controllers. o Many fixes for uaudio(4) devices. o uax(4) ASIX AX88172 USB Ethernet driver has been replaced by axe(4) driver derived from FreeBSD. o vnd(4) pseudo-device now support compressed image. Kernel o The i386 port now supports the Enhanced SpeedStep Technology. o Added statvfs(2) family of system calls. o Added ptm(4), pty/98 pty multiplexor device. o Added swwdog(4), a software watchdog timer facility. o Autoconfiguration framework is rewritten for device driver LKMs. o compat_darwin(8) emulation now supports MacOS X.3 binaries. o sparc64 and shark ports have switched to wscons(9), the machine-inde- pendent console framework. Additionally sparc64 port switched to a XFree86 based X server and now supports the cg6, mach64 and ffb/afb framebuffers with acceleration. o Added new pselect(2) and pollts(2) synchronous I/O multiplexing sys- tem calls. o Added another experimental buffer queue strategy, BUFQ_PRIOCSCAN, Per-priority cyclical scan. Note the existing strategy NEW_BUFQ_STRATEGY is renamed to BUFQ_READPRIO, since that gives pri- ority to issuing read requests over write requests. o The way to allocate a kernel structure, map entry, was improved so that it doesn't need preliminary knowledge of system load, i.e. users no longer have to define ``options MAX_KMAPENT'' in their kernel con- figurations even on busy servers. Networking o TCP now supports TCP Selective Acknowledgement Options (RFC 2018) for enhanced performance especially on long distance connections and TCP MD5 signatures (RFC 2385) for enhanced protection against attacks. o TCP can take advantage of hardware-assisted TCP/IPv4 segmentation on re(4), wm(4) and xge(4) interfaces. o The OpenBSD Packet Filter has been integrated as alternative packet filter solution. o IP Filter has been upgraded to version 4.1.8. o The KAME IPsec stack now supports ESP over NAT connections (RFC 3948). o IPv4 Protocol Independent Multicast (PIM) routing support has been added. o ipsec-tools 0.6.3 provide IKE support for ESP over NAT connections (RFC 3947), user authentication via XAuth and automatic network con- figurations of VPN clients via Mode Config. o Added RFC 3378 EtherIP support, which makes it possible to add gif(4) interface to bridges. o Added tap(4), the virtual Ethernet device. o ppp(4) has been updated to 2.4.3. o gre(4) now supports tunneling of the IPv6 Protocol. File system o UFS_DIRHASH support has been added from FreeBSD, which increase lookup performance by maintaining in-core hash tables for large directories on UFS. o fss(4), file system snapshot support has been added. o Added ptyfs, pseudo-terminal file system. o CD9660 file system now supports UTF-8 filename on Joliet extension. o Ext2fs now supports large files (larger than 2G bytes). fsck_ext2fs(8) also handles them and supports conversion from old file systems. o The stability of the LFS file system has been improved. Libraries o Added PAM (Pluggable Authentication Modules framework). o Support wide strings in C++. o Re-entrant library functions like getpwent_r() have been added. o Some libc string functions for i386 have been replaced with optimized version. o Added DCE 1.1 RPC compatible UUID (Universally Unique Identifier) routines to libc. o Added memmem(3) to libc, which is API compatible with the functions in FreeBSD and Linux. Security o The Veriexec framework is now using hash tables to store per-file data, resulting in much faster operation. It supports four different enforcement levels and full control over verbosity. Signature files are easier to generate and are more flexible than in the previous version. o Added SHA2 to libc to provide more secure hashing algorithms and made cksum(1) and mtree(8) support them. System administration and user tools o Various improvements for the ``sysinst'' installation program, including Spanish language translation. o Numerous improvements for syslogd(8), mostly from FreeBSD. o fsck(8) now has a progress meter option. o dump(8) now supports file system snapshots. o Added sockstat(1), which lists open sockets. o Added seq(1), a utility which prints a sequence of numbers, derived from Plan 9. Miscellaneous o audio(9) interface is improved. Added capability of audio software filter pipeline, which makes it easy for hardware drivers to add encoding support or sample rates support. o Updates of most third party packages that are shipped in the base system to the following latest stable releases: - am-utils 6.1-rc2 - BIND 9.3.0 - binutils 2.15-20041204 - cvs 1.11.20 - file 4.13 - gcc 3.3.3 - groff 1.19.1 - OpenSSH 3.9 - OpenSSL 0.9.7d - Postfix 2.1.5 - sendmail 8.13.3 - tcpdump 3.8.3 - texinfo 4.7 - tzdata2005o - XFree86 4.5.0 o Many new packages in the pkgsrc system, including the latest open source desktop KDE3, OpenOffice, perl, Apache and many more. At the time of writing, there are over 5400 third party packages available in pkgsrc. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. atari specific The atari release was imported into NetBSD in in March 1995. The first major release was NetBSD 1.1. About a year later, NetBSD 1.2 was released for the Atari. This release fixed a large number of bugs and made the Atari-port a stable member of the NetBSD family. The saga con- tinued with the NetBSD 1.3 release. In this release, support was added for the Medusa Hades, Riebl ethernet and Falcon IDE support. NetBSD 1.4 was released in 1999, and added support for various devices. NetBSD 1.5 was released in late 2000, NetBSD 1.6 was released in 2002, NetBSD 2.0 was released in 2004. And now, NetBSD 3.0 is emerging! The Future of NetBSD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: o providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. o providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. o providing a better position from which to undertake promotional activities. o periodically organizing workshops for developers and other interested people to discuss ongoing work. We intend to begin narrowing the time delay between releases. Our ambi- tion is to provide a full release every six to eight months. We hope to support even more hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the usability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. Sources of NetBSD Refer to .: http://www.NetBSD.org/mirrors/ NetBSD 3.0 Release Contents The root directory of the NetBSD 3.0 release is organized as follows: .../NetBSD-3.0/ CHANGES Changes since earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 3.0 distribution. README.files README describing the distribution's contents. TODO NetBSD 's todo list (also somewhat incomplete and out of date). patches/ Post-release source code patches. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 3.0 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. 79 MB gzipped, 367 MB uncompressed pkgsrc This set contains the ``pkgsrc'' sources, which contain the in- frastructure to build third-party packages. 24 MB gzipped, 200 MB uncompressed sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. 5 MB gzipped, 20 MB uncompressed src This set contains all of the base NetBSD 3.0 sources which are not in gnusrc, sharesrc, or syssrc. 37 MB gzipped, 176 MB uncompressed syssrc This set contains the sources to the NetBSD 3.0 kernel for all architectures; config(8); and dbsym(8). 26 MB gzipped, 140 MB uncompressed xsrc This set contains the sources to the X Window System. 