INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL -- Installation procedure for NetBSD/emips. CONTENTS About this Document............................................2 What is NetBSD?................................................2 Changes Between The NetBSD 6.0 and 6.0.1 Releases..............3 Security Fixes..............................................3 General kernel..............................................3 Networking..................................................3 File systems................................................3 Drivers.....................................................3 Platforms...................................................3 Userland changes............................................4 The NetBSD Foundation..........................................4 Sources of NetBSD..............................................4 NetBSD 6.0.1 Release Contents..................................4 NetBSD/emips subdirectory structure.........................5 Binary distribution sets....................................5 NetBSD/emips System Requirements and Supported Devices.........6 Supported machines..........................................7 Supported devices...........................................7 Getting the NetBSD System on to Useful Media...................7 Preparing your System for NetBSD installation..................8 Installing the NetBSD System...................................8 Install via a NetBSD CD-ROM.................................9 Installing from an existing system.........................10 Install via diskimage......................................10 Install via netboot install kernel.........................10 Install via diskless boot..................................11 Once you've booted the diskimage...........................11 Running the sysinst installation program...................12 Introduction............................................12 Possible hardware problems..............................12 General.................................................12 Quick install...........................................12 Booting NetBSD..........................................13 Network configuration...................................13 Installation drive selection and parameters.............13 Selecting which sets to install.........................14 Partitioning the disk...................................14 Preparing your hard disk................................14 Getting the distribution sets...........................15 Installation from CD-ROM................................15 Installation using ftp..................................15 Installation using NFS..................................15 Installation from an unmounted file system..............16 Installation from a local directory.....................16 Extracting the distribution sets........................16 Configure additional items..............................16 Finalizing your installation............................16 Post installation steps.......................................16 Upgrading a previously-installed NetBSD System................19 Compatibility Issues With Previous NetBSD Releases............19 Issues affecting an upgrade from NetBSD 5.x releases.......19 Issues affecting an upgrade from NetBSD 4.x releases.......20 Using online NetBSD documentation.............................20 Administrivia.................................................21 Thanks go to..................................................21 We are........................................................22 Legal Mumbo-Jumbo.............................................28 The End.......................................................33 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 6.0.1 on the emips platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX-like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on 57 different system architectures (ports) across 15 distinct CPU families, and is being ported to more. The NetBSD 6.0.1 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distribution. Please see the NetBSD web site at http://www.NetBSD.org/ for information on them.) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Changes Between The NetBSD 6.0 and 6.0.1 Releases The complete list of changes can be found in the CHANGES-6.0.1: http://ftp.NetBSD.org/pub/NetBSD/NetBSD-6.0.1/CHANGES-6.0.1 file in the top level directory of the NetBSD 6.0.1 release tree. An abbreviated list is as follows: Security Fixes o expat: Fix CVE-2012-1147, CVE-2012-1148 and CVE-2012-0876. o BIND: Address CVE-2012-5688: Named could die on specific queries with dns64 enabled. General kernel o posix_spawn(): Fix processes with attributes. o Resolve races between vget() and vrele() resulting in vget() return- ing dead vnodes. o Prevent crash when unsupported fd's are used with kevent. o Networking o Fix "atomic fragments" for IPv6. o ipf: Fix alignment issues