INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL -- Installation procedure for NetBSD/alpha. CONTENTS About this Document............................................2 What is NetBSD?................................................2 Security Advisory Fixes.....................................3 Other Security Fixes........................................4 Kernel......................................................4 File Systems................................................4 Networking..................................................4 Miscellaneous Drivers.......................................5 Audio.......................................................5 Storage.....................................................5 Platform specific...........................................5 Miscellaneous...............................................6 Features to be removed in a later release......................7 The NetBSD Foundation..........................................7 Sources of NetBSD..............................................7 NetBSD 5.2 Release Contents....................................7 NetBSD/alpha subdirectory structure.........................8 Bootable installation/upgrade floppies......................9 Binary distribution sets....................................9 NetBSD/alpha System Requirements and Supported Devices........11 Supported PCI bus devices..................................11 Supported ISA bus devices..................................12 Supported EISA bus devices.................................12 Supported Turbochannel bus devices.........................12 Getting the NetBSD System on to Useful Media..................13 Preparing your System for NetBSD installation.................15 Installing the NetBSD System..................................15 Running the sysinst installation program...................19 Introduction............................................19 Possible hardware problems..............................19 General.................................................19 Quick install...........................................19 Booting NetBSD..........................................20 Network configuration...................................20 Installation drive selection and parameters.............21 Selecting which sets to install.........................21 Partitioning the disk...................................21 Preparing your hard disk................................21 Getting the distribution sets...........................22 Installation from CD-ROM................................22 Installation using ftp..................................22 Installation using NFS..................................22 Installation from an unmounted file system..............23 Installation from a local directory.....................23 Extracting the distribution sets........................23 Finalizing your installation............................23 Post installation steps.......................................23 Upgrading a previously-installed NetBSD System................26 Compatibility Issues With Previous NetBSD Releases............26 Issues when running older binaries on NetBSD 5.2...........27 Issues affecting an upgrade from NetBSD 3.x releases.......27 Issues affecting an upgrade from NetBSD 4.x releases.......28 Using online NetBSD documentation.............................29 Administrivia.................................................30 Thanks go to..................................................30 We are........................................................31 Legal Mumbo-Jumbo.............................................37 The End.......................................................43 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 5.2 on the alpha platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX-like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on 57 different system architectures (ports) across 15 distinct CPU families, and is being ported to more. The NetBSD 5.2 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distribution. Please see the NetBSD web site at http://www.NetBSD.org/ for information on them.) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. The complete list of changes can be found in the CHANGES-5.2: http://ftp.NetBSD.org/pub/NetBSD/NetBSD-5.2/CHANGES-5.2 file in the top level directory of the NetBSD 5.2 release tree. An abbre- viated list is as follows: Security Advisory Fixes o NetBSD-SA2010-012: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2010-012.txt.asc OpenSSL TLS extension parsing race condition o NetBSD-SA2011-001: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-001.txt.asc BIND DoS due to improper handling of RRSIG records o NetBSD-SA2011-002: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-002.txt.asc OpenSSL TLS extension parsing race condition o NetBSD-SA2011-003: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-003.txt.asc Exhausting kernel memory from user controlled value o NetBSD-SA2011-004: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-004.txt.asc Kernel stack overflow via nested IPCOMP packet (CVE-2011-1547) o NetBSD-SA2011-005: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-005.txt.asc ISC dhclient does not strip shell meta-characters (CVE-2011-0997) o NetBSD-SA2011-006: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-006.txt.asc BIND DoS via packet with rrtype zero o NetBSD-SA2011-007: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-007.txt.asc LZW decoding loop on manipulated compressed files o NetBSD-SA2011-008: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-008.txt.asc OpenPAM privilege escalation (CVE-2010-1166) o NetBSD-SA2011-009: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2011-009.txt.asc BIND resolver DoS o NetBSD-SA2012-001: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2012-001.txt.asc OpenSSL buffer overflow in DER read function o NetBSD-SA2012-002: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2012-002.txt.asc OpenSSL Invalid TLS/DTLS record attack o NetBSD-SA2012-003: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2012-003.txt.asc Intel processors sysret to non-canonical address behaviour o NetBSD-SA2012-004: ,: http://ftp.NetBSD.org/pub/NetBSD/security/advisories/NetBSD-SA2012-004.txt.asc BIND resolver DoS when using DNSSEC Validation Advisories prior to NetBSD-SA2010-012 do not affect NetBSD 5.2: .: http://www.NetBSD.org/support/security/patches-5.2.html Other Security Fixes o openssl: Fix CVE-2010-3864, CVE-2010-4180, CVE-2011-0014, CVE-2011-4109, CVE-2011-4576, CVE-2012-0050, CVE-2012-2110, and CVE-2012-2333. o postfix: Fix CVE-2011-0411 and CVE-2011-1720. o xrdb: Fix CVE-2011-0465. o dhcpcd(8): Fix CVE-2011-996. o BIND: Fix CVE-2011-1910, CVE-2011-0414, CVE-2011-2464, CVE-2011-4313, CVE-2012-3817, CVE-2012-4244, and CVE-2012-5166. o Address CVE-2011-2895, buffer overflow in decompression, affecting multiple system utilities. o bpf(4): avoid stack memory disclosure. Kernel o Fix ptrace(2) PT_SYSCALL. File Systems o WAPBL: Fix an error that could lead to file system corruption and "freeing free block" panics. o ext2fs: support inodes > 128 bytes, variable inode sizes, and 32 bit UID fields. o fss(4): various fixes for snapshots. o Numerous fixes for extended attributes on UFS1 file systems. o Fix rename locking for UFS. Networking o wm(4): add support for more chips, work around some other issues. o bge(4): add support for many more chips, and many bugfixes. o ne(4): add NE2000 with 8bit bus width support, and EtherNEC support. o Fix NULL pointer dereferences in IPv6 ESP code paths. o Make EtherIP in IPv6 input path work. o Fix MPPE in pppd. o Clean up setting ECN bit in TOS. o Added SOCK_SEQPACKET to PL_LOCAL sockets. o Prevent a crash when destroying an interface. Miscellaneous Drivers o btmagic(4): add Apple Magic Mouse driver. o rnd(4): prevent crash if len field in ioctl(RNDADDDATA) is garbage. o uts(4): driver for USB touchscreens. Audio o hdaudio(4): - Add support for NVidia controllers. - Fix 32KHz playback. PR#43542. Storage o esiop(4) / siop(4): Improve error paths. PR#43278. o aac(4): support more boards. o dk(4): avoid a LOCKDEBUG panic on raid(4). o ciss(4): Fix a performance problem. Also fix a DIAGNOSTIC panic. o Fix an issue with >2TB disks. o - raid(4): - Add support for >2TB raid devices. - Add support for non-512-byte sector disks (up to 16KB). - Add a hack to fix up disks with very old raidframe component labels. o mpt(4): Add byte-swapping so this works on bigendian platforms. Allow mpt(4) to use tagged queueing on SAS adapters. o vnd(4): fix using sparse files as backing store. o raid(4): parity maps always have at least one parity region. Platform specific o x86 (amd64 and i386) - Fix an array overflow when cpuid >= 32. - Xorg: add more support for Intel HD3000/4000 and some for HD5000. - Various fixes to allow NetBSD to run unmodified under Linux KVM. o amiga - Raise address of user stack to highest safe address, which increases available user address space by 256MB. o atari - Add support for the SMC Elite Ultra Ethernet. - Allow users to change serial console behavior with binpatch(8). - Fixes for scheduling callback functions. o dreamcast: Add workaround to make audio work. o hp300: Make install.md probe cd(4) devices