84 MB gzipped, 450 MB uncompressed All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # ( cd / ; tar -zxpf - ) set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: BSDSUM Historic BSD checksums for the various files in that directory, in the format produced by the command: cksum -o 1 file. CKSUM POSIX checksums for the various files in that directory, in the format produced by the command: cksum file. MD5 MD5 digests for the various files in that directory, in the format produced by the command: cksum -m file. SYSVSUM Historic ATT System V UNIX checksums for the various files in that directory, in the format produced by the command: cksum -o 2 file. The MD5 digest is the safest checksum, followed by the POSIX checksum. The other two checksums are provided only to ensure that the widest pos- sible range of system can check the integrity of the release files. NetBSD/atari subdirectory structure The atari-specific portion of the NetBSD 3.0 release is found in the atari subdirectory of the distribution: .../NetBSD-3.0/atari/. It con- tains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-ATARITT.gz A kernel specifically tuned for the Atari TT030. netbsd-BOOT.gz A kernel for both the Falcon and TT030. It is kept pretty small, so you can use it to boot the system for installation on memory-tight systems. This is the kernel supplied on the boot.fs floppy. netbsd-BOOTX.gz Same as the BOOT kernel, but it has slightly more features. You can run X11 with it. netbsd-FALCON.gz A kernel specifically tuned for the Atari Falcon. netbsd-HADES.gz A kernel specifically tuned for the Hades. netbsd-MILAN-ISAIDE.gz A kernel specifically tuned for the MILAN using IDE in ISA mode. netbsd-MILAN-PCIIDE.gz A kernel specifically tuned for the MILAN using IDE in PCI mode. sets/ atari binary distribution sets; see below. installation/ floppy/ atari boot and installation floppies; see below. miniroot/ atari miniroot file system image; see below. misc/ Binary distribution sets The NetBSD atari binary distribution sets contain the binaries which com- prise the NetBSD 3.0 release for the atari. The binary distribution sets can be found in the atari/binary/sets subdirectory of the NetBSD 3.0 dis- tribution tree, and are as follows: base The NetBSD 3.0 atari base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally func- tional. It includes shared library support, and excludes every- thing described below. 16 MB gzipped, 46 MB uncompressed comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. 18 MB gzipped, 69 MB uncompressed etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. 1 MB gzipped, 1 MB uncompressed games This set includes the games and their manual pages. 3 MB gzipped, 7 MB uncompressed kern-BOOT, kern-HADES, kern-MILAN-ISAIDE, kern-MILAN-PCIIDE These sets contain a NetBSD/atari 3.0 kernel, named /netbsd. You must install the kernel that matches your hardware. 2 MB gzipped, 3 MB uncompressed man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. 8 MB gzipped, 30 MB uncompressed misc This set includes the (rather large) system dictionaries, the typesettable document set, and other files from /usr/share. 3 MB gzipped, 9 MB uncompressed text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. 2 MB gzipped, 7 MB uncompressed NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 4.4.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. 6 MB gzipped, 17 MB uncompressed xcomp The extra libraries and include files needed to compile X source code. 10 MB gzipped, 37 MB uncompressed xfont Fonts needed by X. 31 MB gzipped, 39 MB uncompressed xetc Configuration files for X which could be locally modified. 0.03 MB gzipped, 0.17 MB uncompressed xserver The X server. Please consult the X specific section in the atari FAQ as to which server you should use. 3 MB gzipped, 7 MB uncompressed The atari binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xpf command from the root directory ( / ) of your system. Additional kernels to those included in the distribution sets may be found in the atari/binary/kernel subdirectory of the NetBSD 3.0 distribu- tion tree. These kernels are generally named something like netbsd-BOOT.gz or some other suitable name. Please note that these ker- nels are simply gzipped and are not in tar archives. There are six atari floppy images to be found in the atari/installation/floppies subdirectory of the NetBSD 3.0 distribution. Three of them are bootable TOS kernel floppies and the other three are installation floppies. They are described in more detail below. There are gzipped versions of each available, for easier downloading. (The gzipped versions have the .gz extension added to their names.) Bootable Kernel floppies These TOS disks contains the TOS support programs (like loadbsd.ttp and chg_pid.ttp -- see below) and a kernel. They are setup such that you can insert them into your floppy drive, and start the programs from GEM. For the TT030 and Falcon, the (720 KB) floppy is named boot.fs and the kernel supplied is BOOT. For the Hades, you need the hades-boot.fs floppy (1.44 MB), the kernel is HADES. For the Milan, you need the milan-boot.fs floppy (1.44 MB), the kernel is MILAN-PCIIDE. Installation floppy: This disk contains a BSD root file system setup to help you install the rest of NetBSD. This includes formatting and mount- ing your / (root) and /usr partitions and getting ready to extract (and possibly first fetching) the distribution sets. There is enough on this file system to allow you to make a slip connection, configure an ethernet, mount an NFS file system or ftp. You can also load distribution sets from a SCSI tape or from one of your existing GEMDOS partitions. The floppies meant for 720 KB disks are named miniroot.fs.1 and miniroot.fs.2. There is also an image for an 1.44 MB disk: miniroot.fs. There are also TOS utilities in the atari/installation/misc subdirectory, which you will need to get NetBSD/atari up-and-running. o The gzip.ttp program allows you to uncompress .gz images. The usage is: gzip.ttp -d filename.gz o The rawwrite.ttp program allows you to create the installation floppy disks from the files in the atari/floppies directory. o The aptck.ttp program reads the partition tables present on a given disk and tries to interpret then the same way the NetBSD kernel does. If you have a disk on which GEMDOS and NetBSD are to co-exist, It is a good idea to run this before you begin the NetBSD/atari installa- tion just to check that the kernel's view of the partition tables agree with GEMDOS's view. If you have more than 3 partitions defined on a disk you will notice that the NetBSD/atari partition starts one sector after the GEMDOS partition. This is to allow space for the auxiliary root for the 4th and subsequent partitions. o The loadbsd.ttp program loads the NetBSD/atari kernel from TOS (or MiNT, MultiTOS, etc.). o The chg_pid.ttp program can be used to change the id of an AHDI com- patible partition. This allows you to reserve a partition for use by NetBSD/atari (id: NBD), or for use as a swap (id: SWP) partition. o The file2swp.ttp program can be used to transfer an installation file system image, like sysinst.fs to a partition with id SWP. In this way, you can run the installation from the swap partition instead of a memory disk. This is a necessity for small memory systems. This utility is used only in a Traditional method installation. Note: Each directory in the atari binary distribution also has its own checksum files, just as the source distribution does. NetBSD/atari System Requirements and Supported Devices NetBSD/atari 3.0 runs on a TT030, Falcon, Hades and MilanI. An FPU is not required. The minimum amount of RAM required is 4 MB. On the Hades, only the Tseng PCI VGA cards (ET4000/ET6000/ET6100) are supported in the 3.0 release. When an unsupported video card is present, you can use NetBSD with a serial console only. Here is a table of recommended HD partition sizes for a full install: Partition Suggested + X Needed + X root (/) 25 MB 25 MB 20 MB 20 MB /usr 245 MB 270 MB 120 MB 145 MB /var 20 MB 20 MB 5 MB 5 MB swap 2*RAM below 32 MB, then up to you Anything else is up to you! In addition of the rule of thumb for the swap size mentioned below, you probably want to make sure that the size of the swap partition does not drop below 20 MB (30 MB for systems with X). Another item is the add-on packages. You might want 20-30M (or more) in /usr/local (or added to /usr) to store packages from the NetBSD package system. As you may note the recommended size of /usr is 125 MB greater than needed. This is to leave room for a kernel source and compile tree as you will probably want to compile your own kernel. (GENERIC is large and bulky to accommodate all people, BOOT is small and might not have all the features you want). Supported devices o The builtin SCSI host adapter - Should support most SCSI-drives. - Should support most tape drives. - Should support most CD-ROM drives. - Should support most ZIP/M-O drives. o The builtin video controller o The builtin (720 KB / 1.44 MB) floppy drive o The serial2/modem2 ports o The Falcon FX memory expansion o The Atari mouse o A 3-button mouse (see build description in the FAQ!) o The parallel printer o IDE interface on both Falcon and Hades (includes ATAPI support) o The serial interface on the first 68901 UART (modem1) o VME-bus devices (TT030/Hades) - BVME410 ethernet - Circad Leonardo 24-bit VME graphics adapter - Crazy Dots VME et4000 graphics adapter - Riebl (and possibly PAM) ethernet