in ipmon. (PR#47101): http://gnats.NetBSD.org/47101 o npf: handle delayed checksums in the network stack. (PR#47235): http://gnats.NetBSD.org/47235 File systems o smbfs: Make smbfs actually work on big-endian ports. Drivers o ciss(4): don't try to handle sensors if there aren't any. Platforms o x86 ( i386, amd64): - Work around a possible gcc bug generating bad assembler code. (PR#45673): http://gnats.NetBSD.org/45673 - Disable C1E on AMD K8 CPUs, to prevent freeze during boot. o xen: - Prevent a memory corruption issue that locks up a Xen DomU, and can potentially cause file system corruption. ( PR#47056,: http://gnats.NetBSD.org/47056 PR#47057: http://gnats.NetBSD.org/47057 ) - Fix: Xen Dom0 NetBSD kernel could crash by adding duplicate xen- watches. Userland changes o Update to tzdata2012j. o cdb: don't refuse to open databases without entries or keys. o Address graphics corruption in recent Cairo, manifested most commonly by certain rendered text sections appearing as solid rectangular blocks of color. The NetBSD Foundation The NetBSD Foundation is a tax exempt, not-for-profit 501(c)(3) corpora- tion that devotes itself to the traditional goals and Spirit of the NetBSD Project and owns the trademark of the word ``NetBSD''. It sup- ports the design, development, and adoption of NetBSD worldwide. More information on the NetBSD Foundation, its composition, aims, and work can be found at: http://www.NetBSD.org/foundation/ Sources of NetBSD Refer to http://www.NetBSD.org/mirrors/ NetBSD 6.0.1 Release Contents The root directory of the NetBSD 6.0.1 release is organized as follows: .../NetBSD-6.0.1/ CHANGES Changes between the 5.0 and 6.0 releases. CHANGES-6.0 Changes between the initial 6.0 branch and final release of 6.0. CHANGES-6.0.1 Changes between the 6.0 and 6.0.1 releases. CHANGES.prev Changes in previous NetBSD releases. LAST_MINUTE Last minute changes and notes about the release. README.files README describing the distribution's contents. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 6.0.1 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. src This set contains all of the base NetBSD 6.0.1 sources which are not in gnusrc, sharesrc, or syssrc. syssrc This set contains the sources to the NetBSD 6.0.1 kernel for all architectures as well as the config(1) utility. xsrc This set contains the sources to the X Window System. All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # cd / ; tar -zxpf set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: MD5 MD5 digests in the format produced by the command: cksum -a MD5 file. SHA512 SHA512 digests in the format produced by the command: cksum -a SHA512 file. The SHA512 digest is safer, but MD5 checksums are provided so that a wider range of operating systems can check the integrity of the release files. NetBSD/emips subdirectory structure The emips-specific portion of the NetBSD 6.0.1 release is found in the emips subdirectory of the distribution: .../NetBSD-6.0.1/emips/. It con- tains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-GENERIC.gz A gzipped NetBSD kernel containing code for everything supported in this release. sets/ emips binary distribution sets; see below. installation/ misc/ Miscellaneous emips installation utilities; see installation section below. Binary distribution sets The NetBSD emips binary distribution sets contain the binaries which com- prise the NetBSD 6.0.1 release for emips. The binary distribution sets can be found in the emips/binary/sets subdirectory of the NetBSD 6.0.1 distribution tree, and are as follows: base The NetBSD 6.0.1 emips base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be mini- mally functional. comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. games This set includes the games and their manual pages. kern-GENERIC This set contains a NetBSD/emips 6.0.1 GENERIC kernel, named /netbsd. You must install this distribution set. man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. misc This set includes the system dictionaries, the typesettable doc- ument set, and other files from /usr/share. text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on X.Org. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. xcomp The extra libraries and include files needed to compile X source code. xfont Fonts needed by the X server and by X clients. xetc Configuration files for X which could be locally modified. xserver The X server. The emips binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xzpf command from the root directory ( / ) of your system. Note: Each directory in the emips binary distribution also has its own checksum files, just as the source distribution does. NetBSD/emips System Requirements and Supported Devices Supported machines o Xilinx Ml401 and Ml402 with Virtex-4 FPGAs. XUP board with Vir- tex-5 FPGAs. o BeSquare BEE3 system with four Xilinx Virtex-5 FPGAs. The minimal configuration requires 8 MB of RAM and ~60 MB of disk space. To install the entire system requires in excess of 800 MB of disk space, for any serious work at least 64 MB of RAM is recommended. The processor can address the full 4 GB of physical space, but configurations with more than 256 MB of RAM are currently untested. Supported devices o eMIPS serial line as console o Xilinx SystemACE Compact FLASH interface, using cards of any size. o Ethernet using 1 Gbps cabling, both on XUP and BEE3 systems. Getting the NetBSD System on to Useful Media Installation is supported from several media types, including: o CD-ROM / DVD o FTP o Remote NFS partition o Tape o Existing NetBSD partitions, if performing an upgrade The steps necessary to prepare the distribution sets for installation depend upon which installation medium you choose. The steps for the var- ious media are outlined below. CD-ROM / DVD Find out where the distribution set files are on the CD-ROM or DVD. Likely locations are binary/sets and emips/binary/sets. Proceed to the instructions on installation. FTP The preparations for this installation/upgrade method are easy; all you need to do is make sure that there's an FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. If you don't have DHCP available on your network, you will need to know the numeric IP address of that site, and, if it's not on a net- work directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once you have this information, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on pre- paring your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. NFS Place the NetBSD distribution sets you wish to install into a directory on an NFS server, and make that directory mountable by the machine on which you are installing or upgrading NetBSD. This will probably require modifying the /etc/exports file on the NFS server and resetting its mount daemon (mountd). (Both of these actions will probably require superuser privileges on the server.) You need to know the numeric IP address of the NFS server, and, if you don't have DHCP available on your network and the server is not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Once the NFS server is set up properly and you have the information mentioned above, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on pre- paring your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Tape To install NetBSD from a tape, you need to make a tape that contains the distribution set files, in `tar' format. If you're making the tape on a UNIX-like system, the easi- est way to do so is probably something like: # tar -cf tape_device dist_directories where tape_device is the name of the tape device that describes the tape drive you're using; possibly /dev/rst0, or something similar, but it will vary from system to sys- tem. (If you can't figure it out, ask your system adminis- trator.) In the above example, dist_directories are the distribution sets' directories, for the distribution sets you wish to place on the tape. For instance, to put the kern-GENERIC, base, and etc distributions on tape (in order to do the absolute minimum installation to a new disk), you would do the following: # cd .../NetBSD-6.0.1 # cd emips/binary # tar -cf tape_device kern-GENERIC base etc Note: You still need to fill in tape_device in the example. Once you have the files on the tape, you can proceed to the next step in the installation or upgrade process. If you're installing NetBSD from scratch, go to the section on preparing your hard disk, below. If you're upgrading an existing installation, go directly to the section on upgrading. Preparing your System for NetBSD installation First and foremost, before beginning the installation process, make sure you have a reliable backup of any data on your hard disk that you wish to keep. Mistakes in partitioning your hard disk may lead to data loss. Installing the NetBSD System Note: There may be updates to this procedure available from the NetBSD/emips web page at http://www.NetBSD.org/ports/emips/ . To install or upgrade NetBSD, you need to first boot an installation pro- gram and then interact with the screen-menu program sysinst. The instal- lation program actually consists of the NetBSD kernel plus an in-memory file system of utility programs. From most convenient to least convenient, the installation methods are: 1. Installation from an existing NetBSD system by booting the install kernel from an existing root file system (/). See the Installing from an existing system section later in these INSTALL notes. 2. Copying a bootable diskimage onto the beginning of a disk and installing onto that disk. See the Install via diskimage section later in these INSTALL notes. 3. Booting the install kernel over the network and installing onto a local disk. See the Install via netboot install kernel section later in these INSTALL notes. 