properly. o hpcmips: Fix pcic kthread creation timing. PRs 41791 and 41164. o m68k: - Ensure functions like mmap(2), mremap(2), shmat(2) or sbrk(2) return -1 in case of an error. A side benefit of this is to fix a segfault caused by jemalloc when mmap(2) failed. - Fix some bad results in FPE. o macppc: pbms(4): Avoid an immediate crash during attach, and fix the aspect ratio of the trackpad on the geyser2 model. o pmax: Make ksyms(4) actually work. o sh3: Fix logic error in copyinstr() when deciding whether to return EFAULT or ENAMETOOLONG. o sparc - Many fixes for sparc SMP. o vax - Corrected the definition of leap year for vax. o x68k: - Fix boot problem on X68030+060turbo in 060 mode. - Fix panics on heavy key strokes while running X. o xen - Fix xennet hotplug and implement feature-rx-copy, improving sup- port under Linux Dom0. - xbdback: prevent dom0 pool corruption. - Fix xenbus probe so NetBSD DomU can boot on Linux Dom0 with xl. - Fix random kernel panics on domains with large memory. - Expose Xen kernfs entries inside a domU to make it possible to use xentools inside a domU to query XenStore entries. Miscellaneous o passwd(1): Log successful and unsuccessful attempts to change pass- words, via -l or PAM. o ftp(1): - Avoid NULL dereference in log output. - Parse HTTP 'Date' entries in the 'C' locale rather than the user's. o Improve 'boot -z' support. o Update to libfetch 2.31. o top(1): improve the default display for large numbers of CPUs. o Updated 32/64-bit compat to version 2. o Stop nfsd(8) from exiting prematurely during port-scan. o resize_ffs(8): support growing and shrinking all FFSv1 and growing all FFSv2 file systems. Features to be removed in a later release The following features are to be removed from NetBSD in the future: o Support for soft dependencies, also knows as soft updates (see ``softdep'' in mount(8)) will be removed in the next major release. NetBSD 5.2 includes a preview of WAPBL (Write Ahead Physical Block Logging), which will replace soft dependencies in the next major release. See wapbl(4) and http://mail-index.netbsd.org/netbsd-announce/2008/12/14/msg000051.html for details. o Support for Xen 2.0.x. The Xen-3 and hypervisor interface is diverg- ing from Xen-2 as development is ongoing, increasing the maintenance cost for NetBSD. It should be considered as deprecated. Users are expected to not rely on it any more beyond this major release. Further, at least version 3.1 of Xen will be required to run NetBSD as Dom0 or DomU. The NetBSD Foundation The NetBSD Foundation is a tax exempt, not-for-profit 501(c)(3) corpora- tion that devotes itself to the traditional goals and Spirit of the NetBSD Project and owns the trademark of the word ``NetBSD''. It sup- ports the design, development, and adoption of NetBSD worldwide. More information on the NetBSD Foundation, its composition, aims, and work can be found at: http://www.NetBSD.org/foundation/ Sources of NetBSD Refer to http://www.NetBSD.org/mirrors/ NetBSD 5.2 Release Contents The root directory of the NetBSD 5.2 release is organized as follows: .../NetBSD-5.2/ CHANGES Changes between the 4.0 and 5.0 releases. CHANGES-5.0 Changes between the initial 5.0 branch and final release of 5.0. CHANGES-5.1 Changes between the 5.0 and 5.1 releases. CHANGES-5.2 Changes between the 5.1 and 5.2 releases. CHANGES.prev Changes in previous NetBSD releases. LAST_MINUTE Last minute changes and notes about the release. README.files README describing the distribution's contents. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 5.2 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. 79 MB gzipped, 450 MB uncompressed sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. 7 MB gzipped, 32 MB uncompressed src This set contains all of the base NetBSD 5.2 sources which are not in gnusrc, sharesrc, or syssrc. 59 MB gzipped, 350 MB uncompressed syssrc This set contains the sources to the NetBSD 5.2 kernel for all architectures as well as the config(1) utility. 34 MB gzipped, 197 MB uncompressed xsrc This set contains the sources to the X Window System. 127 MB gzipped, 694 MB uncompressed All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # cd / ; tar -zxpf set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: MD5 MD5 digests in the format produced by the command: cksum -a MD5 file. SHA512 SHA512 digests in the format produced by the command: cksum -a SHA512 file. The SHA512 digest is safer, but MD5 checksums are provided so that a wider range of operating systems can check the integrity of the release files. NetBSD/alpha subdirectory structure The alpha-specific portion of the NetBSD 5.2 release is found in the alpha subdirectory of the distribution: .../NetBSD-5.2/alpha/. It con- tains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-GENERIC.gz A gzipped NetBSD kernel containing code for everything supported in this release. netbsd-GENERIC.MP.gz A gzipped NetBSD kernel containing code for everything supported in this release. This kernel supports SMP on systems with more than one CPU. sets/ alpha binary distribution sets; see below. installation/ floppy/ alpha boot and installation floppies; see below. diskimage/ an image file cdhdtape is included for the case where the installer is written to a CD, hard drive, or tape. This image file is the same for the CD, HD, and tape cases. instkernel/ contains a netbsd.gz installation kernel; this is the same installer kernel as in all the other install images, but without the various boot program and file system wrappers. It can be netbooted or diskbooted from a previous instal- lation. no need to gunzip this image. Bootable installation/upgrade floppies There are three bootable images in the NetBSD alpha distribution. One is for a floppy boot and is split into three separate files. The other is a single-file image containing the same install kernel, but intended to be written to a CD, tape, or hard drive. The third image is a GENERIC ker- nel intended for production use in unusual cases. This can be useful at some sites when: o You want to run diskless but SRM bugs prevent the firmware from net- booting. You can work around this problem by always booting the generic kernel from the floppy. o SRM doesn't recognize your (hard) disk controller but NetBSD does. This happens more frequently than you might think. SRM will usually only boot from siop(4) or isp(4) SCSI devices, and on most platforms will not boot from an IDE drive. NetBSD will happily operate with almost any SCSI root or an IDE root; the solution here is to netboot a kernel or always boot from floppy. Binary distribution sets The NetBSD alpha binary distribution sets contain the binaries which com- prise the NetBSD 5.2 release for alpha. The binary distribution sets can be found in the alpha/binary/sets subdirectory of the NetBSD 5.2 distri- bution tree, and are as follows: base The NetBSD 5.2 alpha base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be minimally func- tional. 33 MB gzipped, 103 MB uncompressed comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. 50 MB gzipped, 207 MB uncompressed etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. 1 MB gzipped, 1 MB uncompressed games This set includes the games and their manual pages. 4 MB gzipped, 9 MB uncompressed kern-GENERIC This set contains a NetBSD/alpha 5.2 GENERIC kernel, named /netbsd. You must install this distribution set. 5 MB gzipped, 10 MB uncompressed man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. 12 MB gzipped, 50 MB uncompressed misc This set includes the system dictionaries, the typesettable doc- ument set, and other files from /usr/share. 4 MB gzipped, 13 MB uncompressed text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. 4 MB gzipped, 12 MB uncompressed NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86 4.5.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. 8 MB gzipped, 25 MB uncompressed xcomp The extra libraries and include files needed to compile X source code. 16 MB gzipped, 70 MB uncompressed xfont Fonts needed by the X server and by X clients. 31 MB gzipped, 39 MB uncompressed xetc Configuration files for X which could be locally modified. 1 MB gzipped, 1 MB uncompressed xserver The X server. 