cards on the VME bus. o PCI-bus devices (Hades and Milan only) - ET4000/ET6000/ET6100-PCI (VGA console) - ESS Technology Inc. Solo-1 Soundcard - 3Com 3c59x Network card o ISA-bus devices (Hades only) - Teles S0/16.3-ISA ISDN adapter (with I4B) This list is incomplete by definition. We can not test all SCSI periph- erals, ISA cards or PCI cards. If you have problems with such a periph- eral, please contact the port-atari@NetBSD.org mailing list. Getting the NetBSD System on to Useful Media Installation is supported from several media types, including: o GEMDOS/TOS HD partitions o Tape No matter what you do, however, you'll need to have three disks handy, on which you will put the install and boot floppy images. All the images are available from the directory installation/floppies under the root of the NetBSD/atari tree at your favorite archive site. If you are using NetBSD/atari to make the floppies, you should use the command dd(1) to write the raw floppy images (.fs files) to the disk. As an example, to write the first part of the miniroot file system onto a 720 KB floppy in fd0 use: # dd if=miniroot.fs.1 of=/dev/rfd0b bs=9b If you are using TOS to make the floppies, grab the rawwrite utility from the atari/utils directory and issue the command: rawwrite boot.fs This will create the boot-floppy on the floppy in drive a. The floppies should be pre-formatted on 720 KB / 1.44 MB for both the dd and rawwrite commands to work. Pre-formatting can be best done using the desktop for- mat command. Some other utilities seem to be giving problems. Since the 1.3 release, it is also possible to use HD-floppies. You should than use the floppy device /dev/rfd0c or add the -H flag to rawwrite. The steps necessary to prepare the distribution sets for installation depend on which method of installation you choose. The various methods are explained below. GEMDOS To install NetBSD from a GEMDOS partition, you need to get the NetBSD distribution sets you wish to install on your system on to a GEMDOS partition. Note where you placed the files, you will need this later. Once you have done this, you can proceed to the next step in the installation process, preparing your hard disk. Tape To install NetBSD from a tape, you need to somehow get the NetBSD filesets you wish to install on your system on to the appropriate kind of tape. If you make the tape on a UNIX -like system, you can create it as follows: # cd .../NetBSD-3.0/atari/binary/sets # T=tape_device # mt -f $T rewind # for f in base etc comp games man misc text dd if=$f.tgz of=$T conv=sync bs=5k # done # mt -f $T rewind where ``tape_device'' is the name of the (non-rewinding!) tape device that you're using (probably something like /dev/nrst0, but we make no guarantees 8-). If you can't figure it out, ask your system administrator. Once you have done this, you can proceed to the next step in the installation process, preparing your hard disk. Preparing your System for NetBSD installation Preparing your hard disk for the NetBSD installation. Note you will be modifying your HD's if you mess something up here you could lose everything on all the drives that you work with. It is there- fore advised that you: o Write down your current configurations. Do this by writing down all partition info (especially their sizes). o Back up the partitions you are keeping. If NetBSD has to share the disk with another operating system, you can either take care of partitioning your harddisk before installing NetBSD or delay this until the installer requests you to do it. If you decide to do it now, please create space for at least / (root), swap and /usr partitions and possibly at least one more for /local if you have the space. Whatever you decide, take note of the paragraphs below! You need this info to create bootable disks. Warning: The AHDI partioning function erases all partions on your hard- disk even if they are not changed! We know this is rather stupid, but don't say we didn't warn you. If you want to use an AHDI partitioning scheme and you want to be able to boot directly into NetBSD, there are some constraints on the partition layout. As you might know; every hard disk has a `root sector' that contains information about the size of the hard disk and the partitions on the hard disk. The root sector can only contain the necessary data for four partitions. Nobody thought that this limitation would cause any prob- lems. After all, 640 KByte should be enough. As hard disk grew, it was necessary to define more than four partitions. In order to be more or less compatible with the old format, a new type of partition entry was defined: XGM partions. An XGM partition is a `look over there' sign: Another root sector can be found at the start of the XGM partition. This root sector contains the remaining real partitions. And this is the big mystery: Partitions defined in the root sector of the hard disk are called `primary partitions', partitions defined in the root sector of an XGM partition are called `extended partitions'. The bootblock will only work if the first NBD partition is a primary par- tition. This is not a limitation of NetBSD but a limitation of TOS/AHDI: You can only boot from primary partitions. If you are creating your partitions with HDX, you'll have to be very careful to fulfill this rule. HDX has some very strange ideas when it comes to extended partitions. Fortunately, you can edit this stuff: The ``Edit partition scheme of the unit'' dialog box has a button labeled ``expert''. This button is inactive unless you have defined more than four partitions. Click on it after you have defined the sizes of the partitions. A new dialog box appears on the screen. The left side contains two blocks of partitions; the upper block always contains the first four par- titions, the lower block contains the last three partitions. If you have defined less than 7 partitions, some fields of the lower block will con- tain the string ``unused''. Some of the partitions will be displayed in reverse video: These are the extended partitions. The right side contains six possible ranges for the extended partitions. It is not possible to define your own range, you will have to use one of the schemes offered by HDX. To quote from Ghostbusters: Choose and die. The default scheme used by HDX is the first scheme: Extended partitions start with the second partition and end with the second to last parti- tion. If you have defined 7 partitions, partitions #2 to #5 will be extended partitions, while partitions #1, #6 and #7 will be primary par- titions. You can move the extended partition range by clicking on one of the but- tons on the right side of the dialog box. Try to find one where your first NetBSD partition is a primary partition. Golden rules: o If the disk contains no GEMDOS partitions, don't use AHDI. Let NetBSD handle it alone. o If the disk contains one GEMDOS partition, make it partition #1 and start the extended partition range at partition #3. This allows you to boot from both the GEMDOS and the NetBSD partitions. o If the disk contains two GEMDOS partitions, use partitions #1 and #2 for GEMDOS, partition #3 for NetBSD-root. Start the extended parti- tion range with partition #4. o If your disks contains three or more GEMDOS partitions, you are in trouble. Try using partitions #1 and #2 as the first two GEMDOS par- titions. Use partition #3 as the first NetBSD partition. Start the extended partition range with partition #4. Put the other NetBSD extended partition range. Booting the installer on an existing system If you already have NetBSD installed, it is easy. Just boot into single user state on your current system, or use the shutdown now command to shutdown to single-user state. Then copy the installer using dd: dd if=sysinst.fs of=/dev/rsd0b where /dev/rsd0b should be the device path of the swap partition your system is configured to use. Once the file is copied, reboot back to the booter and use the '-b' option to make the kernel prompt for a root device. Now enter the swap device as your root device to start the installer. Booting the installer on new systems. If your system has more than 6MB RAM, you can skip directly to the sec- tion about loadbsd.ttp, since the amount of RAM is enough to load the installer into. For new new installations on small memory systems, things are a bit more complicated. The easiest way is to mark an AHDI partition as id 'SWP'. You can either accomplish this with HDdriver or use the