4. Using a helper machine with a CompactFLASH controller to copy the bootable diskimage onto the beginning of a disk, and moving the disk to the target machine. See the Install via diskimage section later in these INSTALL notes. 5. For BEE3 machines that do not have local disk storage, you will need to set up an NFS server with a diskless root file system for trimmed-down network install kernel and run the installation system from the NFS root file system. NFS is also your only option for user storage. See the Install via diskless boot section later in these INSTALL notes. You should familiarize yourself with the hardware configuration on your machine or simulator. Be sure you know how to print the configuration of your machine, and how to boot from disk or network, as appropriate. To boot from disk, use: All systems: /netbsd To boot via TFTP, use boot: tftp You will also need to know the total size (in sectors) and the approxi- mate geometry of the disks you are installing onto, so that you can label your disks for the BSD fast file system (FFS). The kernel should cor- rectly detect the disk geometry. The sysinst tool will suggest these as the default. If you're installing NetBSD/emips for the first time it's a very good idea to pre-plan partition sizes for the disks on which you're installing NetBSD. Changing the size of partitions after you've installed is diffi- cult. If you do not have a spare bootable disk, it may be simpler to re- install NetBSD again from scratch. Assuming a classic partition scheme with separate / (root) and /usr file systems, a comfortable size for the NetBSD / partition is about 64 MB. A good initial size for the swap partition is twice the amount of physical memory in your machine. The default swap size is 64 MB, which is ade- quate for doing a full system build. A full binary installation, with X11R6 takes about 700 MB in /usr; a 1 GB /usr should be ample. Install via a NetBSD CD-ROM You can obtain the disk image or diskless boot tar file from the NetBSD 6.0.1 CD-ROM. To mount the CD-ROM from a NetBSD/emips host, type # mount -r -t cd9660 /dev/cdXc /mnt where X is the ID of the CD-ROM. The diskimage file can be found on the CD-ROM at the following location (relative to the mount point of the CD) emips/installation/diskimage/diskimage.gz and the diskless boot tar file can be found at emips/installation/netboot/diskimage.tgz Once you have located these files, continue on to either Install via netboot install kernel, Install via diskless boot, Install via diskimage or Installing from an existing system section later in the INSTALL notes. Installing from an existing system Using the bootloader you can boot the kernel located in: emips/binary/kernel/netbsd-INSTALL.gz Then boot using: All systems: /netbsd-INSTALL then continue to the Once you've booted the diskimage section Install via diskimage The diskimage file is in emips/installation/diskimage/diskimage.gz. It is shipped compressed and is around 1620 kbytes, uncompressing to exactly 2100 kbytes. To install the diskimage onto disk aceX on a NetBSD/emips system, do: # disklabel -W /dev/raceXc # gunzip -c diskimage.gz | dd of=/dev/raceXc bs=10240 On NetBSD/i386, the ``raw disk partition'' is the `d' partition, so do: # disklabel -W /dev/rsdXd # gunzip -c diskimage.gz | dd of=/dev/rsdXd bs=10240 On NetBSD, be sure to use disklabel -W to enable writing to the label area of the disk. If you forget this and/or use the `block' device, the dd command may silently fail. Then boot using: All systems: /netbsd then continue to the Once you've booted the diskimage section. Install via netboot install kernel Booting NetBSD/emips 6.0.1 install kernel over a network requires a BOOTP or DHCP server and a TFTP server. (These are usually all run on the same machine.) There are two basic stages to the boot: o The emips boot loader sends a BOOTP request to get its own address, the address of the TFTP server and the file to download. o It downloads the file name obtained from BOOTP, which is the install kernel, via TFTP and then executes it. You will need to set up servers for BOOTP and TFTP. For the BOOTP server you need to specify the: o hardware type (Ethernet) o hardware address (Ethernet MAC address) o IP address of the client o subnet mask of the client o address of the TFTP server o name of the kernel loaded via TFTP Here's an example for a UNIX-like system running bootpd: myhost.mydom.com:\ :ht=ethernet:ha=08002b123456:\ :ip=192.168.1.2:sm=255.255.255.0:\ :sa=192.168.1.1:bf=netbsd-INSTALL:\ :rp=/usr/export/emips: And here's an example for a UNIX-like system running the ISC dhcpd: host emips { hardware ethernet 08:0:2b:12:34:56; fixed-address 192.168.1.2; option host-name "myhost.mydom.com"; filename "netbsd-INSTALL"; option domain-name-servers 192.168.1.1; option broadcast-address 255.255.255.0; option domain-name "my.domain"; option root-path "/usr/export/emips"; } For the TFTP server, You will need to copy the netbsd-INSTALL kernel to the directory used by the TFTP server. Then