8 MB gzipped, 19 MB uncompressed The alpha binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xzpf command from the root directory ( / ) of your system. Note: Each directory in the alpha binary distribution also has its own checksum files, just as the source distribution does. NetBSD/alpha System Requirements and Supported Devices NetBSD/alpha 5.2 runs on most of the DEC Alpha PCI platforms, on all of the TURBOChannel models, on the high end 8200 and 8400 systems, and on the 4100 series. The SRM console is required. This console can be distinguished from the ARC console (which is used to boot Windows NT) by the fact that it has a command line interface, rather than a menu-driven interface. The SRM prompt is `>>>'. Some platforms have both the SRM console and the ARC console, and can switch between them, and other platforms have only one type of console loaded at any one time. If your system comes up with the ARC firmware, it may be possible to switch it to SRM with a menu or to download SRM from ftp://gatekeeper.dec.com/pub/Digital/Alpha/firmware/index.html You may want to buy a firmware update CD from Compaq Computer Corpora- tion. More information on supported platforms and devices can be found on the alpha port web pages at http://www.NetBSD.org/ A basic system will fit on a 200 MB disk (including swap) without too much difficulty, but you will probably want at least 500 MB of disk to have any level of comfort. Although it is actually possible to boot and install NetBSD/alpha in only 16 MB of RAM, you will want to have at least 32 MB. We support add-in devices on the PCI, ISA, EISA and TurboChannel buses. Because NetBSD has an extremely machine-independent device driver system, many device driv- ers are the same as used in other ports that use the same bus. For exam- ple, the de network card driver is shared by the i386 and alpha ports. Some drivers on inspection appear as if they will work on the alpha but have not been tested because that hardware was not available to NetBSD testers; these are marked as UNTESTED below. If you have one of these devices, and it does work, please get in touch with port-alpha-maintainer@NetBSD.org and let us know that it works. If it doesn't work, do the same thing and we can probably fix it pretty easily. Supported PCI bus devices o Graphics Adapters - VGA-compatible video (pcivga) - ZLXp-E1 DECchip 21030-based video (tga) - ZLXp-E2 and ZLXp-E3 video (tga) o Network Cards - DECchip 21x40-family 10 and 100 Mbps Ethernet (de, tlp) - DEC DEFPA FDDI (fpa) - PCI LANCE Ethernet (le; UNTESTED) - Efficient Networks ENI-155p ATM (en; UNTESTED) - 3Com 3c59x and 3c90x (except 3c906) 10 and 100 Mbps Ether- net (ep) - Intel EtherExpress Pro 10/100B PCI Ethernet (fxp) - SMC EPIC/100 Fast Ethernet boards (epic) o SCSI Controllers - Adaptec 291x, 2920, 2930C, 294x, 295x, 39xx, 19160, 29160 and AIC-78xx SCSI (ahc) - BusLogic 9xx SCSI (bha, Works on alpha PC164) - Qlogic ISP 10x0-family SCSI (isp) - NCR/Symbios 53c8xx-family SCSI (siop, esiop; NCR825 Doesn't always work) o Miscellaneous Devices - Cyclades Cyclom-Y serial boards (cy; UNTESTED) - PCI-PCI bridges (ppb; Tested with the DECchip 21050, but should work with all bridges and system firmware revisions that comply with the PCI-PCI bridge specification) Supported ISA bus devices o Graphics Adapters - VGA-compatible video (vga; Text console only) o Network Cards - 3Com 3c509 Ethernet (ep) - DEC DE200,DE201,DE202 (le) - DEC DE203,DE204,DE205 (lc) o Miscellaneous Devices - PC-style parallel ports (lpt) - NS16450 and NS16550 UARTs (com) - ISA multi-port 16x50 boards (ast, boca; Only the latter has been tested) Supported EISA bus devices o Network Cards - DEC DEFEA FDDI (fea) - 3Com 3c5xx series (ed; UNTESTED) o SCSI Controllers - Adaptec 274x and aic7770 SCSI (ahc; UNTESTED) - BusLogic 7xx SCSI (bha; UNTESTED) Supported Turbochannel bus devices o Graphics Adapters - CFB video (PMAG-BA, cfb) - SFB video (PMAGB-BA, sfb) Note: Although these boards are supported by NetBSD/alpha since there is no keyboard or mouse support available for the TurboChannel systems, they aren't very useful. o Network Cards - DEC LANCE Ethernet (PMAD-AA, le; UNTESTED) - DEC DEFTA FDDI (PMAF-F, fta) Note that some devices, especially ISA-based devices, have to have cer- tain settings set properly for the install and GENERIC kernels to detect them. (Once installed, you can always rebuild your own kernel to detect them anywhere you wish, of course.) Here is a list of such devices and the necessary settings: Device Name Port IRQ DRQ Misc ------ ---- ---- --- --- ---- Serial ports com0 0x3f8 4 [8250/16450/16550/clones] com1 0x2f8 3 [8250/16450/16550/clones] com2 0x3e8 5 [8250/16450/16550/clones] Parallel ports lpt0 0x378 7 [interrupt-driven or polling] lpt1 0x278 [polling only] lpt2 0x3bc [polling only] AHA-174x SCSI host adapters (in enhanced mode) ahb0 any any any AHA-2X4X or AIC-7xxx-based SCSI host adapters ahc0 any any any Bus Logic BT445, BT74x, or BT9xx SCSI host adapters bha0 0x330 any any bha1 0x334 any any MFM/ESDI/IDE/RLL hard disk controllers wdc0 0x1f0 14 [supports two devices] wdc1 0x170 15 [supports two devices] ATA disks wd0, wd1, ... SCSI disks sd0, sd1, ... SCSI tapes st0, st1, ... SCSI and ATAPI CD-ROMs cd0, cd1, ... For each SCSI and IDE controller found, the SCSI or ATA(PI) devices present on the bus are probed in increasing ID order for SCSI and master/slave order for ATA(PI). So the first SCSI drive found will be called sd0, the second sd1, and so on ... 3COM 3x59X or 3COM 3x90X PCI Ethernet boards ep0 any any [you must assign an interrupt in your PCI BIOS, or let it do so for you] Intel EtherExpress 100 Fast Ethernet adapters fxp0 any any [you must assign an interrupt in your PCI BIOS, or let it do so for you] DEC DE200,201,202 EtherWORKS II/Turbo ISA Ethernet boards le? 0x300 5 memory at D0000-DFFFF le? 0x200 10 memory at D8000-DFFFF You should enter the following SRM console command to enable the le device: >>> isacfg -mk -slot ? -dev 0 -handle DE200-LE -irq0 5 -membase0 d0000 -memlen0 10000 -iobase0 300 -etyp 1 -enadev 1 DEC DE203,204,205 EtherWORKS III ISA Ethernet boards lc0 0x300 any lc1 0x320 any You should enter the following SRM console command to enable the device: >>> add_de205 Getting the NetBSD System on to Useful Media Note that if you are installing or upgrading from writable media, it can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted. Installation is supported from several media types, including: o CD-ROM / DVD o MS-DOS floppy o FTP o Remote NFS partition o Tape o Existing NetBSD partitions, if performing an upgrade The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the var- ious media are outlined below. CD-ROM / DVD Find out where the distribution set files are on the CD- ROM or DVD. Likely locations are binary/sets and alpha/binary/sets. Proceed to the instructions on installation. MS-DOS floppy NetBSD does not include split distribution sets for installation by floppy. However, they can be created on a separate machine using the split(1) command, running e.g. split -b 235k base.tgz base. to split the base.tgz file from alpha/binary/sets into files named base.aa, base.ab, and so on. Repeat this for all set_name.tgz files, split- ting them into set_name.xx files. Count the number of set_name.xx files that make up the distribution sets you want to install or upgrade. You will need one sixth that number of 1.44 MB floppies. Format all of the floppies with MS-DOS. Do not make any of them bootable MS-DOS floppies, i.e. don't use format /s to format them. (If the floppies are bootable, then the MS-DOS system files that make them bootable will take up some space, and you won't be able to fit the distribution set parts on the disks.) If you're using floppies that are formatted for MS-DOS by their manufacturers, they probably aren't bootable, and you can use them out of the box. Place all of the set_name.xx files on the MS-DOS disks. Once you have the files on MS-DOS disks, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the sec- tion on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. FTP The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. If you don't have access to a functioning nameserver during installation, the IPv4 address of ftp.NetBSD.org is 204.152.190.15 and the IPv6 address is 2001:4f8:3:7:230:48ff:fec6:9aaa:21 (as of May, 2010). Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. NFS Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the /etc/exports file on the NFS server and resetting its mount daemon (mountd). (Both of these actions will proba- bly require superuser privileges on the server.) You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once the NFS server is set up properly and you have the information mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on pre- paring your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Tape To install NetBSD from a tape, you need to make a tape that contains the distribution set files, in `tar' format. If you're making the tape on a UNIX-like system, the easi- est way to do so is probably something like: # tar -cf tape_device dist_directories where tape_device is the name of the tape device that describes the tape drive you're using; possibly /dev/rst0, or something similar, but it will vary from system to sys- tem. (If you can't figure it out, ask your system admin- istrator.) In the above example, dist_directories are the distribution sets' directories, for the distribution sets you wish to place on the tape. For instance, to put the kern-GENERIC, base, and etc distributions on tape (in order to do the absolute minimum installation to a new disk), you would do the following: # cd .../NetBSD-5.2 # cd alpha/binary # tar -cf tape_device kern-GENERIC base etc Note: You still need to fill in tape_device in the example. Once you have the files on the tape, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Preparing your System for NetBSD installation If you have any data on your disks that you want to keep, back it up before starting. Note that NetBSD/alpha does not support booting more than one operating system from a single disk, although it's fine to have multiple operating systems on your machine if you have a separate disk for NetBSD, or if one of them uses a network boot. Installing the NetBSD System To install or upgrade NetBSD, you