INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL -- Installation procedure for NetBSD/evbppc. CONTENTS About this Document............................................2 What is NetBSD?................................................3 Changes Between The NetBSD 4.0 release and 4.0.1 update........3 Security Advisories Fixes...................................3 Other Security Fixes........................................4 Networking..................................................4 Libraries...................................................4 Drivers.....................................................4 Miscellaneous...............................................4 Platforms specific..........................................5 Changes Between The NetBSD 3.0 and 4.0 Releases................5 Networking..................................................5 File systems................................................6 Drivers.....................................................6 Platforms...................................................9 Kernel subsystems...........................................9 Security...................................................10 Userland...................................................11 Components removed from NetBSD.............................12 The Future of NetBSD..........................................13 Sources of NetBSD.............................................13 NetBSD 4.0.1 Release Contents.................................13 NetBSD/evbppc subdirectory structure.......................15 Binary distribution sets...................................15 NetBSD/evbppc System Requirements and Supported Devices.......17 Supported devices..........................................17 Unsupported devices........................................17 Supported boot devices and media...........................17 Getting the NetBSD System on to Useful Media..................18 Preparing your System for NetBSD installation.................20 Booting over a serial line.................................20 Booting from the network...................................20 Installing the NetBSD System..................................24 Booting the installer......................................24 Example of a normal boot...................................24 Common Problems and Error Messages.........................24 Running the sysinst installation program...................25 Introduction............................................25 Possible hardware problems..............................25 General.................................................25 Quick install...........................................25 Booting NetBSD..........................................26 Network configuration...................................26 Installation drive selection and parameters.............26 Partitioning the disk...................................27 Preparing your hard disk................................27 Getting the distribution sets...........................27 Installation using ftp..................................28 Installation using NFS..................................28 Installation from CD-ROM................................28 Installation from an unmounted file system..............28 Installation from a local directory.....................28 Extracting the distribution sets........................29 Finalizing your installation............................29 Post installation steps.......................................29 Upgrading a previously-installed NetBSD System................32 Compatibility Issues With Previous NetBSD Releases............32 Issues affecting an upgrade from NetBSD 2.1 and older......32 Issues affecting an upgrade from NetBSD 3.x releases.......33 Issues with GDB 6.5...........................................33 Using online NetBSD documentation.............................34 Administrivia.................................................34 Thanks go to..................................................35 We are........................................................35 Legal Mumbo-Jumbo.............................................41 The End.......................................................47 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 4.0.1 on the evbppc platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX-like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on fifty four different system architectures (ports), featuring sev- enteen machine architectures across fifteen distinct CPU families, and is being ported to more. The NetBSD 4.0.1 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distri- bution. Please see the NetBSD web site at http://www.NetBSD.org/ for information on them.) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Changes Between The NetBSD 4.0 release and 4.0.1 update The NetBSD 4.0.1 update is the first security/critical update of the NetBSD 4.0 release branch. This represents a selected subset of fixes deemed critical in nature for stability or security reasons. These fixes will also appear in future releases (NetBSD 4.1), together with other less-critical fixes and feature enhancements. The complete list of changes can be found in the CHANGES-4.0.1: ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-4.0.1/CHANGES-4.0.1 file in the top level directory of the NetBSD 4.0.1 release tree. Security Advisories Fixes o NetBSD-SA2008-004, bzip2(1) Multiple issues (CVE-2008-1372 and CVE-2005-0953), has been fixed by upgrading bzip2 to 1.0.5. o NetBSD-SA2008-005, OpenSSH Multiple issues (CVE-2008-1483 and CVE-2008-1657), has been fixed by applying patches from upstream. o NetBSD-SA2008-006, Integer overflow in strfmon(3) function (CVE-2008-1391), has been fixed. o NetBSD-SA2008-008, OpenSSL Montgomery multiplication (CVE-2007-3108), has been fixed. o NetBSD-SA2008-009, BIND cache poisoning (CVE-2008-1447 and CERT VU#800113), has been fixed by updating BIND to 9.4.2-P2. Note there are two related changes to this advisory: - The default behavior of ipfilter's Port Address Translation has been changed to using random port allocation rather than sequen- tial mappings, to avoid decreasing the randomness of source ports used for DNS queries which affects the BIND cache poisoning prob- lem. - A `query-source' statement, which could allow the BIND cache poi- soning attack, has been commented out in the default named.conf(5) file. o NetBSD-SA2008-010, Malicious PPPoE discovery packet can overrun a kernel buffer (CVE-2008-3584), has been fixed. o NetBSD-SA2008-011, ICMPv6 MLD query (CVE-2008-2464), has been fixed. o NetBSD-SA2008-012, Denial of Service issues in racoon(8) (CVE-2008-3652), has been fixed by upgrading ipsec-tools to release 0.7.1. Note this also fixes CVE-2008-3651. o upcoming NetBSD-SA2008-013, IPv6 Neighbor Discovery Protocol routing vulnerability (CVE-2008-2476), has been fixed. o upcoming NetBSD-SA2008-014, Remote cross-site request forgery attack issue in ftpd(8) (CVE-2008-4247), has been fixed. o upcoming NetBSD-SA2008-015, Remote kernel panics on IPv6 connections (CVE-2008-3530), has been fixed. Note: NetBSD-SA2008-007 and advisories prior to NetBSD-SA2008-004 don't affect NetBSD 4.0. Other Security Fixes o Fix a buffer overrun which could crash a FAST_IPSEC kernel. o tcpdump(8): Fix CVE-2007-1218, CVE-2007-3798 and CAN-2005-1278 in base-tcpdump. o Fix a buffer overflow of PCF font parser in X11 libXfont library (CVE-2008-0006). o Fix a buffer overflow of Tektronix Hex Format support in binutils (CVE-2006-2362). o machfb(4), voodoofb(4): Introduce two missing KAUTH_GENERIC_ISSUSER check in the mmap(2) code. Networking o Update root.cache to 2008020400 version. o Fix IP packet forwording code to make sure to send a reasonable frag- ment size when IPSEC is configured. o Fix a bug in TCP SACK code which causes data corruption. o Fix an rc.d(8) script for amd(8) not to shutdown gracefully since it seems to cause problems for more people than the old (also broken) behavior. o ftpd(8): Fix and reorganize PAM support. Libraries o Pthread support of BIND has been disabled for future binary compati- bility after removal of the scheduler activations. o Fix coredump of gdtoa (conversion between binary floating-point and ASCII string) functions on out of memory conditions. Drivers o fxp(4): Fix random pool corruption and hangup problems. o wd(4): Handle more LBA48 bug quirks on some Hitachi's SATA/IDE drives. Miscellaneous o Disable a NULL pointer check in zlib for standalone programs. This fixes errors on loading a gzipped kernel (including installation ker- nels) on several ports (news68k etc.) whose kernels are loaded at address zero. o awk(1): Bring back an accidentally removed fix to allow escape of a newline in string literals. o gcc(1): - Fix compilation of native sh3 gcc on 64-bit build machines. - Fix an internal compiler error on compiling m68k softfloat or m68010 targets on 64-bit build machines. o zgrep(1): Make `-h' option (suppress filenames on output when multiple files are searched) actually work. o Fix parallel build failure on building hpcarm, hpcmips and hpcsh releases. Platforms specific o acorn32: Fix a bootloader problem on some RiscPCs. o cobalt: - Add a workaround to avoid panic on probing a multi function PCI device on Qube's PCI slot. - Fix a bug in the interrupt handler which causes network freeze if more than one interfaces are used. o hp700: Fix potential kernel / userland memory corruption in copyinstr(9) and copyoutstr(9). o sparc64: Fix a bug in locore.s which causes unexpected behavior. o sun3: Fix a bug which might cause an occasional panic during boot. o vax: Make syscall handler use proper copyin(9) function on parsing syscall args. Changes Between The NetBSD 3.0 and 4.0 Releases The NetBSD 4.0 release provides numerous significant functional enhance- ments, including support for many new devices, integration of hundreds of bug fixes, new and updated kernel subsystems, and many user-land enhance- ments. The result of these improvements is a stable operating system fit for production use that rivals most commercially available systems. It is impossible to completely summarize more than a year of development that went into the NetBSD 4.0 release. The complete list of changes can be found in the CHANGES: ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-4.0/CHANGES and CHANGES-4.0: ftp://ftp.NetBSD.org/pub/NetBSD/NetBSD-4.0/CHANGES-4.0 files in the top level directory of the NetBSD 4.0 release tree. Some highlights include: Networking o agr(4): new pseudo-device driver for link level aggregation. o IPv6 support was extended with an RFC 3542-compliant API and added for gre(4) tunnels and the tun(4) device. o A NDIS-wrapper was added to use Windows binary drivers on the i386 platform, see ndiscvt(8). o The IPv4 source-address selection policy