chg_pid.ttp pro- gram supplied on the bootfloppy. To use the fifth partition of your first drive to a swap partition, do the following: chg_pid -w 0 4 SWP As you can see, both the drive and the partition numbers are zero based. When a swap partition has been created, you can transfer the installer using the file2swp.ttp command, which is also on the bootfloppy. This program copies a (gzipped)file to the first AHDI partition with id 'SWP' on the designated disk. To copy sysinst.fs to your first SCSI disk, use: file2swp -w -f sysinst.fs s0 Note that file2swp automatically detects a gzipped file, there is no need for a .gz extension. Using loadbsd.ttp To start the installer, you first need to load a NetBSD kernel. This can be done in a couple ways, both of which currently require GEMDOS. You need either the bootfloppy provided in the distribution or you can copy the loadbsd.ttp program and kernel to a boot floppy disk (1.44 MB needed) or put them on a TOS partition. Select the loadbsd program and it will ask for parameters, supply: `-b netbsd' (or whatever name you copied the kernel to). You can, of course, also run it from the shell command-line in MiNT: loadbsd -b a:/netbsd You should see the screen clear and some information about your system as the kernel configures the hardware. Then you will be prompted for a root device. If you copied the installer to a swap partition, as explained above, you have to enter the swap partition as the boot device. When you used your first SCSI disk, this will be sd0b. On the first IDE drive it would be wd0b. When you didn't copy the installer to swap, need to use the RAMdisk, so remove the GEMDOS kernel boot floppy from the drive if present and insert the NetBSD install floppy 1. Now enter the name of the boot device depending on the floppy type you have inserted. Use: o md0a for the old installer (1MB filesystem) on 720KB floppy's. o md1a for the sysinst installer on 720KB floppy's. o md2a for the sysinst installer on 1.44MB floppy's. The kernel will load the install file system into RAMdisk. While the kernel is loading, it will show a `.' for each track loaded. After load- ing 80 tracks, it will ask you to insert the next floppy. At this time, insert the NetBSD install floppy 2 and press any key. The kernel contin- ues loading another 40 tracks before it continues to boot. Installing the NetBSD System Installing NetBSD is a relatively complex process, but, if you have this document in hand and are careful to read and remember the information which is presented to you by the install program, it shouldn't be too much trouble. Before you begin, you must have already prepared your hard disk as detailed in the section on preparing your system for install. The following is a walk-through of the steps necessary to get NetBSD installed on your hard disk. Running the sysinst installation program 1. Introduction Using sysinst, installing NetBSD is a relatively easy process. You still should read this document and have it in hand when doing the installation process. This document tries to be a good guideline for the installation and as such covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. General The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installation system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst pro- gram from the command prompt. It is not necessary to reboot. 3. Quick install First, let's describe a quick install. The other sections of this document go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instruc- tions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. o What you need. - The distribution sets (in this example, they are on CD). - A floppy disk containing a suitable boot.fs and a floppy with the sysinst.fs image. See the "prepare" section about obtaining those. - A CD-ROM drive (SCSI or ATAPI), a hard disk and a minimum of 4 MB (TT030/Falcon) or 16 MB (Hades/Milan) of memory installed. - The hard disk should have at least 120 + n megabytes of space free, where n is the number of megabytes of main mem- ory in your system. If you wish to install the X Window System as well, you will need at least 120 MB more. o The Quick Installation - Boot the system as described above. You should be at the sysinst main menu. .***********************************************. * NetBSD-3.0 Install System * * * *a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * x: Exit Install System * .***********************************************. - If you wish, you can configure some network settings immedi- ately by choosing the Utility menu and then Configure network. It isn't actually required at this point, but it may be more convenient. Go back to the main menu. - Choose install. - You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. WARNING: If you want your disk to retain an AHDI compatible partitioning, make sure to use the 'exist- ing' disk layout. - After your disk has been prepared, choose CD-ROM as the medium. The default values for the path and device should be ok. - After all the files have been unpacked, go back to the main menu and select reboot, after you have removed the boot- floppy from the drive. - NetBSD will now boot. If you haven't already done so in sysinst, you should log in as root, and set a password for that account. You are also advised to edit the file /etc/rc.conf to match your system needs. - Your installation is now complete. - For configuring the X window system, if installed, see the files in /usr/X11R6/lib/X11/doc. Further information can be found on http://www.xfree86.org/. 4. Booting NetBSD Boot the system as described in the "Booting the installer" section above. It will take a while to load the kernel from the floppy, probably around a minute or so, then, the kernel boot messages will be dis- played. This may take a little while also, as NetBSD will be prob- ing your system to discover which hardware devices are installed. You may want to read the boot messages, to notice your disk's name and geometry. Its name will be something like sd0 or wd0 and the geometry will be printed on a line that begins with its name. As mentioned above, you may need your disk's geometry when creating NetBSD 's partitions. You will also need to know the name, to tell sysinst on which disk to install. The most important thing to know is that wd0 is NetBSD 's name for your first IDE disk, wd1 the sec- ond, etc. sd0 is your first SCSI disk, sd1 the second, etc. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 5. Network configuration If you will not use network operation during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu, and select the Configure network option. If you only want to temporarily use net- working during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response in reply to answers relating to this. 6. Installation drive selection and parameters To start the installation, select Install NetBSD to hard disk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. Depending on how many disks are found, you may get a different message. You should see disk names like sd0 or sd1. 7. Partitioning the disk o Preparing a disk which will be used for GEM and NetBSD. You will be prompted if you want an AHDI compatible partitioning on your disk. If you are installing NetBSD on a dedicated drive, just answer 'no' and skip to the next section. If you answer 'yes', the ahdilabel program is started. You can now change the AHDI partition ID's on your root disk. Because NetBSD imposes a special ordering in disk partitions it uses for / (root) and swap. Also, because it wants to guard you against an unwanted demolition of partitions used by other systems, you have to tell it what partitions it is allowed to use. You have to mark the partition you want to use as swap SWP or (depre- cated!) NBS and the other partitions as NBD. Note that all the changes you make to the ID's are reversible as long as you remember the original value. ahdilabel is capable of creating or changing an AHDI compatible partitioning on the disk, and in the partition-ID editor, the partitions are shown in the order that AHDI created them. When you leave this editor and continue with sysinst, your changes to the ID's do have consequences to the partition order! They will show up as follows: a the first NBD partition b the first SWP (or NBS) partition d (and up) the rest of the partitions in AHDI order 8. Editing the NetBSD disklabel The partition table of the NetBSD part of a disk