need to first boot an installation pro- gram and then interact with the menu-based program sysinst. The instal- lation program actually consists of the NetBSD kernel plus an in-memory file system of utility programs. The traditional procedure is to write the installation system to a floppy disk set and then boot from the floppies. However, there are six ways to boot the NetBSD/alpha installation system. Each approach loads the exact same installation bits. The six paths are: o Floppy disk boot o CD boot o Hard Drive Boot o Magnetic Tape Boot o Existing Root FS Boot o Network boot In all cases, you need to transfer a bootable image of the installation system from the NetBSD CD or from an ftp site to the chosen media type. Although booting from floppy is the usual path, the hard drive boot is useful if you have another operating system (and a spare drive) already installed, or if you don't mind swapping hard drives from box to box. CD and tape boots are nice and fast if you have a CD writer or a tape format in common with another previously installed UNIX-like system. Finally, most versions of SRM can locate the NetBSD boot program netboot via bootp and download it via tftp. netboot then mounts the root file system (/) via NFS and loads the kernel. Note that if you are installing or upgrading from a writable media, the media can be write-protected if you wish. These systems mount a root image from inside the kernel, and will not need to write to the media. If you booted from a floppy, the floppy disk may be removed from the drive after the system has booted. o Floppy disk boot The 3.5", 1.44 MB boot floppy set is found under the NetBSD/alpha 5.2 distribution directory in alpha/installation/floppy/ as three files called disk1of3, disk2of3, and disk3of3. You need to put these disk images on three floppy disks. If you have a UNIX-like system handy, you can do this with commands like the following: # dd if=disk1of3 of=/dev/rfd0a bs=18k # dd if=disk2of3 of=/dev/rfd0a bs=18k # dd if=disk3of3 of=/dev/rfd0a bs=18k If the UNIX-like system you are using is not a NetBSD system, you will probably need to replace /dev/rfd0a with the name of the floppy device on your particular system. If you have an MS-DOS or Windows system available, you can use the rawrite.exe utility to transfer the image to a floppy disk. This utility is provided with the NetBSD/i386 install tools, under i386/installation/misc; a documentation file, rawrite.doc is avail- able there as well. Once the floppy has been made, you simply need to put it in the drive and type >>> B DVA0 o CD boot o Hard Drive boot o Magnetic Tape Boot All three of these media types use the same initial image: .../installation/diskimage/cdhdtape The image can be written to a hard drive partition with a command like: # dd if=cdhdtape of=/dev/rsd0c bs=16k To boot from a magnetic tape device such as DAT or DLT, it is impor- tant to create the tape image with 512-byte records. Use a command like: # dd if=cdhdtape of=/dev/rst0 bs=512 conv=osync If the host system is not NetBSD, the names of the destination devices are likely to be different. Be sure to use a ``raw partition'' device that doesn't skip over labels! The use of CD-R devices varies greatly depending on the host OS and host software; it isn't possible to give typical instructions here. o Existing Root FS Boot The installation subdirectory instkernel/ contains netbsd.gz; this is the same install kernel but without a bootable file system image wrapped around it. You can perform an complete reinstall by begin- ning it as an upgrade, and booting this kernel in the normal way off the root file system (/) of a previous installation. The gzipped image can be booted directly; it is not necessary to uncompress it first. o Network Boot Booting NetBSD/alpha 5.2 over a network requires a BOOTP or DHCP server, a TFTP server and an NFS server. (These are usually all run on the same machine.) There are three basic stages to the boot: - alpha console software sends a BOOTP request to get its own address, the address of the TFTP server and the file to download. It downloads this file, which is the second stage bootstrap, via TFTP and then executes it. - The secondary boot program resends the BOOTP request, this time also locating the NFS server and root path. It mounts the root path via NFS and reads in and transfers to the kernel: /netbsd. - The kernel probes and configures the devices, and then sends out another BOOTP request so it can find out its address, the NFS server, and path. It then mounts its root (/) via NFS and con- tinues. You will need to set up servers for BOOTP, TFTP and NFS. If you want to run a full system from the network, untar the NetBSD distribution into a directory on your server and NFS export that directory to the client. Make sure you put a kernel there as well, and create the device nodes in /dev with sh ./MAKEDEV all. Detailed instructions on netbooting can be found by visiting http://www.NetBSD.org/docs/network/netboot/ You'll want to map root to root (rather than the default nobody) when you export your root file system (/). A typical /etc/exports line on a NetBSD system would be: /usr/export/alpha -maproot=0 myclient.mydom.com One option is to load just the install kernel over the network but then proceed to a normal disk-based install and disk-based operation. (Perhaps the alpha doesn't have a floppy drive, or you just don't want to use a Windows system to make the floppy; we understand.) For this case, you still need to export an NFS root, but the only thing it needs to have in it is the instkernel image from the distri- bution. The gzipped image can be booted directly; it is not necessary to uncompress it first. The console will be using TFTP to load the NetBSD boot program, so for the TFTP setup, you need to copy the second stage bootstrap, netboot, into an appropriately named file such as boot.netbsd.alpha in the directory used by your TFTP server. If you extracted a full snapshot, you can get the netboot program from /usr/mdec/netboot; if not, you can get this from the installation/netboot directory where you found the alpha distribution. For the BOOTP server you need to specify the: - hardware type (Ethernet) - hardware address (Ethernet MAC address) - IP address of the client - subnet mask of the client - address of of the TFTP/NFS server - name of the second stage bootstrap loaded via TFTP - path to the root for the client (mounted via NFS) Here's an example for a UNIX-like system running bootpd: myhost.mydom.com: :ht=ethernet:ha=0000c0391ae4:\ :ip=192.168.1.2:sm=255.255.255.0:\ :sa=192.168.1.1:bf=boot.netbsd.alpha:rp=/usr/export/alpha: And here's an example for a UNIX-like system running the ISC dhcpd: host axp { hardware ethernet 0:0:c0:39:1a:e4; fixed-address 192.168.1.2; option host-name "myhost.mydom.com"; filename "boot.netbsd.alpha"; option root-path "/usr/export/alpha"; option domain-name-servers 192.168.1.1; option broadcast-address 255.255.255.0; option domain-name "my.domain"; } The only Ethernet device the console on most alpha systems knows how to boot from is the onboard Ethernet interface or a DEC Tulip (21040, 21041, 21140) PCI Ethernet card. Some older SMC 100 Mbps cards that use this chip have been known to work as well. Many older systems will not be able to use the newer 2.0 stepping of the 21140, however. If your system appears not to be receiving packets, this may be the problem. (You may or may not be able to update your firmware to fix this; see http://www.NetBSD.org/ports/alpha/ for more information on this.) In general, 10 Mb cards from manufac- turers other than DEC will work, and 100 Mb cards not from DEC will not. Once you're set up, you should be able to boot with: >>> boot -proto bootp ewa0 You should permanently set your protocol to BOOTP with: >>> set ewa0_protocols bootp The 3000 series of Turbochannel systems and certain other models use old SRM, do not have a -proto option and use different device names. They also tend to not netboot very well so you probably don't need to worry about this section. However, if you want to give it a try, note the following differences: - There is no -proto argument, or ewa0_protocols variable. Old SRM uses bootp if the device name is given as ez0. - The use of the setnetbootinfo(8) program will probably also be necessary, as it is unlikely that an SRM from that era will properly communicate the ethernet HW address to the boot program. - Example: >>> boot ez0 Running the sysinst installation program 1. Introduction Using sysinst, installing NetBSD is a relatively easy process. Still, you should read this document and have it in hand when doing the installation process. This document tries to be a good guide to the installation, and as such, covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. Possible hardware problems Should you encounter hardware problems during installation, try rebooting after unplugging removable devices you don't need for installation. Non-removable devices can be disabled with userconf (use boot -c to enter it). 3. General The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installation system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst pro- gram from the command prompt. It is not necessary to reboot. 