can be set from a number of algorithms. See "IPSRCSEL" in options(4) and in_getifa(9). o Imported wpa_supplicant(8) and wpa_cli(8). Utilities to connect and handle aspects of 802.11 WPA networks. o Imported hostapd(8). An authenticator for IEEE 802.11 networks. o carp(4): imported Common Address Redundancy Protocol to allow multi- ple hosts to share a set of IP addresses for high availability / redundancy, from OpenBSD. o ALTQ support for the PF packet filter. o etherip(4): new EtherIP tunneling device. It's able to tunnel Ether- net traffic over IPv4 and IPv6 using the EtherIP protocol specified in RFC 3378. o ftpd(8) can now run in standalone mode, instead of from inetd(8). o tftp(1) now has support for multicast TFTP operation in open-loop mode, server is in progress. o tcp(4): added support for RFC 3465 Appropriate Byte Counting (ABC) and Explicit Congestion Notification as defined in RFC 3168. File systems o scan_ffs(8), scan_lfs(8): utilities to find FFSv1/v2 and LFS parti- tions to recover lost disklabels on disks and image files. o tmpfs: added a new memory-based file system aimed at replacing mfs. Contrary to mfs, it is not based on a disk file system, so it is more efficient both in overall memory consumption and speed. See mount_tmpfs(8). o Added UDF support for optical media and block devices, see mount_udf(8). Read-only for now. o NFS export list handling was changed to be filesystem independent. o LFS: lots of stability improvements and new cleaner daemon. It is now also possible to use LFS as root filesystem. o vnd(4): the vnode disk driver can be used on filesystems such as smbfs and tmpfs. o Support for System V Boot File System was added, see newfs_sysvbfs(8) and mount_sysvbfs(8). Drivers o Audio: - Support for new models on drivers such as Intel ICH8/6300ESB, NVIDIA nForce 3/4, etc. - Added support for AC'97 modems. - auich(4): added support to handle the AC'97 modem as audio device, enabled with the kernel option ``AUICH_ATTACH_MODEM'' - azalia(4): added support for S/PDIF. o Hardware Monitors: - amdpm(4): added support for the i2c bus on the AMD-8111 used on many Opteron motherboards and for the Analog Devices ADT7464 hardware monitor chip. - adt7467c(4): new driver for Analog Devices ADT7467 and ADM1030 hardware monitor chips. - ipmi(4): new driver for motherboards implementing the Intelligent Platform Management Interface 1.5 or 2.0, from OpenBSD. - it(4): new driver for iTE 8705F/8712F and SiS 950 hardware moni- tors. - The lm(4) driver was rewritten and support for more chips was added, for example for Winbond W83627HF, W83627THF, W83627DHG and Asus AS99127F. - owtemp(4): new driver for the 1-Wire temperature sensors. - tmp121temp(4): new driver for the Texas Instruments TMP121 tem- perature sensor. - ug(4): new driver for Abit uGuru hardware monitor found on newer Abit motherboards. o Miscellaneous: - geodewdog(4): new AMD Geode SC1100 Watchdog Timer driver. - gscpcib(4): new AMD Geode SC1100 PCI-ISA bridge that provides support for the GPIO interface. o Networking: - ath(4): updated HALs with support for WiSOC (AR531x) and 32bit SPARC. - bge(4): added support for the following chips: BCM5753, BCM5753M, BCM5715, BCM5754, BCM5755 and BCM5787. Numerous improvements and bugfixes were made too. - kse(4): new driver for Micrel KSZ8842/8841 PCI network cards. - msk(4): new driver for Marvell Yukon 2 GigE PCI network cards, from OpenBSD. - nfe(4): new driver for NVIDIA nForce Ethernet network cards, from OpenBSD. - ral(4): new 802.11 driver for PCI/Cardbus Ralink RT2500, RT2501, RT2600, RT2661 and RT2500 USB chipsets, from OpenBSD. - rum(4): new 802.11 driver for USB Ralink RT2501 and RT2601 chipsets, from OpenBSD. - sip(4): now works on sparc64. - tlp(4): added support for ASIX AX88140A and AX88141. - vr(4): added support for the VIA Rhine III. - wm(4): added support for i8003, ICH8, ICH9 and others. Support for IPv6 Rx TCP/UDP Checksum Offloading and more. - wpi(4): new driver for Intel PRO/Wireless 3945ABG PCI 802.11 net- work cards, from OpenBSD. o Security: - glxsb(4): new driver for the AMD Geode LX AES Security Block that provides random numbers and AES acceleration, from OpenBSD. o Power Management: - Support for Intel Speedstep SMI on PIIX4 PCI-ISA for i386. - Support for AMD PowerNow and Cool'n'Quiet Technology on K7 and K8 CPUs (both in 32 and 64 bit mode), including Athlon Mobile, Athlon64, Opteron or X2. See options(4) for more information. - Support for more Enhanced Speedstep CPUs, including VIA C7/Eden and Intel Core Solo/Duo/Duo2. See options(4) for more informa- tion. - The Enhanced Speedstep and PowerNow drivers were modified to be able to be scaled in all CPUs available, saving power on SMP sys- tems. o Storage: - ahcisata(4): new driver for AHCI 1.0 and 1.1 compliant SATA con- trollers. - ataraid(4): added support to handle Adaptec HostRAID and VIA V- Tech software RAID. - ciss(4): new driver for HP/Compaq 5th+ generation Smart ARRAY controllers, from OpenBSD. - fdc(4): added support for SBus based sparc64 machines and fixed formatting on sparc. - gcscide(4): new driver for the AMD Geode CS5535 Companion Device IDE controller. - jmide(4): new driver for JMicron Technology JMB36x PCIe to SATA II/PATA controllers. - mfi(4): new driver for LSI Logic and Dell MegaRAID SAS con- trollers, from OpenBSD. - mpt(4): added support for newer SAS and similar devices. - njata(4): new driver for Workbit NinjaATA-32 CardBus IDE con- troller. - pdcsata(4): added support for the Promise PDC20775, PDC20771, PDC40518, PDC40718 and some bugfixes. - piixide(4): added support for some ICH8/ICH8-M/ICH9 IDE and SATA controllers. - svwsata(4): new driver for Serverworks K2 SATA controllers, from OpenBSD. - viaide(4) added support for the VIA VT8237A SATA controller and AMD CS5536 Companion Device IDE Controller. o USB: - ucycom(4): new driver for Cypress microcontroller based serial devices. - uipaq(4): new driver for the iPAQ devices. - uslsa(4): new driver for Silicon Labs CP210x series serial adapters. - utoppy(4): new driver for the Topfield TF5000PVR range of digital video recorders. Platforms o i386: - Added support for the for Multiboot specification. This means much improved support for loading the kernel by GRUB, including passing in parameters to the kernel. - Added the unichromefb framebuffer driver that supports the VIA Unichrome Graphics adapter. - vesafb(4): added new framebuffer driver that supports VESA BIOS (VBE) 2.0 extensions and up. - Added cd9660 file system support to the BIOS bootloader. o evbarm: new platform support for Arcom Viper PXA255-based single board, Atmark Techno Armadillo-9 and Armadillo-210, Certance CP-3100, Linksys NSLU2 (a.k.a. "Slug") and I-O DATA HDL-G Giga LANDISK NAS devices. o evbmips: added support for Alchemy Au1550 processors, DBAu1550 boards, Alchemy Au15XX PCI host, (OMS-AL400/128) and Atheros AR5312 SoC. o New port ews4800mips: NEC's MIPS based EWS4800 workstations. o cobalt: added support for booting off raidframe RAID1 mirrors. o hpcmips: added the teliosio(4) driver for the Sharp Telios LCD screen and Battery unit. o New port landisk: port to the SH4 processor based NAS appliances, supporting models by I-O DATA (USL-5P, HDL-U, HDL-AV, HDL-W and HDLM- U series, SuperTank LAN Tank, UHDL-160U and UHDL-300U) and Plextor PX-EH16L, PX-EH25L and PX-EH40L. o macppc: this port has gained support to use accelerated wsdisplay drivers by default (if possible), and uses the appropriate driver rather than the Generic Open Firmware Framebuffer. o prep: this port has been modernized, and support for five additional machines has been added, among them the IBM 7024-E20 and 7025-F30 models and Motorola Powerstack E1. Additionally, sysinst support was added, and the bootloader process was improved, allowing easy instal- lation and upgrade to future releases. o sparc: added support for booting off raidframe RAID1 mirrors. o Xen: support for Xen3 domU and dom0 (Unprivileged domain and domain 0), including support for hardware virtualization on CPUs that sup- port it. Kernel subsystems o Improved Firewire (IEEE1394) support imported from FreeBSD. o The midi(4) framework got a complete overhaul for better support of Active Sensing and improved handling of tempo and timebase changes. o Added a Bluetooth protocol stack including: - hardware drivers: ubt(4) for USB controllers, and bt3c(4) for the 3Com Bluetooth PC-Card. - socket based access to the HCI, L2CAP, RFCOMM and SCO protocols. - pseudo drivers for integrating services on remote Bluetooth devices such as Keyboards, Mice and SCO Audio into the NetBSD device framework. See bluetooth(4), bthset(1) and btpin(1). o Imported the bio(4) framework from OpenBSD, to query/control block hardware RAID device controllers. Currently supporting the mfi(4) driver. o Kernel uses stateful read-ahead algorithm. o dkctl(8) can be used to switch buffer queuing strategies on the fly on wd(4) disks, see also bufq(9). o fileassoc(9) is used by Veriexec, it adds in-kernel and file-system independent file meta-data association interface. o firmload(9): an API for loading firmware images used by various hard- ware devices. o gpio(4): imported General Purpose I/O framework from OpenBSD. o onewire(4): imported Dallas Semiconductor 1-wire bus framework from OpenBSD. o The proplib(3) protocol was added for sending property lists to/from the kernel using ioctls. o spi(4): new SPI (Serial Peripherial Interface) framework. o timecounter(9) adds a new time-keeping infrastructure along with NTP API 4 nanokernel implementation. Almost all platforms were changed to support this API. o Start of 32bit-Linux-emulation for amd64 (COMPAT_LINUX32). o wscons(4) console driver supports splash screens, scrolling, progress bar for kernel and boot messages. Kernel interfaces have continued to be refined, and more subsystems and device drivers are shared among the different ports. You can look for this trend to continue. Security o The FAST_IPSEC IPsec implementation was extended to use hardware acceleration for IPv6, in addition to the hardware accelerated IPv4 that was available before. See fast_ipsec(4) for more information. o mprotect(2) got restrictions to enforce W^X policies, from PaX. See options(4), sysctl(3), and paxctl(1). o GCC 4's support for stack smashing protection (SSP) was enabled by adding libssp, see security(8). o The kernel authorization framework kauth(9) was added, replacing the traditional BSD credential management and privileged operation access control with an abstract layer, allowing the implementation of vari- ous security models either as part of the NetBSD distribution or as third-party LKMs. NetBSD's kernel authorization is a hybrid clean-room implementation of a similar interface developed by Apple, extending its capabilities and combining concepts of credential inheritance