boot using TFTP as described earlier. and continue to the Once you've booted the diskimage section. Install via diskless boot The file emips/installation/netboot/diskimage.tar.gz contains a suitable set of files for installing on an NFS server to set up a diskless root filesytem. (It is a tar copy of the contents of an installation ramdisk file system contained in the install kernel.) You will need to find an NFS server, unpack the tarfile, and setup BOOTP/dhcp service for your emips. Instructions for setting up an NFS server and diskless booting are on the NetBSD/emips netboot webpage at http://www.NetBSD.org/ports/emips/netboot.html Since the system install utility, sysinst, requires a read/write root, installing via diskless boot is only feasible if your NFS server exports the diskless root read-write. If this is not possible, you should install via other of the other installation procedures. Once you have booted the kernel, continue to the Once you've booted the diskimage section. Once you've booted the diskimage Once you've booted the installation kernel you will need to select your terminal type. Use vt100 for a serial console with a vt100-compatible terminal emulator, such as PuTTY, or xterm or xterms for a tip(1) or cu(1) connection running in an xterm(1). The system will then start the sysinst program. Running the sysinst installation program 1. Introduction Using sysinst, installing NetBSD is a relatively easy process. Still, you should read this document and have it in hand when doing the installation process. This document tries to be a good guide to the installation, and as such, covers many details for the sake of completeness. Do not let this discourage you; the install program is not hard to use. 2. Possible hardware problems Should you encounter hardware problems during installation, try rebooting after unplugging removable devices you don't need for installation. Non-removable devices can be disabled with userconf (use boot -c to enter it). 3. General The following is a walk-through of the steps you will take while getting NetBSD installed on your hard disk. sysinst is a menu driven installation system that allows for some freedom in doing the installation. Sometimes, questions will be asked and in many cases the default answer will be displayed in brackets (``[ ]'') after the question. If you wish to stop the installation, you may press CONTROL-C at any time, but if you do, you'll have to begin the installation process again from scratch by running the /sysinst pro- gram from the command prompt. It is not necessary to reboot. 4. Quick install First, let's describe a quick install. The other sections of this document go into the installation procedure in more detail, but you may find that you do not need this. If you want detailed instruc- tions, skip to the next section. This section describes a basic installation, using a CD-ROM install as an example. o What you need. - The distribution sets (in this example, they are on CD). - One 1.44 MB 3.5" floppy. - A CD-ROM drive (SCSI), a hard disk and a minimum of of mem- ory installed. - The hard disk should have at least + n megabytes of space free, where n is the number of megabytes of main memory in your system. If you wish to install the X Window System as well, you will need at least 215 MB more. o The Quick Installation - Insert the first boot floppy you just created and boot the computer. After language selection, the main menu will be displayed. .***********************************************. * NetBSD-6.0.1 Install System * * * *>a: Install NetBSD to hard disk * * b: Upgrade NetBSD on a hard disk * * c: Re-install sets or install additional sets * * d: Reboot the computer * * e: Utility menu * * f: Config menu * * x: Exit Install System * .***********************************************. - If you wish, you can configure some network settings immedi- ately by choosing the Utility menu and then Configure network. It isn't actually required at this point, but it may be more convenient. Go back to the main menu. - Choose install. - You will be guided through some steps regarding the setup of your disk, and the selection of distributed components to install. When in doubt, refer to the rest of this document for details. - After your disk has been prepared, choose CD-ROM as the medium . The default values for the path and device should be ok. - After all the files have been unpacked, go back to the main menu and select reboot, after you have removed the boot- floppy from the drive. - NetBSD will now boot. If you haven't already done so in sysinst, you should log in as root and set a password for that account. You are also advised to edit /etc/rc.conf to match your needs. - Your installation is now complete. 