4. Quick install First, let's describe a quick install. The other sections of this document go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instruc- tions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. o What you need. - The distribution sets (in this example, they are on CD). - A CD-ROM drive (SCSI or ATAPI), a hard disk and a minimum of 32 MB of memory installed. - The hard disk should have at least 200 + n megabytes of space free, where n is the number of megabytes of main mem- ory in your system. If you wish to install the X Window System as well, you will need at least 215 MB more. o The Quick Installation - Insert the CD into the drive and boot the computer. Type >>> B DQA0 Note: This is only an example, and DQA0 may not be the proper device, depending on your hardware configura- tion. .***********************************************. * NetBSD-5.2 Install System * * * *>a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * x: Exit Install System * .***********************************************. - If you wish, you can configure some network settings immedi- ately by choosing the Utility menu and then Configure network. It isn't actually required at this point, but it may be more convenient. Go back to the main menu. - Choose install. - You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. - After your disk has been prepared, choose CD-ROM as the medium. The default values for the path and device should be ok. - After all the files have been unpacked, go back to the main menu and select reboot. - NetBSD will now boot. If you haven't already done so in sysinst, you should log in as root and set a password for that account. You are also advised to edit /etc/rc.conf to match your needs. - Your installation is now complete. 5. Booting NetBSD Boot your machine. The boot loader will start, and will print a countdown and begin booting. The most important thing to know is that wd0 is NetBSD's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 6. Network configuration If you do not intend to use networking during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu and select the Configure network option. If you only want to temporarily use net- working during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response when asked to provide a server. 7. Installation drive selection and parameters To start the installation, select Install NetBSD to hard disk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. You should see disk names like wd0, wd1, sd0 or sd1. 8. Selecting which sets to install The next step is to choose which distribution sets you wish to install. Options are provided for full, minimal, and custom instal- lations. If you choose sets on your own, base, etc, and a kernel must be selected. 9. Partitioning the disk o Which portion of the disk to use. You will be asked if you want to use the entire disk or only part of the disk. If you decide to use the entire disk for NetBSD, sysinst will check for the presence of other operating systems and you will be asked to confirm that you want to over- write these. 10. Editing the NetBSD disklabel The partition table of the NetBSD part of a disk is called a disklabel. If your disk already has a disklabel written to it, you can choose Use existing partition sizes. Otherwise, select Set sizes of NetBSD partitions. After you have chosen your partitions and their sizes (or if you opted to use the existing partitions), you will be presented with the layout of the NetBSD disklabel and given one more chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap parti- tion has a special type called swap. Some partitions in the diskla- bel have a fixed purpose. a Root partition (/) b Swap partition. c The NetBSD portion of the disk. d-h Available for other use. Traditionally, d is the par- tition mounted on /usr, but this is historical prac- tice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it something different, make sure the name is a single word and con- tains no special characters. You don't need to remember this name. 11. Preparing your hard disk You are now at the point of no return. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to pro- ceed, select yes. The install program will now label your disk and make the file sys- tems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are running. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Otherwise, you can continue the installa- tion program after pressing the return key. 12. Getting the distribution sets The NetBSD distribution consists of a number of sets that come in the form of gzipped tarfiles. At this point, you will be presented with a menu which enables you to choose from one of the following methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 13. Installation from CD-ROM When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM drive (usually cd0), and the directory name on the CD-ROM where the distribution files are. sysinst will then check if the files are indeed available in the specified location, and proceed to the actual extraction of the sets. 14. Installation using ftp To be able to install using ftp, you first need to configure your network setup if you haven't already done so. sysinst will do this for you, asking you if you want to use DHCP. If you do not use DHCP, you can enter network configuration details yourself. If you do not have DNS set up for the machine that you are installing on, you can just press RETURN in answer to this question, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS, you will need to specify an IP address instead of a hostname for the ftp server. sysinst will proceed to transfer all the default set files from the remote site to your hard disk. 15. Installation using NFS To be able to install using NFS, you first need to configure your network setup if you haven't already done so. sysinst will do this for you, asking you if you want to use DHCP. If you do not use DHCP, you can enter network configuration details yourself. If you do not have DNS set up for the machine that you are installing on, you can just press RETURN in answer to this question, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e., correctly exported to your machine. If you did not set up DNS, you will need to specify an IP address instead of a hostname for the NFS server. 16. Installation from an unmounted file system In order to install from a local file system, you will need to spec- ify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location. 17. Installation from a local directory This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file sys- tem that is already accessible. sysinst will ask you for the name of this directory. 18. Extracting the distribution sets Before extraction begins, you can elect to watch the files being extracted; the name of each file that is extracted will be shown. This can slow down the installation process considerably on machines with slow graphics consoles or serial consoles. Alternatively, you can choose to see a progress bar. This is the preferred option as it shows progress without significantly slowing down the installa- tion process. After all the files have been extracted, the device node files will be created. If you have already configured networking, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the network configuration files. The next menu will allow you to select the time zone that you're in, to make sure your clock has the right offset from UTC. Finally you will be asked to select a password encryption algorithm and can then set a password for the "root" account, to prevent the machine from coming up without access restrictions. 19. Finalizing your installation Congratulations, you have successfully installed NetBSD 5.2. You can now reboot the machine and boot NetBSD from hard disk. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state. The most important steps are described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the sys- tem asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi- user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). When you have finished editing /etc/rc.conf, type exit at the prompt to leave the single-user shell and continue with the multi-user boot. Other values that may need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute. You may also need to add an ifconfig_int for your network interface, along the lines of ifconfig_le0="inet 192.0.2.123 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_le0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. You should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you installed the X Window System, you may want to read the chap- ter about X in the NetBSD Guide: http://netbsd.org/docs/guide/en/chap-x.html 5. Installing third party packages If you wish to install any of the software freely available for UNIX-like systems you are strongly advised to first check the NetBSD package system, pkgsrc. pkgsrc automatically handles any changes necessary to make the software run on NetBSD. This includes the retrieval and installation of any other packages on which the soft- ware may depend. o More information on the package system is available at http://www.NetBSD.org/docs/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc/README.html o Precompiled binaries can be