control. Userland o 3rd party software updates: - BIND 9.4.1-P1 - OpenSSL 0.9.8e - CVS 1.11.22 - OpenSSH 4.4 - gettext 0.14.4 - PF from OpenBSD 3.7 - (n)awk 20050424 - Postfix 2.4.5 - am-utils 6.1.3 - file 4.21 - zlib 1.2.3 - GNU binutils 2.16.1 - GNU groff 1.19.2 - IPFilter 4.1.23 - GNU gcc 4.1.2 prerelease - GNU gdb 6.5 (some architectures) - NTP 4.2.4p2 - pppd 2.4.4 o cdplay(1): added digital transfer mode support. o cksum(1) can now verify checksums. o csplit(1): new utility that splits a file into pieces. From FreeBSD/OpenBSD. o identd(1): added support for forwarding ident queries and receiving of proxied ident queries. o getent(1): added support for the ethers database. o gkermit(1): new program for transferring files using the Kermit pro- tocol. o mail(1): added support for Mime and multi-character set handling, command line editing and completion. o utoppya(1): new utility to interface to the utoppy(4) driver. o init(8): added support for running multi-user in a chroot() environ- ment. Allows / file system on e.g., cgd(4), vnd(4) or ccd(4) volumes. o gpt(8): new GUID partition table maintenance utility, from FreeBSD. o iSCSI target (server) code added, see iscsi-target(8); Initiator (client) code is underway. o lockstat(8): new command to display a summary of kernel locking events recorded over the lifetime of a called program. o ofctl(8): new command to display the OpenPROM or OpenFirmware device tree for the macppc, shark and sparc64. o Various utilities to support Bluetooth were added: - btconfig(8) for controller configuration. - btdevctl(8) to manage pseudo devices relating to remote services. - bthcid(8) and btpin(1) for authenticating radio connections. - sdpd(8) for providing service discovery to remote devices. - sdpquery(1) for querying services on remote devices. - rfcomm_sppd(1) to access remote services over RFCOMM via stdio or pty. - bthset(1) for making connections to Bluetooth headsets. Besides this list, there have also been innumerable bug fixes and other miscellaneous enhancements of course. Components removed from NetBSD In this release of NetBSD, some software components known from previous releases were removed from the system. In some cases those were compo- nents that are not useful anymore or their utility does not justify main- tenance overhead. Other components were not working properly and there was lack of interest in fixing them. o Sushi was removed from the base system due to lack of interest and maintenance. If you really want it, it is available in the CVS repos- itory at othersrc/usr.sbin/sushi. However, be warned that it is unmaintained and is most likely out of date. o Vinum was removed due to lack of interest and maintenance. At the time of removal, it had several known serious issues (including not being compilable). RAIDframe provides similar functionality. If you were using Vinum you will need to back up your data, delete the Vinum partitions, create RAIDframe partitions, and restore your data to them. Details about RAIDframe can be found in raid(4), raidctl(8), and the NetBSD Guide: http://www.NetBSD.org/docs/guide/en/chap-rf.html. o Sendmail was removed. Postfix is the MTA and provides the sendmail(1) command line tool. Postfix has been included with NetBSD since NetBSD 1.5 was released in December 2005. Details about Postfix can be found in the NetBSD Guide: http://www.NetBSD.org/docs/guide/en/chap-mail.html. For those who need Sendmail, it is available from pkgsrc in the mail/sendmail and mail/sendmail813 packages. o NETCCITT and NETNS were removed due to lack of interest and mainte- nance. They had known serious issues (including being out of date with respect to other network code) and there were no known users at the time of their removal. Unfortunately, there is no replacement or option for them. o UUCP was removed. The NetBSD improvements were merged into the pkgsrc version. For those who use UUCP tools, they are available from pkgsrc in the net/uucp package. The cu(1) command is available as a frontend to tip(1). o The Fortran 77 compiler ( g77 ) has been removed with the transition from GCC 3 to GCC 4, which does not include it. For those who need it, it is available from pkgsrc in the lang/gcc3-f77 package. o The evbsh5 port has been removed from NetBSD due to lack of interest, compounded by a lack of available SH5 hardware. The Future of NetBSD The NetBSD Foundation has been incorporated as a non-profit organization. Its purpose is to encourage, foster and promote the free exchange of com- puter software, namely the NetBSD Operating System. The foundation will allow for many things to be handled more smoothly than could be done with our previous informal organization. In particular, it provides the framework to deal with other parties that wish to become involved in the NetBSD Project. The NetBSD Foundation will help improve the quality of NetBSD by: o providing better organization to keep track of development efforts, including co-ordination with groups working in related fields. o providing a framework to receive donations of goods and services and to own the resources necessary to run the NetBSD Project. o providing a better position from which to undertake promotional activities. o periodically organizing workshops for developers and other interested people to discuss ongoing work. We hope to support even more hardware in the future, and we have a rather large number of other ideas about what can be done to improve NetBSD. We intend to continue our current practice of making the NetBSD-current development source available on a daily basis. We intend to integrate free, positive changes from whatever sources sub- mit them, providing that they are well thought-out and increase the usability of the system. Above all, we hope to create a stable and accessible system, and to be responsive to the needs and desires of NetBSD users, because it is for and because of them that NetBSD exists. Sources of NetBSD Refer to http://www.NetBSD.org/mirrors/. NetBSD 4.0.1 Release Contents The root directory of the NetBSD 4.0.1 release is organized as follows: .../NetBSD-4.0.1/ CHANGES Changes between NetBSD 3.0 and branching 4.0. CHANGES-4.0 Changes since NetBSD 4.0 was branched. CHANGES-4.0.1 Changes between NetBSD 4.0 and 4.0.1. CHANGES.prev Changes in earlier NetBSD releases. LAST_MINUTE Last minute changes. MIRRORS A list of sites that mirror the NetBSD 4.0.1 distribution. README.files README describing the distribution's contents. TODO NetBSD's todo list (also somewhat incomplete and out of date). patches/ Post-release source code patches. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 4.0.1 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. 95 MB gzipped, 484 MB uncompressed sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. 6 MB gzipped, 25 MB uncompressed src This set contains all of the base NetBSD 4.0.1 sources which are not in gnusrc, sharesrc, or syssrc. 45 MB gzipped, 214 MB uncompressed syssrc This set contains the sources to the NetBSD 4.0.1 kernel for all architectures; config(1); and dbsym(8). 33 MB gzipped, 165 MB uncompressed xsrc This set contains the sources to the X Window System. 95 MB gzipped, 502 MB uncompressed All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # cd / ; tar -zxpf set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: BSDSUM Historic BSD checksums for the various files in that directory, in the format produced by the command: cksum -o 1 file. CKSUM POSIX checksums for the various files in that directory, in the format produced by the command: cksum file. MD5 MD5 digests for the various files in that directory, in the format produced by the command: cksum -a MD5 file. SHA512 SHA512 digests for the various files in that directory, in the format produced by the command: cksum -a SHA512 file. SYSVSUM Historic ATT System V UNIX checksums for the various files in that directory, in the format produced by the command: cksum -o 2 file. The SHA512 digest is the safest checksum, followed by the MD5 digest, and finally the POSIX checksum. The other two checksums are provided only to ensure that the widest possible range of systems can check the integrity of the release files. NetBSD/evbppc subdirectory structure The evbppc-specific portion of the NetBSD 4.0.1 release is found in the evbppc subdirectory of the distribution: .../NetBSD-4.0.1/evbppc/. It contains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-WALNUT.gz A gzipped NetBSD kernel (in ELF format) containing code for everything sup- ported in this release. netbsd.img-WALNUT.gz Same as the above, but in the format expected by the firmware. netbsd-INSTALL_WALNUT.gz A gzipped NetBSD kernel (ELF format) containing code for everything sup- ported in this release. It also includes a RAM-disk installer with sysinst. netbsd-INSTALL_WALNUT.img.gz Same as the above, but in the format expected by the firmware. sets/ evbppc binary distribution sets; see below. installation/ Binary distribution sets The NetBSD evbppc binary distribution sets contain the binaries which comprise the NetBSD 4.0.1 release for the evbppc. The binary distribution sets can be found in the evbppc/binary/sets subdirectory of the NetBSD 4.0.1 distribution tree, and are as follows: base The NetBSD 4.0.1 evbppc base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally functional. It includes shared library support, and excludes everything described below. 26 MB gzipped, 75 MB uncompressed comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. 31 MB gzipped, 106 MB uncompressed etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. 1 MB gzipped, 1 MB uncompressed games This set includes the games and their manual pages. 4 MB gzipped, 8 MB uncompressed kern-WALNUT This set contains a NetBSD/evbppc 4.0.1 kernel in ELF format named /netbsd and the same kernel in the format needed by the bootloader as /netbsd.img. These kernels are specific to the IBM 405GP based Wal- nut evaluation board. You must install this distribution set. 5 MB gzipped, 9 MB uncompressed man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. 8 MB gzipped, 33 MB uncompressed misc This set includes the (rather large) system dictionaries, the type- settable document set, and other files from /usr/share. 4 MB gzipped, 12 MB uncompressed text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. 4 MB gzipped, 11 MB uncompressed NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86, and tightly track XFree86 releases. They are currently equivalent to XFree86 4.5.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. 7 MB gzipped, 20 MB uncompressed xcomp The extra libraries and include files needed to compile X source code. 13 MB gzipped, 44 MB uncompressed xfont Fonts needed by the X server and by X clients. 31 MB gzipped, 39 MB uncompressed xetc Configuration files for X which could be locally modified. 