is called a disklabel. There are 4 layouts for the NetBSD part of the disk that you can pick from: Standard, Standard with X, Custom and Use Existing. The first two use a set of default values (that you can change) suitable for a normal installation, possibly including X. With the Custom option you can specify everything yourself. The last option uses the partition info already present on the disk. If you want to use NetBSD on an AHDI partitioned disk, you will have to use: Use Existing. You will be presented with the current layout of the NetBSD diskla- bel, and given a chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap partition has a special type called swap. Some partitions in the disklabel have a fixed purpose. a Root partition (/) b Swap partition. c The NetBSD portion of the disk. d-p Available for other use. Traditionally, d is the par- tition mounted on /usr, but this is historical prac- tice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it something different, make sure the name is a single word and con- tains no special characters. You don't need to remember this name. 9. Preparing your hard disk You are now at the point of no return. Apart from the changes you made with ahdilabel nothing has been modified on your disk yet. If you confirm that you want to install NetBSD, the partitions now assigned to NetBSD will be actually written to. If you are sure you want to proceed, enter yes at the prompt. The install program will now label your disk and make the file sys- tems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are running. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Otherwise, you can continue the installa- tion program after pressing the return key. 10. Getting the distribution sets The NetBSD distribution consists of a number of sets, that come in the form of gzipped tarfiles. A few sets must be installed for a working system, others are optional. At this point of the installa- tion, you will be presented with a menu which enables you to choose from one of the following methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 11. Installation using ftp To be able to install using ftp, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these ques- tions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the ftp server. sysinst will proceed to transfer all the default set files from the remote site to your hard disk. 12. Installation using NFS To be able to install using NFS, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these ques- tions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e. correctly exported to your machine. If you did not set up DNS when answering the questions to configure networking, you will need to specify an IP address instead of a hostname for the NFS server. 13. Installation from CD-ROM When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM player (usually cd0), and the directory name on the CD-ROM where the distribution files are. sysinst will then check if the files are indeed available in the specified location, and proceed to the actual extraction of the sets. 14. Installation from an unmounted file system In order to install from a local file system, you will need to spec- ify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location. 15. Installation from a local directory This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file sys- tem that is already accessible. sysinst will ask you for the name of this directory. 16. Extracting the distribution sets After the install sets containing the NetBSD distribution have been made available, you can either extract all the sets (a full instal- lation), or only extract sets that you have selected. In the latter case, you will be shown the currently selected sets, and given the opportunity to select the sets you want. Some sets always need to be installed (kern, base) and etc they will not be shown in this selection menu. Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably, especially on machines with slow graphics consoles or serial consoles. After all the files have been extracted, all the necessary device node files will be created. If you have already configured network- ing, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the net- work configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can than set a password for the "root" account, to prevent the machine coming up without access restric- tions. 17. Finalizing your installation Congratulations, you have successfully installed NetBSD 3.0. You can now reboot the machine, and boot NetBSD from hard disk. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state, with the most important ones described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the sys- tem asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi- user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). If your /usr directory is on a separate partition and you do not know how to use ed, you will have to mount your /usr partition to gain access to ex or vi. Do the following: # mount /usr # export TERM=vt220 If you have /var on a separate partition, you need to repeat that step for it. After that, you can edit /etc/rc.conf with vi(1). When you have finished, type exit at the prompt to leave the single- user shell and continue with the multi-user boot. Other values that need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute, furthermore add an ifconfig_int for your network interface, along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Select the proper terminal devices You will have to edit the /etc/ttys file. If you don't have a Milan, you must disable the ttyEx devices. For the Milan, you will have to disable the ttyex devices. This is easy, just change 'on' to 'off' on the corresponding lines. 3. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. If you're using the machine in a networked environment, you should cre- ate an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. Unless you have connected an unusual terminal device as the console you can just press RETURN when it prompts for Terminal type? [...]. 4. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 5. The X Window System If you have installed the X Window System, look at the files in /usr/X11R6/lib/X11/doc for information. Don't forget to add /usr/X11R6/bin to your path in your shell's dot file so that you have access to the X binaries. 6. Installing third party packages If you wish to install any of the software freely available for UNIX -like systems you are strongly advised to first check the NetBSD package system. This automatically handles any changes necessary to make the software run on NetBSD, retrieval and installation of any other packages on which the software may depend, and simplifies installation (and deinstallation), both from source and precompiled binaries. o More information on the package system is at http://www.NetBSD.org/Documentation/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc/README.html o Precompiled binaries can be found at ,: ftp://ftp.NetBSD.org/pub/NetBSD/packages/ usually in the 3.0/atari/All subdir. You can install them with the following commands under sh(1): # PKG_PATH=ftp://ftp.NetBSD.org/pub/NetBSD/packages/3.0/atari/All # export PKG_PATH # pkg_add -v tcsh # pkg_add -v bash # pkg_add -v perl # pkg_add -v apache # pkg_add -v kde # pkg_add -v mozilla ... If you are using csh(1) then replace the first two lines with the following: # setenv PKG_PATH ftp://ftp.NetBSD.org/pub/NetBSD/packages/3.0/atari/All ... The above commands will install the Tenex-csh and Bourne Again shell, the Perl programming language, Apache web server, KDE desktop environment and the Mozilla web browser as well as all the packages they depend on. o Package sources for compiling packages on your own can be obtained by retrieving the file ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-current/tar_files/pkgsrc.tar.gz They are typically extracted into /usr/pkgsrc (though other locations work fine), with the commands: # mkdir /usr/pkgsrc # ( cd /usr/pkgsrc ; tar -zxpf - ) pkgsrc.tar.gz After extracting, see the README and doc/pkgsrc.txt files in the extraction directory (e.g. /usr/pkgsrc/README) for more infor- mation. 7. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/mail/sendmail.cf file will almost definitely need to be adjusted; files aiding in this can be found in /usr/share/sendmail. See the README file there for more infor- mation. If you prefer postfix as MTA, adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the man- ual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System The upgrade to NetBSD 3.0 is a binary upgrade; it can be quite difficult to update the system from an earlier version by recompiling from source, primarily due to interdependencies in the various components. To do the upgrade, you must first boot the system as described in the Booting the installer section. You must also have at least the base and kern binary distribution sets available, so that you can upgrade with them, using one of the upgrade methods described above. Finally, you must have sufficient disk space available to install the new binaries. Since files already installed on the system are overwritten in place, you only need additional free space for files which weren't previously installed or to account for growth of the sets between releases. If you have a few megabytes free on each of your root (/) and /usr partitions, you should have enough space. Since upgrading involves replacing the kernel, the boot blocks on your NetBSD partition, and most of the system binaries, it has the potential to cause data loss. You are strongly advised to back up any important data on the NetBSD partition or on another operating system's partition on your disk before beginning the upgrade process. The upgrade procedure using the sysinst tool is similar to an installa- tion, but without the hard disk partitioning. sysinst will attempt to merge the settings stored in your /etc directory with the new version of NetBSD. Getting the binary sets is done in the same manner as the installation procedure; refer to the installation part of the document for how to do this. Also, some sanity checks are done, i.e. file sys- tems are checked before unpacking the sets. After a new kernel has been copied to your hard disk, your machine is a complete NetBSD 3.0 system. However, that doesn't mean that you're fin- ished with the upgrade process. You will probably want to update the set of device nodes you have in /dev. If you've changed the contents of /dev by hand, you will need to be careful about this, but if not, you can just cd into /dev, and run the command: # sh MAKEDEV all Finally, you will want to delete old binaries that were part of the ver- sion of NetBSD that you upgraded from and have since been removed from the NetBSD distribution. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 3.0. Issues affecting an upgrade from NetBSD 2.1 and older releases. It is very important that you populate the directory /etc/pam.d with appropriate configuration files for the Pluggable Authentication Modules (PAM) because you will not be able to login any more otherwise. Using postinstall as described below will take care of this. Please refer to http://www.netbsd.org/guide/en/chap-pam.html for documentation about PAM. The following issues can generally be resolved by extracting the etc set into a temporary directory and running postinstall: postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/pam.d/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* The following issues need to be resolved manually: - The user `_pflogd' and the groups `_pflogd' and `authpf' need to be created. Using online NetBSD documentation Documentation is available if you first install the manual dis- tribution set. Traditionally, the ``man pages'' (documenta- tion) are denoted by `name(section)'. Some examples of this are - intro(1), - man(1), - apropros(1), - passwd(1), and - passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative informa- tion is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the section should not be entered, but rather indi- cate that the section is optional. If you don't ask for a par- ticular section, the topic with the lowest numbered section name will be displayed. For instance, after logging in, enter # man passwd to read the documentation for passwd(1). To view the documen- tation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter apropos subject-word where subject-word is your topic of interest; a list of possi- bly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mail- ing list server, send mail to that address with an empty body, and it will reply with instructions. There are various mailing lists set up to deal with comments and questions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: netbsd-bugs@NetBSD.org. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/MailingLists/. If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-help@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to - The former members of UCB's Computer Systems Research Group, including (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encour- agement. - The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. - The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. - The Helsinki University of Technology in Finland for host- ing the NetBSD backup CVS and backup server. - SSH Communications Security in Finland for operating the backup server. - The many organizations that provide NetBSD mirror sites. - Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the vari- ous other people who've had a hand in making CVS a useful tool. - The following individuals and organizations (each in alpha- betical order) have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it: AMD - Advanced Micro Devices, Inc. ASA Computers Aaron Wall ABE Masayuki AboveNet Communications, Inc. Achim Grolms Adam Kasper Adaptec Advanced System Products, Inc. Akihiro IIJIMA Alex Poylisher Algorithmics, Ltd. Alistair Crooks Allegro Networks Aloys Keller Andreas Berg Andreas Jellinghaus Andrew Brown Andrew Gillham Andy Hagans Antonio Larripa Arend Harrewijne Armijn Hemel Atsushi YOKOYAMA Avalon Computer Systems Bay Area Internet Solutions Ben Collver Benoit Lepage Bernhard Moellemann Bill Coldwell Bill Sommerfeld Bill Squier Brad Salai Brains Corporation, Japan Brian Carlstrom Brian McGroarty Brian Mitchell Canada Connect Corporation Carl Shapiro Castor Fu Central Iowa (Model) Railroad Charles Conn Charles D. Cranor Charles M. Hannum Chris Legrow Chris Townsend Christer O. Andersson Christopher G. Demetriou Christos Zoulas Chuck Silvers Cologne Chip AG Computer und Literatur Verlag Computertechnik Krienke & Nolte Computing Services Department, The University of Liverpool Convert Tools Co-operative Research Centre for Enterprise Distributed Curt Sampson DAYOMON from Japan Damicon Kraa, Finland Daniel de Kok Dave Burgess Dave Rand Dave Tyson David Brownlee Dayton Clark Demon Internet, UK Derek Fellion Digital Equipment Corporation Distributed Processing Technology Distro Jockey Douglas J. Trainor Dr.ir. F.W. Dillema Easynet, UK Ed Braaten Edward Richley emuty Eric and Rosemary Spahr Erik Berls Erik E. Fair Erkki Ruohtula Ernst Lehmann Espen Randen Ewald Kicker Florent Parent Frank Kardel Free Hardware Foundation Front Range *BSD User Group FUKAUMI Naoki Gan Uesli Starling Garth R. Patil Geert Hendrickx (ghen) Geert Jan de Groot GK Meier Gordon Zaft Grant Beattie Greg Gingerich Greg Girczyc Guenther Grau HP Sweden Hanno Wagner Hans Huebner Harald Koerfgen Haroon Khalid Harry McDonald Hauke Fath Heiko W. Rupp Herb Peyerl Hernani Marques Madeira Hidekichi Ookubo Hideyuki Kido Hisashi Fujinaka Holger Weiss Hubert Feyrer IBM Corporation IMAI Kiyoshi Innovation Development Enterprises of America Intel Internet Software Consortium Internet Users Forever IKI Interoute Telecommunications, UK JNUG (raised at JNUG meeting & BOF August 2005) James Bursa James Chacon Jan Joris Vereijken Jason Birnschein Jason Brazile Jason R. Thorpe Jeff Rizzo Jeff Woodall - Portland, OR Jens Schoenfeld Jim Wise Joachim Nink Joachim Thiemann Joel CARNAT John Heasley John Kohl John P. Refling Jonathan P. Kay Jordan K. Hubbard Jorgen Lundman Karl Wagner Kenji Hisazumi Kenneth Alan Hornstein Kenneth P. Stox Kevin Keith Woo Kevin Sullivan Klaus Lichti Kimmo Suominen Korea BSD User Forum Krister Waldfridsson Kwok Ng Lars Mathiassen Lehmanns Fachbochhandlung Lex Wennmacher LinuxFest Northwest Luke Maurits Luke Mewburn MS Macro System GmbH, Germany Maki Kato Marc Tooley Marcus Wyremblewski Mark Brinicombe Mark Houde Mark Perkins Mark S. Thomas Mason Loring Bliss Martin Cernohorsky Martin J. Ekendahl Matt Dainty Matt Thomas Matthew Jacob Matthew Sporleder Matthias Scheler Mattias Karlsson Mel Kravitz Michael Graff Michael "Kvedulv" Moll Michael L. Hitch Michael Richardson