found at ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/ usually in the alpha/5.2/All subdir. You can install them with the following commands under sh(1): # PKG_PATH=ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/alpha/5.2/All # export PKG_PATH # pkg_add -v tcsh # pkg_add -v bash # pkg_add -v perl # pkg_add -v apache # pkg_add -v kde # pkg_add -v firefox ... If you are using csh(1) then replace the first two lines with the following: # setenv PKG_PATH ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/alpha/5.2/All Note: Some mirror sites don't mirror the /pub/pkgsrc directory. If you would like to use such mirrors, you could also try the /pub/NetBSD/packages/current-packages/NetBSD/alpha/5.2/All directory, which may have the same contents. The above commands will install the Tenex-csh and Bourne Again shells, the Perl programming language, Apache web server, KDE desktop environment and the Firefox web browser as well as all the packages they depend on. Note: In some cases the pkg_add(1) command will complain about a version mismatch of packages with a message like the following: Warning: package `foo' was built for a different version of the OS: NetBSD/i386 M.N (pkg) vs. NetBSD/i386 5.2 (this host), This warning is harmless if the formal major release num- bers are the same between the pkg and your host. Please refer to the NetBSD release glossary and graphs at http://www.NetBSD.org/releases/release-map.html for more information about NetBSD's release numbering scheme. o The framework for compiling packages can be obtained by retriev- ing the file ftp://ftp.NetBSD.org/pub/NetBSD/packages/pkgsrc.tar.gz It is typically extracted into /usr/pkgsrc (though other loca- tions work fine) with the commands: # cd /usr # tar -zxpf pkgsrc.tar.gz After extracting, see the doc/pkgsrc.txt file in the extraction directory (e.g., /usr/pkgsrc/doc/pkgsrc.txt) for more informa- tion. 6. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/postfix/main.cf file will almost definitely need to be adjusted. If you prefer a different MTA, then install it using pkgsrc or by hand and adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the man- ual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System The easiest way to upgrade to NetBSD 5.2 is with binaries, and that is the method documented here. To do the upgrade, you must have one form of boot media available. You must also have at least the base and kern binary distribution sets avail- able. Finally, you must have sufficient disk space available to install the new binaries. Since files already installed on the system are over- written in place, you only need additional free space for files which weren't previously installed or to account for growth of the sets between releases. If you have a few megabytes free on each of your root (/) and /usr partitions, you should have enough space. Since upgrading involves replacing the kernel, boot blocks, and most of the system binaries, it has the potential to cause data loss. You are strongly advised to back up any important data on the NetBSD partition or on another operating system's partition on your disk before beginning the upgrade process. The upgrade procedure is similar to an installation, but without the hard disk partitioning. sysinst will attempt to merge the settings stored in your /etc directory with the new version of NetBSD. Also, file systems are checked before unpacking the sets. Fetching the binary sets is done in the same manner as the installation procedure; refer to the installa- tion part of the document for help. After a new kernel has been copied to your hard disk, your machine is a complete NetBSD 5.2 system. However, that doesn't mean that you're fin- ished with the upgrade process. You will probably want to update the set of device nodes you have in /dev. If you've changed the contents of /dev by hand, you will need to be careful about this, but if not, you can just cd into /dev, and run the command: # sh MAKEDEV all Finally, you will want to delete old binaries that were part of the ver- sion of NetBSD that you upgraded from and have since been removed from the NetBSD distribution. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 5.2. If your port uses X.Org and you see messages from the X server indicating that no devices were found, you may need to run X -configure and update your existing xorg.conf to use the BusID line from the newly-generated config file. Dual-head support for PC systems has become broken for many configura- tions with the update to xorg-server 1.6.x, which has removed the user- land PCI configuration mechanism, and needs to rely upon the OS. We hope to correct this for future releases. Workaround: The only workaround is non-trivial and requires programming several PCI BAR registers as they previously were in NetBSD 5.0. If you are updating to NetBSD 5.2 without the aid of sysinst or postin- stall and your port uses X.Org, be sure to remove /usr/X11R7/lib/X11/xkb/symbols/pc before extracting the xbase set. In the version of X.Org shipped with 5.0, this was a directory, but in more recent X.Org versions it is a file. pkg_install now depends on the pkgdb cache for automatic conflict detec- tion. It is recommended to rebuild the cache with # pkg_admin rebuild audit-packages.conf(5) has been superseded by pkg_install.conf(5). The default configuration is the same. Support for pkg_view(1) has been retired. The functionality of audit-packages(1) and download-vulnerability-list(1) has moved into pkg_admin(1). However, wrapper scripts that handle the common use cases are provided. Issues when running older binaries on NetBSD 5.2 The pthread libraries from previous versions of NetBSD require that the sysctl(3) node kern.no_sa_support be set to 0. This affects the follow- ing environments: o Running a 5.x kernel with an older userland. o Running an older userland inside a chroot'ed environment on a 5.x system. o Running older statically linked pthread applications. The 5.x kernel defaults to 0 for kern.no_sa_support, which covers the first case. However, please note that a full installation of 5.x (either from scratch or through an upgrade) will set kern.no_sa_support to 1 dur- ing the boot process. This means that for the last two cases, you will have to manually set kern.no_sa_support to 0, using either the sysctl(8) command or through sysctl.conf(5). Note that sysinst will automatically invoke postinstall fix and thus all issues that are fixed by postinstall by default (see below) will be handled. Issues affecting an upgrade from NetBSD 3.x releases See the section below on upgrading from NetBSD 4.x as well. The following issues can generally be resolved by running postinstall with the etc set: postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* - /etc/envsys.conf The following issues need to be resolved manually: o The users `_proxy', `_rwhod', and `_sdpd' and the groups `_proxy', `_rwhod' and `_sdpd' need to be created and the user `uucp' needs to be updated. o A number of things were removed in the NetBSD 4.0 release, including: the evbsh5 port, the Fortran 77 compiler (g77), NETCCITT, NETNS, Sendmail, Sushi, UUCP, and Vinum. If you were using any of these, please see the "Components removed from NetBSD" at http://www.NetBSD.org/releases/formal-4/NetBSD-4.0.html#removals o The replacement of Sendmail by Postfix can be handled automati- cally by postinstall but it is not done by default. If you want to transition to Postfix, the command postinstall -s /path/to/etc.tgz fix mailerconf will update your /etc/mailer.conf file to use Postfix as the MTA. When using sysinst to upgrade the system, it will ask if you want this to be done. Note that if you have a customized Sendmail setup, you need to set up Postfix in an equivalent way; there is no tool for auto- matic conversion of Sendmail configuration to a Postfix one. Postfix will be started automatically when the system boots. You may see messages like "$sendmail is not set properly" at boot. You can suppress them by removing /etc/rc.d/sendmail and /etc/rc.d/smmsp. Those files and other parts of sendmail con- figuration like files under /usr/share/sendmail are not removed by default while upgrading for those who want to continue using sendmail from outside the base system. If you want to delete them, postinstall can be used: postinstall -s /path/to/etc.tgz fix sendmail Issues affecting an upgrade from NetBSD 4.x releases The following issues can generally be resolved by running postinstall with the etc set: postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* - /etc/envsys.conf The following issues need to be resolved manually: o The users `_httpd' and `_timedc' and the groups `_httpd' and `_timedc' need to be created. o Unprivileged use of the mount(8) command now requires the nosuid and nodev options to be explicitly specified. Previ- ously, these options were automatically enforced even if they were not explicitly specified. o A number of things have been removed from the NetBSD 5.2 release. See the "Components removed from NetBSD" section near the beginning of this document for a list. Using online NetBSD documentation Documentation is available if you installed the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are o intro(1), o man(1), o apropos(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter # man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter # apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. See http://www.NetBSD.org/mailinglists/ for a web interface. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Bugs also can be submitted and queried with the web interface at http://www.NetBSD.org/support/send-pr.html There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/mailinglists/ If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-users@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their work on BSD systems, support, and encouragement. o The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. o The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. o The Lulea Academic Computer Society for providing the backup services server. o The Columbia University Computer Science Department for hosting the NYC build cluster. o The Western Washington University Computer Science Department for running the WWU build cluster. o The many organizations that provide NetBSD mirror sites. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o We list the individuals and organizations that have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it at http://www.NetBSD.org/donations/ (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to be mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Alistair Crooks agc@NetBSD.org Quentin Garnier cube@NetBSD.org Matt Thomas matt@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): Erik Berls cyber@NetBSD.org cobalt Manuel Bouyer bouyer@NetBSD.org xen Simon Burge simonb@NetBSD.org evbmips Simon Burge simonb@NetBSD.org pmax Simon Burge simonb@NetBSD.org sbmips Julian Coleman jdc@NetBSD.org atari Marcus Comstedt marcus@NetBSD.org dreamcast Andrew Doran ad@NetBSD.org amd64 Andrew Doran ad@NetBSD.org i386 Matthias Drochner drochner@NetBSD.org cesfic Gavan Fantom gavan@NetBSD.org iyonix Jaime A Fournier ober@NetBSD.org zaurus Matt Fredette fredette@NetBSD.org sun2 Ichiro FUKUHARA ichiro@NetBSD.org hpcarm Chris Gilbert chris@NetBSD.org cats Ben Harris bjh21@NetBSD.org acorn26 Ross Harvey ross@NetBSD.org alpha Nick Hudson skrll@NetBSD.org hp700 Martin Husemann martin@NetBSD.org sparc64 IWAMOTO Toshihiro toshii@NetBSD.org hpcarm Darrin Jewell dbj@NetBSD.org next68k Soren Jorvang soren@NetBSD.org sgimips Wayne Knowles wdk@NetBSD.org mipsco Takayoshi Kochi kochi@NetBSD.org ia64 Paul Kranenburg pk@NetBSD.org sparc Michael Lorenz macallan@NetBSD.org macppc Anders Magnusson ragge@NetBSD.org vax Cherry G. Mathew cherry@NetBSD.org ia64 NISHIMURA Takeshi nsmrtks@NetBSD.org x68k Tohru Nishimura nisimura@NetBSD.org luna68k Tohru Nishimura nisimura@NetBSD.org sandpoint Andrey Petrov petrov@NetBSD.org sparc64 Scott Reynolds scottr@NetBSD.org mac68k Tim Rightnour garbled@NetBSD.org ofppc Tim Rightnour garbled@NetBSD.org prep Tim Rightnour garbled@NetBSD.org rs6000 Noriyuki Soda soda@NetBSD.org arc Ignatios Souvatzis is@NetBSD.org amiga Jonathan Stone jonathan@NetBSD.org pmax Shin Takemura takemura@NetBSD.org hpcmips Matt Thomas matt@NetBSD.org alpha Matt Thomas matt@NetBSD.org netwinder Jason Thorpe thorpej@NetBSD.org algor Jason Thorpe thorpej@NetBSD.org evbarm Jason Thorpe thorpej@NetBSD.org shark Izumi Tsutsui tsutsui@NetBSD.org ews4800mips Izumi Tsutsui tsutsui@NetBSD.org hp300 Izumi Tsutsui tsutsui@NetBSD.org news68k Valeriy E. Ushakov uwe@NetBSD.org landisk Nathan Williams nathanw@NetBSD.org sun3 Steve Woodford scw@NetBSD.org evbppc Steve Woodford scw@NetBSD.org mvme68k Steve Woodford scw@NetBSD.org mvmeppc Reinoud Zandijk reinoud@NetBSD.org acorn32 The NetBSD 5.2 Release Engineering team: Manuel Bouyer bouyer@NetBSD.org David Brownlee abs@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Havard Eidnes he@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org John Heasley heas@NetBSD.org Geert Hendrickx ghen@NetBSD.org Soren Jacobsen snj@NetBSD.org Phil Nelson phil@NetBSD.org Jeff Rizzo riz@NetBSD.org Stephen Borrill sborrill@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Christoph Badura bad@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Alan Barrett apb@NetBSD.org Grant Beattie grant@NetBSD.org Jason Beegan jtb@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Mason Loring Bliss mason@NetBSD.org Charles Blundell cb@NetBSD.org Rafal Boni rafal@NetBSD.org Stephen Borrill sborrill@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org John Brezak brezak@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Frederick Bruckman fredb@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org Pavel Cahyna pavel@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Daniel Carosone dan@NetBSD.org Dave Carrel carrel@NetBSD.org James Chacon jmc@NetBSD.org Mihai Chelaru kefren@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Ben Collver ben@NetBSD.org Marcus Comstedt marcus@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Aidan Cully aidan@NetBSD.org Garrett D'Amore gdamore@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Jed Davis jld@NetBSD.org Matt DeBergalis deberg@NetBSD.org Arnaud Degroote degroote@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Havard Eidnes he@NetBSD.org Jaime A Fournier ober@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hauke Fath hauke@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt J. Fleming mjf@NetBSD.org Marty Fouts marty@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Brian Ginsbach ginsbach@NetBSD.org Paul Goyette pgoyette@NetBSD.org Michael Graff explorer@NetBSD.org Brian C. Grayson bgrayson@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Ulrich Habel rhaen@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org Adam Hamsik haad@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Ben Harris bjh21@NetBSD.org Ross Harvey ross@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org HAYAKAWA Koichi haya@NetBSD.org John Heasley heas@NetBSD.org Geert Hendrickx ghen@NetBSD.org Rene Hexel rh@NetBSD.org Iain Hibbert plunky@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Adam Hoka ahoka@NetBSD.org Jachym Holecek freza@NetBSD.org David A. Holland dholland@NetBSD.org Christian E. Hopps chopps@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hornquist Astrand lha@NetBSD.org Roland Illig rillig@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Nicolas Joly njoly@NetBSD.org Chris Jones cjones@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Masanori Kanaoka kanaoka@NetBSD.org Antti Kantee pooka@NetBSD.org Frank Kardel kardel@NetBSD.org Mattias Karlsson keihan@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Mario Kemper magick@NetBSD.org Min Sik Kim minskim@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org John Kohl jtk@NetBSD.org Daniel de Kok daniel@NetBSD.org Jonathan A. Kollasch jakllsch@NetBSD.org Paul Kranenburg pk@NetBSD.org Lubomir Kundrak lkundrak@NetBSD.org Jochen Kunz jkunz@NetBSD.org Martti Kuparinen martti@NetBSD.org Kentaro A. Kurahone kurahone@NetBSD.org Arnaud Lacombe alc@NetBSD.org Kevin Lahey kml@NetBSD.org David Laight dsl@NetBSD.org Johnny C. Lam jlam@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Tonnerre Lombard tonnerre@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org Paul Mackerras paulus@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org Anders Magnusson ragge@NetBSD.org Cherry G. Mathew cherry@NetBSD.org David Maxwell david@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Perry Metzger perry@NetBSD.org Luke Mewburn lukem@NetBSD.org Jean-Yves Migeon jym@NetBSD.org Brook Milligan brook@NetBSD.org Minoura Makoto minoura@NetBSD.org Simas Mockevicius symka@NetBSD.org der Mouse mouse@NetBSD.org Joseph Myers jsm@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Phil Nelson phil@NetBSD.org John Nemeth jnemeth@NetBSD.org Bob Nestor rnestor@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Tobias Nygren tnn@NetBSD.org OBATA Akio obache@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Rui Paulo rpaulo@NetBSD.org Jonathan Perkin sketch@NetBSD.org Andrey Petrov petrov@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Peter Postma peter@NetBSD.org Dante Profeta dante@NetBSD.org Chris Provenzano proven@NetBSD.org Niels Provos provos@NetBSD.org Mindaugas Rasiukevicius rmind@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Michael Richardson mcr@NetBSD.org Tim Rightnour garbled@NetBSD.org Alan Ritter rittera@NetBSD.org Jeff Rizzo riz@NetBSD.org Hans Rosenfeld hans@NetBSD.org Gordon Ross gwr@NetBSD.org Steve Rumble rumble@NetBSD.org Ilpo Ruotsalainen lonewolf@NetBSD.org Heiko W. Rupp hwr@NetBSD.org Blair J. Sadewitz bjs@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Silke Scheler silke@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Takeshi Shibagaki shiba@NetBSD.org Naoto Shimazaki igy@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Daniel Sieger dsieger@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org SOMEYA Yoshihiko someya@NetBSD.org Bill Sommerfeld sommerfeld@NetBSD.org Jorg Sonnenberger joerg@NetBSD.org Ignatios Souvatzis is@NetBSD.org T K Spindler dogcow@NetBSD.org Bill Squier groo@NetBSD.org Jonathan Stone jonathan@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org SUNAGAWA Keiki kei@NetBSD.org Kimmo Suominen kim@NetBSD.org Robert Swindells rjs@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Ian Lance Taylor ian@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Todd Whitesel toddpw@NetBSD.org Frank Wille phx@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Dan Winship danw@NetBSD.org Jim Wise jwise@NetBSD.org Michael Wolfson mbw@NetBSD.org Colin Wood ender@NetBSD.org Steve Woodford scw@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org David Young dyoung@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Maria Zevenhoven maria7@NetBSD.org Christos Zoulas christos@NetBSD.org Other contributors: Dave Burgess burgess@cynjut.infonet.net Brian R. Gaeke brg@dgate.org Brad Grantham grantham@tenon.com Lawrence Kesteloot kesteloo@cs.unc.edu Waldi Ravens waldi@moacs.indiv.nl.net Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trade- marks of their respective owners. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: NetBSD is a registered trademark of The NetBSD Foundation, Inc. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product contains software developed by Ignatios Souvatzis for the NetBSD project. This product contains software written by Ignatios Souvatzis and Michael L. Hitch for the NetBSD project. This product includes software developed by Intel Corporation and its contributors. This product contains software written by Michael L. Hitch for the NetBSD project. This product includes software developed by Microsoft. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) This product includes cryptographic software written by Eric Young (eay@mincom.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Division, US Naval Research Laboratory. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Gordon W. Ross and Leo Wep- pelman. This product includes software developed by Hellmuth Michaelis and Joerg Wunsch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Uni- versity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Adrian Portelli for the NetBSD project. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Alistair G. Crooks. This product includes software developed by Alistair G. Crooks. for the NetBSD project. This product includes software developed by Allen Briggs. This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brad Pepers This product includes software developed by Bradley A. Grantham. This product includes software developed by Brini. This product includes software developed by Bruce M. Simpson. This product includes software developed by Causality Limited. This product includes software developed by Charles D. Cranor and Seth Widoff. This product includes software developed by Charles D. Cranor and Wash- ington University. This product includes software developed by Charles D. Cranor, Washington University, and the University of California, Berkeley and its contribu- tors. This product includes software developed by Charles D. Cranor, Washington University, the University of California, Berkeley and its contributors. This product includes software developed by Charles D. Cranor. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christian Limpach. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Daan Vreeken. This product includes software developed by Daishi Kato This product includes software developed by Dale Rahn. This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Darrin B. Jewell This product includes software developed by David Miller. This product includes software developed by Dean Huxley. This product includes software developed by Eduardo Horvath. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@min- com.oz.au) This product includes software developed by Eric Young (eay@crypt- soft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by K. Kobayashi. This product includes software developed by K. Kobayashi and H. Shimokawa. This product includes software developed by Ezra Story and by Kari Met- tinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Florian Stoehr. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Garrett D'Amore. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Gordon W. Ross This product includes software developed by HAYAKAWA Koichi. This product includes software developed by Harvard University and its contributors. This product includes software developed by Harvard University. This product includes software developed by Henrik Vestergaard Draboel. This product includes software developed by Herb Peyerl. This product includes software developed by Hidetoshi Shimokawa. This product includes software developed by Hubert Feyrer for the NetBSD Project. This product includes software developed by Ian F. Darwin and others. This product includes software developed by Ian W. Dall. This product includes software developed by Ichiro FUKUHARA. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jared D. McNeill. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/ This product includes software developed by Jeremy C. Reed for the NetBSD project. This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Jukka Marin. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berke- ley and its contributors. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Leo Weppelman for the NetBSD Project. This product includes software developed by Leo Weppelman. This product includes software developed by Lloyd Parkes. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Manuel Bouyer. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Mats O Jansson and Charles D. Cranor. This product includes software developed by Mats O Jansson. This product includes software developed by Matt DeBergalis This product includes software developed by Matthew Fredette. This product includes software developed by Matthias Pfaller. This product includes software developed by Michael Graff for the NetBSD Project. This product includes software developed by Michael Graff. This product includes software developed by Michael L. Hitch. This product includes software developed by Michael Shalayeff. This product includes software developed by Michael Smith. This product includes software developed by Mike Pritchard. This product includes software developed by Mike Pritchard and contribu- tors. This product includes software developed by Minoura Makoto. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Onno van der Linden. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Roland C. Dowdeswell. This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Soren S. Jorvang. This product includes software developed by Stephan Thesing. This product includes software developed by Steve Woodford. This product includes software developed by Steven M. Bellovin. This product includes software developed by Takashi Hamada. This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by Tetsuya Isaki. This product includes software developed by Thomas Gerner This product includes software developed by Tobias Weingartner. This product includes software developed by Todd C. Miller. This product includes software developed by Tohru Nishimura and Reinoud Zandijk for the NetBSD Project. This product includes software developed by Tohru Nishimura for the NetBSD Project. This product includes software developed by Tohru Nishimura. for the NetBSD Project. This product includes software developed by TooLs GmbH. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contrib- utors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki. This product includes software developed by Yen Yen Lim and North Dakota State University. This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the Charles D. Cranor, Wash- ington University, University of California, Berkeley and its contribu- tors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) This product includes software developed by the PocketBSD project and its contributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Develop- ment Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia Uni- versity. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the Urbana-Champaign Indepen- dent Media Center. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Labora- tory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Chris- tos Zoulas This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Igna- tios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed by Kyma Systems. This product includes software developed for the NetBSD Project by Kyma Systems LLC. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Michael L. Hitch. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden This product includes software developed for the NetBSD Project by Alle- gro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Labora- tory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Marshall M. Midden. This product includes software developed or owned by Caldera Interna- tional, Inc. The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation. In the following statement, the phrase ``this text'' refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in NetBSD, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html. This notice shall appear on any product containing this material In the following statement, "This software" refers to the parallel port driver: This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. The End NetBSD November 27, 2012 NetBSD