0.03 MB gzipped, 0.17 MB uncompressed xserver The X server. 5 MB gzipped, 11 MB uncompressed The evbppc binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the file- names stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xpf command from the root directory ( / ) of your system. This util- ity is used only in a Traditional method installation. Note: Each directory in the evbppc binary distribution also has its own checksum files, just as the source distribution does. NetBSD/evbppc System Requirements and Supported Devices NetBSD/evbppc is a port of NetBSD to PowerPC based evaluation board. At the present time, the IBM PowerPC 405GP based walnut evaluation board is the only board supported by this port. As a result, this documentation is specific to installing NetBSD/evbppc on that particular piece of hardware. More evalua- tion boards will be added in due course, and this documentation will be updated accordingly. Supported devices o Ethernet: The built-in Ethernet card is not supported, so another PCI Ethernet card supported by NetBSD must be provided if you want to use NetBSD/evbppc on a network. Any PCI Ethernet card supported by NetBSD should work. o SCSI: Any PCI SCSI card supported by NetBSD should work, as should most SCSI disk/tape/CD-ROM devices. o IDE: - Promise Ultra66 (pciide) - Other PCI IDE controllers should work, but there are no reports. - Most IDE disk/CD-ROM/ATAPI devices should work. o Audio - PCI audio cards, although none have been tested. o Serial ports - On-board serial ports (com0) and (com1) - Some PCI serial ports should work, but no one has tried them o PCI cards - Most MI PCI cards should work, although very few have been tested with NetBSD/evbppc http://www.NetBSD.org/support/hardware/pci.html Unsupported devices o On-board Ethernet Note: This does not concern booting the kernel itself, since that is done by the firmware. For using an NFS root you will have to pro- vide a supported network card, though. Supported boot devices and media The firmware only supports booting from network or the serial port, so you cannot boot from disk even if you install a disk controller. Instructions for booting from serial port are not provided; in the following we will describe how to setup netbooting. The first step is setting the IP addresses of both the walnut itself and the host that will be serving the kernel image. From the main menu, choose 3 to set the IP address of the machine: 1 - Enable/disable tests 2 - Enable/disable boot devices 3 - Change IP addresses 4 - Ping test 5 - Toggle ROM monitor debugger 6 - Toggle automatic menu 7 - Display configuration 8 - Save changes to configuration 9 - Set baud rate for s1 boot A - Enable/disable I cache (Enabled ) B - Enable/disable D cache (Enabled ) 0 - Exit menu and continue -> 3 Set the IP address for the local Ethernet with 1: --- CHANGE IP ADDRESS --- Device List: 001 Enabled Ethernet [ENET] local=0.0.0.0 remote=0.0.0.0 hwaddr=0004ace312bd 004 Disabled Serial Port 2 [S2] local=8.1.1.2 remote=255.255.255.255 hwaddr=ffffffffffff ---------------------------- select device to change ->1 1 - Change local address 2 - Change remote address 0 - Return to main menu ->1 Current IP address = (0.0.0.0) Enter new IP address ->Enter IP address in dot notation, (eg. 8.1.1.2) Here you enter the machine's IP address, e.g. 10.0.0.1. Now you need to do the same thing to set the host IP address (choice 2 from the menu above). Once both the local and remote addresses are set, you can use the ping test to make sure the ethernet is working; or you can simply use option 0, "Exit menu and continue" to try to boot the machine, if you already set up the remote machine to provide a kernel image. For details on how to do that, see the Booting from the network section below. You should now be able to boot the operating system. Getting the NetBSD System on to Useful Media Note that if you are installing or upgrading from a writable media, the media can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted. Installation is supported from several media types, including: o CD-ROM / DVD o MS-DOS floppy o FTP o Remote NFS partition o Tape o Existing NetBSD partitions, if performing an upgrade The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the various media are outlined below. CD-ROM / DVD Find out where the distribution set files are on the CD-ROM or DVD. Likely locations are binary/sets and evbppc/binary/sets. Proceed to the instruction on installation. MS-DOS floppy NetBSD doesn't include split sets to keep the distribution size down. They can be created on a separate machine using the split(1) command, running e.g. split -b 235k base.tgz base. to split the base.tgz file from evbppc/binary/sets into files named base.aa, base.ab, and so on. Repeat this for all set_name.tgz files, splitting them into set_name.xx files. Count the number of set_name.xx files that make up the distri- bution sets you want to install or upgrade. You will need one sixth that number of 1.44 MB floppies. Format all of the floppies with MS-DOS. Do not make any of them bootable MS-DOS floppies, i.e. don't use format /s to for- mat them. (If the floppies are bootable, then the MS-DOS sys- tem files that make them bootable will take up some space, and you won't be able to fit the distribution set parts on the disks.) If you're using floppies that are formatted for MS-DOS by their manufacturers, they probably aren't bootable, and you can use them out of the box. Place all of the set_name.xx files on the MS-DOS disks. Once you have the files on MS-DOS disks, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. FTP The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. If you don't have access to a functioning nameserver during installation, the IPv4 address of ftp.NetBSD.org is 204.152.190.13 and the IPv6 address is 2001:4f8:4:7:230:48ff:fe31:43f2 (as of December, 2007). Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. Note: This method of installation is recommended for those familiar with using BSD network configuration and man- agement commands. If you aren't, this documentation should help, but is not intended to be all-encompassing. NFS Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the /etc/exports file on the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privileges on the server.) You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once the NFS server is set up properly and you have the infor- mation mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Note: This method of installation is recommended for those already familiar with using BSD network configuration and management commands. If you aren't, this documenta- tion should help, but is not intended to be all-encom- passing. Tape To install NetBSD from a tape, you need to make a tape that contains the distribution set files, in `tar' format. If you're making the tape on a UNIX-like system, the easiest way to do so is probably something like: # tar -cf tape_device dist_directories where tape_device is the name of the tape device that describes the tape drive you're using; possibly /dev/rst0, or something similar, but it will vary from system to system. (If you can't figure it out, ask your system administrator.) In the above example, dist_directories are the distribution sets' directo- ries, for the distribution sets you wish to place on the tape. For instance, to put the kern-GENERIC, base, and etc distribu- tions on tape (in order to do the absolute minimum installation to a new disk), you would do the following: # cd .../NetBSD-4.0.1 # cd evbppc/binary # tar -cf tape_device kern-GENERIC base etc Note: You still need to fill in tape_device in the example. Once you have the files on the tape, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing instal- lation, go directly to the section on upgrading. Preparing your System for NetBSD installation When installing NetBSD for your NetBSD/evbppc system, you have two options: Via serial port or via network. The firmware does not support loading the kernel from a disk. Booting over a serial line This is not currently documented or supported. If you would like to attempt this and supply documentation, please do! Booting from the network 1. Introduction To netboot a evbppc, you must configure one or more servers to provide information and files to your evbppc (the `client'). If you are using NetBSD (any architecture) on your netboot server(s), the information pro- vided here should be sufficient to configure everything. Additionally, you may wish to look at the diskless(8) manual page and the manual pages for each daemon you'll be configuring. If the server(s) are another operating system, you should consult the NetBSD Diskless HOW-TO, which will walk you through the steps necessary to configure the netboot ser- vices on a variety of platforms. http://www.NetBSD.org/docs/network/netboot/ You may either netboot the installer so you can install onto a locally attached disk, or you may run your system entirely over the network. Briefly, the netboot process involves discovery, kernel and file system stages. In the first stage, the client discovers information about where to find the kernel image. Once the kernel is loaded, it starts execut- ing. For RAM disk kernels, it mounts the RAM disk file system and begins executing the installer from the RAM disk. For normal (non-RAM disk) kernels, the kernel tries to mount the NFS share that had the kernel and starts executing the installation tools or init(8). All evbppc systems use BOOTP for the discovery stage. TFTP is used in the bootstrap phase to download the kernel via the on-board Ethernet card by the firmware. Thus, NetBSD support for the on-board card is not needed in this step. For NFS mounting a file system on the other hand, NetBSD support for the Ethernet card is needed, and the on-board one will not suffice; you have to provide a second Ethernet card supported by NetBSD . We will use `CC:CC:CC:CC:CC:CC' as the MAC address (ethernet hardware address) of your netboot client machine. You should have determined this address in an earlier stage. In this example, we will use `192.168.1.10' as the IP address of your client and `client.test.net' as its name. We will assume you're providing all of your netboot services on one machine called `server.test.net' with the client's files exported from the direc- tory /export/client/root. You should, of course, replace all of these with the names, addresses, and paths appropriate to your environment. You should set up each netboot stage in order (i.e. discovery, bootstrap, kernel, and then file system) so that you can test them as you proceed. 