Michael Thompson Michael W. James Mike Price Mirko Thiesen (Thiesi) Murphy Software BV, Netherlands Neil J. McRae Noah M. Keiserman Norman R. McBride Numerical Aerospace Simulation Facility, NASA Ames Research Olaf "Rhialto" Seibert Oliver Cahagne Oppedahl & Larson LLP Palle Lyckegaard Paul Ripke Paul Southworth Pawel Rogocz Pearson Education Perry E. Metzger Petar Bogdanovic Peter C. Wallace Peter J. Bui Peter Postma Petri T. Koistinen Phil Thomas Piermont Information Systems Inc. Pierre-Philipp Braun Precedence Technologies Ltd Public Access Networks Corporation Ralph Campbell Randy Ray Real Weasel Reinoud Zandijk Renewed Health Company Richard Nelson Rob Windsor Robert Pankratz Robert Thille Roland Lichti Ross Harvey Ryan Campbell SDF Public Access Unix, Inc. 501(c)(7) SMC Networks Inc. Salient Systems Inc. Sander van Dijk Scott Ellis Scott Kaplan Scott Walters Sean Davis Simon Burge Soren Jacobsen Soren Jorvang Stephen Borrill Stephen Early Steve Allen Steve Wadlow Steven M. Bellovin SunROOT# Project Sylvain Schmitz Takahiro Kambe TAKEUCHI Yoji Tamotsu Kanoh Tasis Michalakopoulos (Athens, Greece) Tatoku Ogaito Ted Lemon Ted Spradley The Names Database The NetBSD Mission The People's Republic of Ames Thierry Lacoste Thierry Laronde Thomas Runge Thor Lancelot Simon Tim Law Timo Scholer Tino Hanich Tino Wildenhain Tom Coulter Tom Ivar Helbekkmo Tom Lyon Tomas Dabasinskas Torsten Harenberg Toru Nishimura Toshiba Turbocat's Development Tyler Sarna UTN Web Directory VMC Harald Frank, Germany Warped Communications, Inc. Wasabi Systems, Inc. Whitecross Database Systems Ltd. William Gnadt Worria Affordable Web Hosting Worria Web Hosting wwwTrace Traceroute Server Directory Yusuke Yokota Zach Metzinger (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) - Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in Jan- uary, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Allen Briggs briggs@NetBSD.org Matt Thomas matt@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): ~ Allen Briggs briggs@NetBSD.org sandpoint Anders Magnusson ragge@NetBSD.org vax Andrey Petrov petrov@NetBSD.org sparc64 Ben Harris bjh21@NetBSD.org acorn26 Chris Gilbert chris@NetBSD.org cats Christian Limpach cl@NetBSD.org xen Eduardo Horvath eeh@NetBSD.org evbppc Frank van der Linden fvdl@NetBSD.org amd64 Frank van der Linden fvdl@NetBSD.org i386 Gavan Fantom gavan@NetBSD.org iyonix IWAMOTO Toshihiro toshii@NetBSD.org hpcarm Ichiro Fukuhara ichiro@NetBSD.org hpcarm Ignatios Souvatzis is@NetBSD.org amiga Izumi Tsutsui tsutsui@NetBSD.org hp300 Izumi Tsutsui tsutsui@NetBSD.org news68k Jason Thorpe thorpej@NetBSD.org algor Jason Thorpe thorpej@NetBSD.org evbarm Jason Thorpe thorpej@NetBSD.org shark Jeremy Cooper jeremy@NetBSD.org sun3 Jonathan Stone jonathan@NetBSD.org pmax Julian Coleman jdc@NetBSD.org atari Jun-ichiro itojun Hagino itojun@NetBSD.org evbsh3 Jun-ichiro itojun Hagino itojun@NetBSD.org mmeye Kazuki Sakamoto sakamoto@NetBSD.org bebox Lennart Augustsson augustss@NetBSD.org pmppc Marcus Comstedt marcus@NetBSD.org dreamcast Martin Husemann martin@NetBSD.org sparc64 Matt DeBergalis deberg@NetBSD.org next68k Matt Fredette fredette@NetBSD.org hp700 Matt Fredette fredette@NetBSD.org sun2 Matt Thomas matt@NetBSD.org alpha Matt Thomas matt@NetBSD.org netwinder Matthias Drochner drochner@NetBSD.org cesfic NISHIMURA Takeshi nsmrtks@NetBSD.org x68k NONAKA Kimihiro nonaka@NetBSD.org prep Nathan Williams nathanw@NetBSD.org sun3 Noriyuki Soda soda@NetBSD.org arc Paul Kranenburg pk@NetBSD.org sparc Phil Nelson phil@NetBSD.org pc532 Reinoud Zandijk reinoud@NetBSD.org acorn32 Ross Harvey ross@NetBSD.org alpha Soren Jorvang soren@NetBSD.org cobalt Soren Jorvang soren@NetBSD.org sgimips Scott Reynolds scottr@NetBSD.org mac68k Shin Takemura takemura@NetBSD.org hpcmips Simon Burge simonb@NetBSD.org evbmips Simon Burge simonb@NetBSD.org evbppc Simon Burge simonb@NetBSD.org pmax Simon Burge simonb@NetBSD.org sbmips Steve Woodford scw@NetBSD.org evbsh5 Steve Woodford scw@NetBSD.org mvme68k Steve Woodford scw@NetBSD.org mvmeppc Tohru Nishimura nisimura@NetBSD.org luna68k Tsubai Masanari tsubai@NetBSD.org macppc Tsubai Masanari tsubai@NetBSD.org newsmips UCHIYAMA Yasushi uch@NetBSD.org hpcsh UCHIYAMA Yasushi uch@NetBSD.org playstation2 Wayne Knowles wdk@NetBSD.org mipsco Wolfgang Solfrank ws@NetBSD.org ofppc The NetBSD 3.0 Release Engineering team: Grant Beattie grant@NetBSD.org Erik Berls cyber@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Havard Eidnes he@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org Soren Jacobsen snj@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Luke Mewburn lukem@NetBSD.org Jeff Rizzo riz@NetBSD.org Matthias Scheler tron@NetBSD.org Curt Sampson cjs@NetBSD.org Jim Wise jwise@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Christoph Badura bad@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Grant Beattie grant@NetBSD.org Jason Beegan jtb@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Mason Loring Bliss mason@NetBSD.org Charles Blundell cb@NetBSD.org Rafal Boni rafal@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org John Brezak brezak@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Frederick Bruckman fredb@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Dave Carrel carrel@NetBSD.org Daniel Carosone dan@NetBSD.org James Chacon jmc@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Ben Collver ben@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Aidan Cully aidan@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Jed Davis jld@NetBSD.org Matt DeBergalis deberg@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Elad Efrat elad@NetBSD.org Havard Eidnes he@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Adam Glass glass@NetBSD.org Michael Graff explorer@NetBSD.org Brian C. Grayson bgrayson@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Ben Harris bjh21@NetBSD.org Ross Harvey ross@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org HAYAKAWA Koichi haya@NetBSD.org John Heasley heas@NetBSD.org Geert Hendrickx ghen@NetBSD.org Rene Hexel rh@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Christian E. Hopps chopps@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hornquist Astrand lha@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Chris Jones cjones@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Antti Kantee pooka@NetBSD.org Masanori Kanaoka kanaoka@NetBSD.org Frank Kardel kardel@NetBSD.org Mattias Karlsson keihan@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Mario Kemper magick@NetBSD.org Min Sik Kim minskim@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org John Kohl jtk@NetBSD.org Daniel de Kok daniel@NetBSD.org Paul Kranenburg pk@NetBSD.org Martti Kuparinen martti@NetBSD.org Kentaro A. Kurahone kurahone@NetBSD.org Kevin Lahey kml@NetBSD.org Johnny C. Lam jlam@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org Paul Mackerras paulus@NetBSD.org Anders Magnusson ragge@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org David Maxwell david@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Perry Metzger perry@NetBSD.org Simas Mockevicius symka@NetBSD.org Juan Romero Pardines xtraeme@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Minoura Makoto minoura@NetBSD.org Luke Mewburn lukem@NetBSD.org der Mouse mouse@NetBSD.org Joseph Myers jsm@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Phil Nelson phil@NetBSD.org John Nemeth jnemeth@NetBSD.org Bob Nestor rnestor@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Jonathan Perkin sketch@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Rui Paulo rpaulo@NetBSD.org Peter Postma peter@NetBSD.org Dante Profeta dante@NetBSD.org Chris Provenzano proven@NetBSD.org Niels Provos provos@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Michael Richardson mcr@NetBSD.org Tim Rightnour garbled@NetBSD.org Jeff Rizzo riz@NetBSD.org Gordon Ross gwr@NetBSD.org Steve Rumble rumble@NetBSD.org Ilpo Ruotsalainen lonewolf@NetBSD.org Heiko W. Rupp hwr@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Takeshi Shibagaki shiba@NetBSD.org Naoto Shimazaki igy@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org SOMEYA Yoshihiko someya@NetBSD.org Bill Sommerfeld sommerfeld@NetBSD.org Jorg Sonnenberger joerg@NetBSD.org Ignatios Souvatzis is@NetBSD.org Bill Squier groo@NetBSD.org Jonathan Stone jonathan@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org SUNAGAWA Keiki kei@NetBSD.org Kimmo Suominen kim@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Ian Lance Taylor ian@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Todd Whitesel toddpw@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Dan Winship danw@NetBSD.org Jim Wise jwise@NetBSD.org Michael Wolfson mbw@NetBSD.org Steve Woodford scw@NetBSD.org Colin Wood ender@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Maria Zevenhoven maria7@NetBSD.org Christos Zoulas christos@NetBSD.org Other contributors: Dave Burgess burgess@cynjut.infonet.net Brian R. Gaeke brg@dgate.org Brad Grantham grantham@tenon.com Lawrence Kesteloot kesteloo@cs.unc.edu Waldi Ravens waldi@moacs.indiv.nl.net Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trademarks of their respective owners. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Founda- tion. This product includes software developed by The NetBSD Founda- tion, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product contains software developed by Ignatios Souvatzis for the NetBSD project. This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project. This product contains software written by Michael L. Hitch for the NetBSD project. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) This product includes cryptographic software written by Eric Young (eay@mincom.oz.au) This product includes software designed by William Allen Simp- son. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Division, US Naval Research Laboratory. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Gordon W. Ross and Leo Weppelman. This product includes software developed by Hellmuth Michaelis and Joerg Wunsch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard University. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Alistair G. Crooks. This product includes software developed by Alistair G. Crooks. for the NetBSD project. This product includes software developed by Allen Briggs This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brad Pepers This product includes software developed by Bradley A. Grantham. This product includes software developed by Brini. This product includes software developed by Causality Limited. This product includes software developed by Charles D. Cranor and Seth Widoff. This product includes software developed by Charles D. Cranor and Washington University. This product includes software developed by Charles D. Cranor, Washington University, and the University of California, Berke- ley and its contributors. This product includes software developed by Charles D. Cranor, Washington University, the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the Univer- sity of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christian Limpach This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Cybernet Corpora- tion and Nan Yang Computer Services Limited This product includes software developed by Daishi Kato This product includes software developed by Dale Rahn. This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Darrin B. Jewell This product includes software developed by David Miller. This product includes software developed by Dean Huxley. This product includes software developed by Eduardo Horvath. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@mincom.oz.au) This product includes software developed by Eric Young (eay@cryptsoft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by Ezra Story and by Kari Mettinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Frank van der Lin- den for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Gordon W. Ross This product includes software developed by HAYAKAWA Koichi. This product includes software developed by Harvard University and its contributors. This product includes software developed by Harvard University. This product includes software developed by Herb Peyerl. This product includes software developed by Hubert Feyrer for the NetBSD Project. This product includes software developed by Iain Hibbert This product includes software developed by Ian F. Darwin and others. This product includes software developed by Ian W. Dall. This product includes software developed by Ichiro FUKUHARA. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jared D. McNeill. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Communications, http://www.and.com/ This product includes software developed by Joachim Koenig- Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Jukka Marin. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berkeley and its contributors. This product includes software developed by LAN Media Corpora- tion and its contributors. This product includes software developed by Leo Weppelman for the NetBSD Project. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Luke Mewburn. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Manuel Bouyer. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Murray This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Solfrank. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Mats O Jansson and Charles D. Cranor. This product includes software developed by Mats O Jansson. This product includes software developed by Matt DeBergalis This product includes software developed by Matthew Fredette. This product includes software developed by Matthias Pfaller. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Michael Graff. This product includes software developed by Michael L. Hitch. This product includes software developed by Michael Shalayeff. This product includes software developed by Michael Smith. This product includes software developed by Mike Glover and contributors. This product includes software developed by Mike Pritchard. This product includes software developed by Minoura Makoto. This product includes software developed by Nan Yang Computer Services Limited. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Onno van der Lin- den. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by Philip L. Budne. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Roland C. Dowdeswell. This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Soren S. Jorvang. This product includes software developed by Stephan Thesing. This product includes software developed by Steve Woodford. This product includes software developed by Takashi Hamada This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lam- bert. This product includes software developed by Tetsuya Isaki. This product includes software developed by Thomas Gerner This product includes software developed by Thomas Klausner for the NetBSD Project. This product includes software developed by Tobias Weingartner. This product includes software developed by Todd C. Miller. This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project. This product includes software developed by Tohru Nishimura for the NetBSD Project. This product includes software developed by Tohru Nishimura. for the NetBSD Project. This product includes software developed by TooLs GmbH. This product includes software developed by Toru Nishimura. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contributors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Science at the University of Utah. This product includes software developed by the Charles D. Cra- nor, Washington University, University of California, Berkeley and its contributors. This product includes software developed by the Computer Sys- tems Engineering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard Univer- sity and its contributors. This product includes software developed by the Kungliga Tekniska Hogskolan and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) his product includes software developed by the PocketBSD project and its contributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Development Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia University. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Christos Zoulas This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Ignatios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Michael L. Hitch. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden This product includes software developed for the NetBSD Project by Allegro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Piermont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Sys- tems Laboratory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Thomas Gerner This product includes software developed by Waldi Ravens. The End NetBSD August 22, 2004 NetBSD