2. dhcpd(8) in bootpd(8) compatible mode Put the following lines in your /etc/dhcpd.conf (see dhcpd.conf(5) and dhcp-options(5) for more information): ddns-update-style none; # Do not use any dynamic DNS features # allow bootp; # Allow bootp requests, thus the dhcp server # will act as a bootp server. # authoritative; # master DHCP server for this subnet # subnet 192.168.1.0 netmask 255.255.255.0 { # Which network interface to listen on. # The zeros indicate the range of addresses # that are allowed to connect. } group { # Set of parameters common to all clients # in this "group". # option broadcast-address 192.168.1.255; option domain-name "test.net"; option domain-name-servers dns.test.net; option routers router.test.net; option subnet-mask 255.255.255.0; # # An individual client. # host client.test.net { hardware ethernet CC:CC:CC:CC:CC:CC; fixed-address 192.168.1.10; # # Name of the host (if the fixed address # doesn't resolve to a simple name). # option host-name "client"; # # Name of the kernel image to download via tftp. # Note: Plain (ELF) kernels won't work, you # have to use the corresponding *.img file. # filename "netbsd-INSTALL_WALNUT.img" # # Name of the bootloader or kernel # to download via tftp. # # The path on the NFS server. # option root-path "/export/client/root"; # # If your DHCP server is not your NFS server, supply the # address of the NFS server. Since we assume you run everything # on one server, this is not needed. # # next-server server.test.net; } #you may paste another "host" entry here for additional #clients on this network } You will need to make sure that the dhcpd.leases file exists. # touch /var/db/dhcpd.leases You will need to start the dhcpd. If it's already running, you will need to restart it to force it to re-read its configuration file. If the server is running NetBSD, you can achieve this with: # /etc/rc.d/dhcpd restart 3. tftpd(8) The default configuration of the TFTP server is to run in a chroot(8) environment in the /tftpboot directory. Thus, the first order of busi- ness is to create this directory: # mkdir -p /tftpboot Next, edit /etc/inetd.conf and uncomment the line with the TFTP daemon: tftp dgram udp wait root /usr/libexec/tftpd tftpd -l -s /tftpboot Now, restart inetd(8). If the server is running NetBSD, you can achieve this with: # /etc/rc.d/inetd restart Now, you need to copy the kernel for your evbppc machine to /tftpboot. Just to be sure, let's make everything readable. # chmod -R a+rX /tftpboot Sometimes, the arp(8) table gets messed up, and the TFTP server can't communicate with the client. In this case, it will write a log message (via syslogd(8)) to /var/log/messages saying: `tftpd: write: Host is down'. If this is the case, you may need to force the server to map your client's ethernet address to its IP address: # arp -s client CC:CC:CC:CC:CC:CC 4. nfsd(8), mountd(8), and rpcbind(8) You can either boot a kernel, or the RAM disk-based installer binary/kernel/netbsd-INSTALL.img.gz. In the first case you'll also need an NFS-mounted userland. Let's set up the NFS server. Create the direc- tory you are exporting for the netboot client: # mkdir -p /export/client/root Put the following line in /etc/exports to enable NFS sharing: /export/client/root -maproot=root client.test.net If your server is currently running an NFS server, you only need to restart mountd(8). Otherwise, you need to start rpcbind(8) and nfsd(8). If the server is running NetBSD, you can achieve this with: # /etc/rc.d/rpcbind start # /etc/rc.d/nfsd start # /etc/rc.d/mountd restart 5. NetBSD kernel and installation tools If you are netbooting the installer, use binary/kernel/netbsd-INSTALL_WALNUT.img.gz (this has the installation tools in a RAM disk). Also, copy the distribution files to the client's root directory. # cp *tgz /export/client/root # gunzip netbsd-INSTALL.img.gz # mv netbsd-INSTALL.img /export/client/root/netbsd If you are running your evbppc diskless, simply use binary/kernel/netbsd.img-WALNUT.gz. 6. Client file system You can skip this step if you do not plan to run your client diskless after installation. Otherwise, you need to extract and set up the client's installation of NetBSD. The Diskless HOW-TO describes how to provide better security and save space on the NFS server over the proce- dure listed here. http://www.NetBSD.org/docs/network/netboot/nfs.html o Extracting distribution sets # cd /export/client/root # tar -xpzf /path/to/files/base.tgz # tar -xpzf /path/to/files/etc.tgz Continue with the other non-essential distribution sets if desired. o Set up swap # mkdir /export/client/root/swap # dd if=/dev/zero of=/export/client/swap bs=4k count=4k # echo '/export/client/swap -maproot=root:wheel client.test.net' | cat >> /etc/exports # /etc/rc.d/mountd restart This creates a 16 MB swap file and exports it to the client. o Create device nodes # cd /export/client/root/dev # ./MAKEDEV all This procedure only works on NetBSD hosts. o Set up the client's fstab(5) Create a file in /export/client/root/etc/fstab with the following lines: server:/export/client/swap none swap sw,nfsmntpt=/swap server:/export/client/root / nfs rw 0 0 o Set up the client's rc.conf(5) Edit /export/client/root/etc/rc.conf rc_configured=YES hostname="client" defaultroute="192.168.1.1" nfs_client=YES auto_ifconfig=NO net_interfaces="" Make sure rc does not reconfigure the network device since it will lose its connection to the NFS server with your root file system. o Set up the client's hosts(5) file. Edit /export/client/root/etc/hosts ::1 localhost 127.0.0.1 localhost 192.168.1.10 client.test.net client 192.168.1.5 server.test.net server 7. Setting up the server daemons If you want these services to start up every time you boot your server, make sure the following lines are present in your /etc/rc.conf: nfs_server=YES # enable server daemons mountd=YES rpcbind=YES rpcbind_flags="-l" # -l logs libwrap Also, you'll need to make sure the tftpd line in /etc/inetd.conf remains uncommented. Installing the NetBSD System Booting the installer The kernel starts automatically once it is loaded. Example of a normal boot If you already configured the network settings, just press `0' from the boot menu to boot. Common Problems and Error Messages Do not use the plain ELF kernel as the file provided to the firmware, use the ``netbsd.img'' file (which is in the format the firmware expects). Of course, you should put the matching ``netbsd'' as /netbsd on your root file system, otherwise some kernel grovellers won't work. Running the sysinst installation program 1. Introduction Using sysinst, installing NetBSD is a relatively easy process. You still should read this document and have it in hand when doing the installation process. This document tries to be a good guideline for the installation and as such covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. Possible hardware problems Should you encounter hardware problems during installation, try rebooting after unplugging removable devices you don't need for installation. Non- removable devices can be disabled with userconf (use boot -c to enter it). 3. General The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installa- tion system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst program from the command prompt. It is not neces- sary to reboot. 4. Quick install First, let's describe a quick install. The other sections of this docu- ment go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instructions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. o What you need. - The distribution sets (in this example, they are on CD). - Some form of bootable media, described above. - A CD-ROM drive (SCSI or ATAPI), a hard disk and a minimum of of memory installed. - The hard disk should have at least + n megabytes of space free, where n is the number of megabytes of main memory in your system. If you wish to install the X Window System as well, you will need at least 120 MB more. o The Quick Installation - Boot the system as described above. You should be at the sysinst main menu. .***********************************************. * NetBSD-4.0.1 Install System * * * *>a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * x: Exit Install System * .***********************************************. - If you wish, you can configure some network settings immediately by choosing the Utility menu and then Configure network. It isn't actually required at this point, but it may be more conve- nient. Go back to the main menu. - Choose install. - You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. - After your disk has been prepared, choose CD-ROM as the medium. The default values for the path and device should be ok. - After all the files have been unpacked, go back to the main menu and select reboot, after you have removed the bootfloppy from the drive. - NetBSD will now boot. If you haven't already done so in sysinst, you should log in as root, and set a password for that account. You are also advised to edit the file /etc/rc.conf to match your system needs. - Your installation is now complete. - For configuring the X window system, if installed, see the files in /usr/X11R6/lib/X11/doc. Further information can be found on http://www.xfree86.org/. 5. Booting NetBSD You may want to read the boot messages, to notice your disk's name and capacity. Its name will be something like sd0 or wd0 and the geometry will be printed on a line that begins with its name. As mentioned above, you may need your disk's geometry when creating NetBSD's partitions. You will also need to know the name, to tell sysinst on which disk to install. The most important thing to know is that wd0 is NetBSD's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 6. Network configuration If you will not use network operation during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu, and select the Configure network option. If you only want to temporarily use networking during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response in reply to answers relating to this. 7. Installation drive selection and parameters To start the installation, select Install NetBSD to hard disk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. Depending on how many disks are found, you may get a different message. You should see disk names like sd0 or sd1. 8. Partitioning the disk o Which portion of the disk to use. You will be asked if you want to use the entire disk or only part of the disk. If you decide to use the entire disk for NetBSD, it will be checked if there are already other systems present on the disk, and you will be asked to confirm whether you want to overwrite these. 9. Editing the NetBSD disklabel The partition table of the NetBSD part of a disk is called a disklabel. There are 4 layouts for the NetBSD part of the disk that you can pick from: Standard, Standard with X, Custom and Use Existing. The first two use a set of default values (that you can change) suitable for a normal installation, possibly including X. With the Custom option you can spec- ify everything yourself. The last option uses the partition info already present on the disk. You will be presented with the current layout of the NetBSD disklabel, and given a chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap partition has a special type called swap. Some partitions in the diskla- bel have a fixed purpose. a Root partition (/) b Swap partition. c The NetBSD portion of the disk. d-p Available for other use. Traditionally, e is the partition mounted on /usr, but this is historical practice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it some- thing different, make sure the name is a single word and contains no spe- cial characters. You don't need to remember this name. 10. Preparing your hard disk You are now at the point of no return. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to proceed, enter yes at the prompt. The install program will now label your disk and make the file systems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are run- ning. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Oth- erwise, you can continue the installation program after pressing the return key. 11. Getting the distribution sets The NetBSD distribution consists of a number of sets, that come in the form of gzipped tarfiles. A few sets must be installed for a working system, others are optional. At this point of the installation, you will be presented with a menu which enables you to choose from one of the fol- lowing methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 12. Installation using ftp To be able to install using ftp, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS when answering the questions to configure net- working, you will need to specify an IP address instead of a hostname for the ftp server. sysinst will proceed to transfer all the default set files from the remote site to your hard disk. 13. Installation using NFS To be able to install using NFS, you first need to configure your network setup, if you haven't already at the start of the install procedure. sysinst will do this for you, asking you if you want to use DHCP, and if not to provide data like IP address, hostname, etc. If you do not have name service set up for the machine that you are installing on, you can just press RETURN in answer to these questions, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e. correctly exported to your machine. If you did not set up DNS when answering the questions to configure net- working, you will need to specify an IP address instead of a hostname for the NFS server. 14. Installation from CD-ROM When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM player (usually cd0), and the directory name on the CD-ROM where the distribution files are. sysinst will then check if the files are indeed available in the speci- fied location, and proceed to the actual extraction of the sets. 15. Installation from an unmounted file system In order to install from a local file system, you will need to specify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location. 16. Installation from a local directory This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file system that is already accessible. sysinst will ask you for the name of this directory. 17. Extracting the distribution sets After the install sets containing the NetBSD distribution have been made available, you can either extract all the sets (a full installation), or only extract sets that you have selected. In the latter case, you will be shown the currently selected sets, and given the opportunity to select the sets you want. Some sets always need to be installed (kern, base, and etc) they will not be shown in this selection menu. Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably, especially on machines with slow graphics consoles or serial consoles. Alternatively, you will be asked if you wish to have a progress bar. This is the pre- ferred option as it shows progress without significantly slowing down the installation process. After all the files have been extracted, all the necessary device node files will be created. If you have already configured networking, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the network configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can then set a pass- word for the "root" account, to prevent the machine coming up without access restrictions. 18. Finalizing your installation Congratulations, you have successfully installed NetBSD 4.0.1. You can now reboot the machine, and boot NetBSD from hard disk. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state, with the most important ones described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the system asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc direc- tory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi-user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). If your /usr directory is on a separate partition and you do not know how to use ed, you will have to mount your /usr partition to gain access to ex or vi. Do the following: # mount /usr # export TERM=vt220 If you have /var on a separate partition, you need to repeat that step for it. After that, you can edit /etc/rc.conf with vi(1). When you have finished, type exit at the prompt to leave the single-user shell and con- tinue with the multi-user boot. Other values that need to be set in /etc/rc.conf for a networked environ- ment are hostname and possibly defaultroute, furthermore add an ifconfig_int for your network interface, along the lines of ifconfig_de0="inet 123.45.67.89 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_de0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventurous) run named(8). See resolv.conf(5) or named(8) for more information. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. If you're using the machine in a networked environment, you should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a dif- ferent user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. Unless you have connected an unusual terminal device as the console you can just press RETURN when it prompts for Terminal type? [...]. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you have installed the X Window System, look at the files in /usr/X11R6/lib/X11/doc for information. Don't forget to add /usr/X11R6/bin to your path in your shell's dot file so that you have access to the X binaries. 5. Installing third party packages If you wish to install any of the software freely available for UNIX-like systems you are strongly advised to first check the NetBSD package sys- tem. This automatically handles any changes necessary to make the soft- ware run on NetBSD, retrieval and installation of any other packages on which the software may depend, and simplifies installation (and deinstal- lation), both from source and precompiled binaries. o More information on the package system is at http://www.NetBSD.org/docs/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc/README.html o Precompiled binaries can be found at ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/ usually in the evbppc/4.0/All subdir. You can install them with the following commands under sh(1): # PKG_PATH=ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/evbppc/4.0/All # export PKG_PATH # pkg_add -v tcsh # pkg_add -v bash # pkg_add -v perl # pkg_add -v apache # pkg_add -v kde # pkg_add -v firefox ... If you are using csh(1) then replace the first two lines with the following: # setenv PKG_PATH ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/evbppc/4.0/All ... Note: Some mirror sites don't mirror /pub/pkgsrc directory. If you would like to use such mirrors, you could also try the /pub/NetBSD/packages/current-packages/NetBSD/evbppc/4.0/All directory which may have the same contents. The above commands will install the Tenex-csh and Bourne Again shell, the Perl programming language, Apache web server, KDE desktop envi- ronment and the Firefox web browser as well as all the packages they depend on. Note: In some case the pkg_add(1) command will complain about a ver- sion mismatch of packages with a message like the following: Warning: package `foo' was built for a different version of the OS: NetBSD/i386 4.0 (pkg) vs. NetBSD/i386 4.0.1 (this host), This warning would be harmless if the formal major release numbers are same between the pkg and your host. Please refer ``the NetBSD release glossary and graphs'': http://www.NetBSD.org/releases/release-map.html for details of the release numbering scheme of NetBSD. o Package sources for compiling packages on your own can be obtained by retrieving the file ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc.tar.gz They are typically extracted into /usr/pkgsrc (though other locations work fine), with the commands: # mkdir /usr/pkgsrc # cd /usr/pkgsrc # tar -zxpf pkgsrc.tar.gz After extracting, see the README and doc/pkgsrc.txt files in the extraction directory (e.g. /usr/pkgsrc/README) for more information. 6. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/postfix/main.cf file will almost definitely need to be adjusted. If you prefer a different MTA, then install it using the NetBSD package system or by hand and adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the manual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System This is the first release of NetBSD/evbppc, and as such, there is no ability to upgrade from a prior release. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the follow- ing problems and compatibility issues in mind when upgrading to NetBSD 4.0.1. N.B. when using sysinst for upgrading, it will automatically invoke postinstall fix and thus all issues that are fixed by postinstall by default (see below) will be handled. Issues affecting an upgrade from NetBSD 2.1 and older releases. See the section below on upgrading from NetBSD 3.x as well. It is very important that you populate the directory /etc/pam.d with appropri- ate configuration files for Pluggable Authentication Modules (PAM) because you will not be able to login any more otherwise. Using postinstall as described below will take care of this. Please refer to http://www.NetBSD.org/docs/guide/en/chap-pam.html for documentation about PAM. The following issues can generally be resolved by running postinstall with the etc set : postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/pam.d/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* The following issues need to be resolved manually: o The user `_pflogd' and the groups `_pflogd' and `authpf' need to be created. Issues affecting an upgrade from NetBSD 3.x releases. The following issues can generally be resolved by running postinstall with the etc set : postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* - /etc/envsys.conf The following issues need to be resolved manually: o The users `_proxy', `_rwhod', and `_sdpd' and the groups `_proxy', `_rwhod' and `_sdpd' need to be created and the user `uucp' needs to be updated. o A number of things have been removed from the NetBSD 4.0 release including: the evbsh5 port, the Fortran 77 compiler (g77), NETCCITT, NETNS, Sendmail, Sushi, UUCP, and Vinum. If you were using any of these, then please see the "Components removed from NetBSD" section near the beginning of this document. o The replacement of Sendmail by Postfix can be handled automatically by postinstall but it is not done by default. If you want to tran- sition to Postfix, the command postinstall -s /path/to/etc.tgz fix mailerconf will update your /etc/mailer.conf file to use Postfix as the MTA. When using sysinst to upgrade the system, it will ask if you want this to be done. Note that if you have a customized Sendmail setup, you need to set up Postfix in an equivalent way; there is no tool for automatic con- version of Sendmail configuration to a Postfix one. Postfix will be started up automatically when the system boots. You may see messages like "$sendmail is not set properly" at boot. You can suppress them by removing /etc/rc.d/sendmail and /etc/rc.d/smmsp. Those files and other parts of sendmail configura- tion like files under /usr/share/sendmail are not removed by default while upgrading for those who want to continue using sendmail from outside the base system. If you want to delete them, postinstall can be used: postinstall -s /path/to/etc.tgz fix sendmail Issues with GDB 6.5 Some architectures (arm, i386, powerpc and sparc64) have switched to a newer gdb version (6.5) in this release. Unfortunately support for debugging pro- grams using the SA (scheduler activation) based thread library, is incomplete in this gdb version. Furthermore kernel crashdumps can not be debugged due to a missing identification in the kernel binaries. Both issues have been addressed on the wrstuden-fixsa branch, but did not make it into the NetBSD release. Both will be fixed in the next patch release. Using online NetBSD documentation Documentation is available if you first install the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are o intro(1), o man(1), o apropros(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the section should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after logging in, enter # man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter # apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are vari- ous mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instructions. There are various mailing lists set up to deal with comments and questions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Additionally, bug reports can be sent by mail to: netbsd-bugs@NetBSD.org. Use of send-pr(1) is encouraged, however, because bugs reported with it are entered into the NetBSD bugs database, and thus can't slip through the cracks. There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/mailinglists/. If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-users@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW some- where, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, including (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their ongoing work on BSD systems, support, and encouragement. o The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. o The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. o The Lulea Academic Computer Society for providing the backup services server. o The Columbia University Computer Science Department for hosting the NYC build cluster. o The Western Washington University Computer Science Department for running the WWU build cluster that produces daily snapshots. o The many organizations that provide NetBSD mirror sites. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o We list the individuals and organizations that have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it at http://www.NetBSD.org/donations/. (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into devel- oping NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to be mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Alistair Crooks agc@NetBSD.org Quentin Garnier cube@NetBSD.org Matt Thomas matt@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): Erik Berls cyber@NetBSD.org cobalt Manuel Bouyer bouyer@NetBSD.org xen Simon Burge simonb@NetBSD.org evbmips Simon Burge simonb@NetBSD.org pmax Simon Burge simonb@NetBSD.org sbmips Julian Coleman jdc@NetBSD.org atari Marcus Comstedt marcus@NetBSD.org dreamcast Andrew Doran ad@NetBSD.org amd64 Andrew Doran ad@NetBSD.org i386 Matthias Drochner drochner@NetBSD.org cesfic Gavan Fantom gavan@NetBSD.org iyonix Jaime A Fournier ober@NetBSD.org zaurus Matt Fredette fredette@NetBSD.org sun2 Ichiro FUKUHARA ichiro@NetBSD.org hpcarm Chris Gilbert chris@NetBSD.org cats Ben Harris bjh21@NetBSD.org acorn26 Ross Harvey ross@NetBSD.org alpha Nick Hudson skrll@NetBSD.org hp700 Martin Husemann martin@NetBSD.org sparc64 IWAMOTO Toshihiro toshii@NetBSD.org hpcarm Darrin Jewell dbj@NetBSD.org next68k Soren Jorvang soren@NetBSD.org sgimips Wayne Knowles wdk@NetBSD.org mipsco Takayoshi Kochi kochi@NetBSD.org ia64 Paul Kranenburg pk@NetBSD.org sparc Michael Lorenz macallan@NetBSD.org macppc Anders Magnusson ragge@NetBSD.org vax Cherry G. Mathew cherry@NetBSD.org ia64 NISHIMURA Takeshi nsmrtks@NetBSD.org x68k Tohru Nishimura nisimura@NetBSD.org luna68k Tohru Nishimura nisimura@NetBSD.org sandpoint Andrey Petrov petrov@NetBSD.org sparc64 Scott Reynolds scottr@NetBSD.org mac68k Tim Rightnour garbled@NetBSD.org ofppc Tim Rightnour garbled@NetBSD.org prep Tim Rightnour garbled@NetBSD.org rs6000 Noriyuki Soda soda@NetBSD.org arc Ignatios Souvatzis is@NetBSD.org amiga Jonathan Stone jonathan@NetBSD.org pmax Shin Takemura takemura@NetBSD.org hpcmips Matt Thomas matt@NetBSD.org alpha Matt Thomas matt@NetBSD.org netwinder Jason Thorpe thorpej@NetBSD.org algor Jason Thorpe thorpej@NetBSD.org evbarm Jason Thorpe thorpej@NetBSD.org shark Izumi Tsutsui tsutsui@NetBSD.org ews4800mips Izumi Tsutsui tsutsui@NetBSD.org hp300 Izumi Tsutsui tsutsui@NetBSD.org news68k Valeriy E. Ushakov uwe@NetBSD.org landisk Nathan Williams nathanw@NetBSD.org sun3 Steve Woodford scw@NetBSD.org evbppc Steve Woodford scw@NetBSD.org mvme68k Steve Woodford scw@NetBSD.org mvmeppc Reinoud Zandijk reinoud@NetBSD.org acorn32 The NetBSD 4.0.1 Release Engineering team: Grant Beattie grant@NetBSD.org Manuel Bouyer bouyer@NetBSD.org David Brownlee abs@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Havard Eidnes he@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org John Heasley heas@NetBSD.org Geert Hendrickx ghen@NetBSD.org Soren Jacobsen snj@NetBSD.org Daniel de Kok daniel@NetBSD.org Phil Nelson phil@NetBSD.org Jeff Rizzo riz@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Christoph Badura bad@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Alan Barrett apb@NetBSD.org Grant Beattie grant@NetBSD.org Jason Beegan jtb@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Mason Loring Bliss mason@NetBSD.org Charles Blundell cb@NetBSD.org Rafal Boni rafal@NetBSD.org Stephen Borrill sborrill@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org John Brezak brezak@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Frederick Bruckman fredb@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org Pavel Cahyna pavel@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Daniel Carosone dan@NetBSD.org Dave Carrel carrel@NetBSD.org James Chacon jmc@NetBSD.org Mihai Chelaru kefren@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Ben Collver ben@NetBSD.org Marcus Comstedt marcus@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Aidan Cully aidan@NetBSD.org Garrett D'Amore gdamore@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Jed Davis jld@NetBSD.org Matt DeBergalis deberg@NetBSD.org Arnaud Degroote degroote@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Havard Eidnes he@NetBSD.org Jaime A Fournier ober@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hauke Fath hauke@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt J. Fleming mjf@NetBSD.org Marty Fouts marty@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Brian Ginsbach ginsbach@NetBSD.org Paul Goyette pgoyette@NetBSD.org Michael Graff explorer@NetBSD.org Brian C. Grayson bgrayson@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Ulrich Habel rhaen@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org Adam Hamsik haad@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Ben Harris bjh21@NetBSD.org Ross Harvey ross@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org HAYAKAWA Koichi haya@NetBSD.org John Heasley heas@NetBSD.org Geert Hendrickx ghen@NetBSD.org Rene Hexel rh@NetBSD.org Iain Hibbert plunky@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Adam Hoka ahoka@NetBSD.org Jachym Holecek freza@NetBSD.org David A. Holland dholland@NetBSD.org Christian E. Hopps chopps@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hornquist Astrand lha@NetBSD.org Roland Illig rillig@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Nicolas Joly njoly@NetBSD.org Chris Jones cjones@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Masanori Kanaoka kanaoka@NetBSD.org Antti Kantee pooka@NetBSD.org Frank Kardel kardel@NetBSD.org Mattias Karlsson keihan@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Mario Kemper magick@NetBSD.org Min Sik Kim minskim@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org John Kohl jtk@NetBSD.org Daniel de Kok daniel@NetBSD.org Jonathan A. Kollasch jakllsch@NetBSD.org Paul Kranenburg pk@NetBSD.org Lubomir Kundrak lkundrak@NetBSD.org Jochen Kunz jkunz@NetBSD.org Martti Kuparinen martti@NetBSD.org Kentaro A. Kurahone kurahone@NetBSD.org Arnaud Lacombe alc@NetBSD.org Kevin Lahey kml@NetBSD.org David Laight dsl@NetBSD.org Johnny C. Lam jlam@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Tonnerre Lombard tonnerre@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org Paul Mackerras paulus@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org Anders Magnusson ragge@NetBSD.org Cherry G. Mathew cherry@NetBSD.org David Maxwell david@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Perry Metzger perry@NetBSD.org Luke Mewburn lukem@NetBSD.org Brook Milligan brook@NetBSD.org Minoura Makoto minoura@NetBSD.org Simas Mockevicius symka@NetBSD.org der Mouse mouse@NetBSD.org Joseph Myers jsm@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Phil Nelson phil@NetBSD.org John Nemeth jnemeth@NetBSD.org Bob Nestor rnestor@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Tobias Nygren tnn@NetBSD.org OBATA Akio obache@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Rui Paulo rpaulo@NetBSD.org Jonathan Perkin sketch@NetBSD.org Andrey Petrov petrov@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Peter Postma peter@NetBSD.org Dante Profeta dante@NetBSD.org Chris Provenzano proven@NetBSD.org Niels Provos provos@NetBSD.org Mindaugas Rasiukevicius rmind@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Michael Richardson mcr@NetBSD.org Tim Rightnour garbled@NetBSD.org Alan Ritter rittera@NetBSD.org Jeff Rizzo riz@NetBSD.org Hans Rosenfeld hans@NetBSD.org Gordon Ross gwr@NetBSD.org Steve Rumble rumble@NetBSD.org Ilpo Ruotsalainen lonewolf@NetBSD.org Heiko W. Rupp hwr@NetBSD.org Blair J. Sadewitz bjs@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Silke Scheler silke@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Takeshi Shibagaki shiba@NetBSD.org Naoto Shimazaki igy@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Daniel Sieger dsieger@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org SOMEYA Yoshihiko someya@NetBSD.org Bill Sommerfeld sommerfeld@NetBSD.org Jorg Sonnenberger joerg@NetBSD.org Ignatios Souvatzis is@NetBSD.org T K Spindler dogcow@NetBSD.org Bill Squier groo@NetBSD.org Jonathan Stone jonathan@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org SUNAGAWA Keiki kei@NetBSD.org Kimmo Suominen kim@NetBSD.org Robert Swindells rjs@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Ian Lance Taylor ian@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Todd Whitesel toddpw@NetBSD.org Frank Wille phx@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Dan Winship danw@NetBSD.org Jim Wise jwise@NetBSD.org Michael Wolfson mbw@NetBSD.org Colin Wood ender@NetBSD.org Steve Woodford scw@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org David Young dyoung@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Maria Zevenhoven maria7@NetBSD.org Christos Zoulas christos@NetBSD.org Other contributors: Dave Burgess burgess@cynjut.infonet.net Brian R. Gaeke brg@dgate.org Brad Grantham grantham@tenon.com Lawrence Kesteloot kesteloo@cs.unc.edu Waldi Ravens waldi@moacs.indiv.nl.net Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trademarks of their respective owners. The following notices are required to satisfy the license terms of the soft- ware that we have mentioned in this document: NetBSD is a registered trademark of The NetBSD Foundation, Inc. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product contains software developed by Ignatios Souvatzis for the NetBSD project. This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project. This product contains software written by Michael L. Hitch for the NetBSD project. This product includes cryptographic software written by Eric Young (eay@crypt- soft.com) This product includes cryptographic software written by Eric Young (eay@min- com.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Divi- sion, US Naval Research Laboratory. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Gordon W. Ross and Leo Weppelman. This product includes software developed by Hellmuth Michaelis and Joerg Wun- sch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Univer- sity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Alistair G. Crooks. This product includes software developed by Alistair G. Crooks. for the NetBSD project. This product includes software developed by Allen Briggs This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, sub- stitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brad Pepers This product includes software developed by Bradley A. Grantham. This product includes software developed by Brini. This product includes software developed by Causality Limited. This product includes software developed by Charles D. Cranor and Seth Widoff. This product includes software developed by Charles D. Cranor and Washington University. This product includes software developed by Charles D. Cranor, Washington Uni- versity, and the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor, Washington Uni- versity, the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the Univer- sity of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christian Limpach This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Cybernet Corporation and Nan Yang Computer Services Limited This product includes software developed by Daishi Kato This product includes software developed by Dale Rahn. This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Darrin B. Jewell This product includes software developed by David Miller. This product includes software developed by Dean Huxley. This product includes software developed by Eduardo Horvath. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@mincom.oz.au) This product includes software developed by Eric Young (eay@cryptsoft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by Ezra Story and by Kari Mettinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Gordon W. Ross This product includes software developed by HAYAKAWA Koichi. This product includes software developed by Harvard University and its con- tributors. This product includes software developed by Harvard University. This product includes software developed by Herb Peyerl. This product includes software developed by Hubert Feyrer for the NetBSD Project. This product includes software developed by Iain Hibbert This product includes software developed by Ian F. Darwin and others. This product includes software developed by Ian W. Dall. This product includes software developed by Ichiro FUKUHARA. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jared D. McNeill. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Communica- tions, http://www.and.com/ This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Juan Romero Pardines for the NetBSD Foundation, Inc. and its contributors. This product includes software developed by Jukka Marin. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berkeley and its con- tributors. This product includes software developed by LAN Media Corporation and its con- tributors. This product includes software developed by Leo Weppelman for the NetBSD Project. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Luke Mewburn. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Manuel Bouyer. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Murray This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Martin Husemann and Wolfgang Sol- frank. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Mats O Jansson and Charles D. Cra- nor. This product includes software developed by Mats O Jansson. This product includes software developed by Matt DeBergalis This product includes software developed by Matthew Fredette. This product includes software developed by Matthias Pfaller. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Michael Graff. This product includes software developed by Michael L. Hitch. This product includes software developed by Michael Shalayeff. This product includes software developed by Michael Smith. This product includes software developed by Mike Glover and contributors. This product includes software developed by Mike Pritchard. This product includes software developed by Minoura Makoto. This product includes software developed by Nan Yang Computer Services Lim- ited. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Onno van der Linden. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by Philip L. Budne. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Roland C. Dowdeswell. This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Soren S. Jorvang. This product includes software developed by Stephan Thesing. This product includes software developed by Steve Woodford. This product includes software developed by Takashi Hamada This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by Tetsuya Isaki. This product includes software developed by Thomas Gerner This product includes software developed by Thomas Klausner for the NetBSD Project. This product includes software developed by Tobias Weingartner. This product includes software developed by Todd C. Miller. This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project. This product includes software developed by Tohru Nishimura for the NetBSD Project. This product includes software developed by Tohru Nishimura. for the NetBSD Project. This product includes software developed by TooLs GmbH. This product includes software developed by Toru Nishimura. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contributors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Science at the University of Utah. This product includes software developed by the Charles D. Cranor, Washington University, University of California, Berkeley and its contributors. This product includes software developed by the Computer Systems Engineering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Kungliga Tekniska Hogskolan and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) This product includes software developed by the PocketBSD project and its con- tributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Development Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia University. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Christos Zoulas This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Ignatios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Michael L. Hitch. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bar- tram and Frank van der Linden This product includes software developed for the NetBSD Project by Allegro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Piermont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Sys- tems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsy- con AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, Tele- Muse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Laboratory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Marshall M. Midden. This product includes software developed or owned by Caldera International, Inc. The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation. In the following statement, the phrase ``this text'' refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in NetBSD, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html. This notice shall appear on any product containing this material This product includes software developed by Brini. This product includes software developed by Mark Brinicombe for the NetBSD Project. This product includes software developed by Mark Brinicombe. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Charles M. Hannum. This product includes software developed by the NetBSD Foundation, Inc. and its contributors. This product includes software developed by TooLs GmbH. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed for the NetBSD Project by Wasabi Sys- tems, Inc. The End NetBSD October 5, 2008 NetBSD