5. Booting NetBSD Boot your machine. The boot loader will start, and will print a countdown and begin booting. If the boot loader messages do not appear in a reasonable amount of time, you either have a bad boot floppy or a hardware problem. Try writing the install floppy image to a different disk, and using that. It will take a while to load the kernel from the floppy, probably around a minute or so, then, the kernel boot messages will be dis- played. This may take a little while also, as NetBSD will be prob- ing your system to discover which hardware devices are installed. The most important thing to know is that wd0 is NetBSD's name for your first IDE disk, wd1 the second, etc. sd0 is your first SCSI disk, sd1 the second, etc. Note that once the system has finished booting, you need not leave the floppy in the disk drive. Once NetBSD has booted and printed all the boot messages, you will be presented with a welcome message and a main menu. It will also include instructions for using the menus. 6. Network configuration If you do not intend to use networking during the installation, but you do want your machine to be configured for networking once it is installed, you should first go to the Utility menu and select the Configure network option. If you only want to temporarily use net- working during the installation, you can specify these parameters later. If you are not using the Domain Name System (DNS), you can give an empty response when asked to provide a server. 7. Installation drive selection and parameters To start the installation, select Install NetBSD to hard disk from the main menu. The first thing is to identify the disk on which you want to install NetBSD. sysinst will report a list of disks it finds and ask you for your selection. You should see disk names like sd0 or sd1. 8. Selecting which sets to install The next step is to choose which distribution sets you wish to install. Options are provided for full, minimal, and custom instal- lations. If you choose sets on your own, base, etc, and a kernel must be selected. 9. Partitioning the disk o Which portion of the disk to use. You will be asked if you want to use the entire disk or only part of the disk. If you decide to use the entire disk for NetBSD, sysinst will check for the presence of other operating systems and you will be asked to confirm that you want to over- write these. 10. Editing the NetBSD disklabel The partition table of the NetBSD part of a disk is called a disklabel. If your disk already has a disklabel written to it, you can choose Use existing partition sizes. Otherwise, select Set sizes of NetBSD partitions. After you have chosen your partitions and their sizes (or if you opted to use the existing partitions), you will be presented with the layout of the NetBSD disklabel and given one more chance to change it. For each partition, you can set the type, offset and size, block and fragment size, and the mount point. The type that NetBSD uses for normal file storage is called 4.2BSD. A swap parti- tion has a special type called swap. Some partitions in the diskla- bel have a fixed purpose. a Root partition (/) b Swap partition. c The NetBSD portion of the disk. d-h Available for other use. Traditionally, d is the par- tition mounted on /usr, but this is historical prac- tice and not a fixed value. You will then be asked to name your disk's disklabel. The default response will be ok for most purposes. If you choose to name it something different, make sure the name is a single word and con- tains no special characters. You don't need to remember this name. 11. Preparing your hard disk You are now at the point of no return. Nothing has been written to your disk yet, but if you confirm that you want to install NetBSD, your hard drive will be modified. If you are sure you want to pro- ceed, select yes. The install program will now label your disk and make the file sys- tems you specified. The file systems will be initialized to contain NetBSD bootstrapping binaries and configuration files. You will see messages on your screen from the various NetBSD disk preparation tools that are running. There should be no errors in this section of the installation. If there are, restart from the beginning of the installation process. Otherwise, you can continue the installa- tion program after pressing the return key. 12. Getting the distribution sets The NetBSD distribution consists of a number of sets that come in the form of gzipped tarfiles. At this point, you will be presented with a menu which enables you to choose from one of the following methods of installing the sets. Some of these methods will first load the sets on your hard disk, others will extract the sets directly. For all these methods, the first step is making the sets available for extraction, and then do the actual installation. The sets can be made available in a few different ways. The following sections describe each of those methods. After reading the one about the method you will be using, you can continue to the section labeled `Extracting the distribution sets'. 13. Installation from CD-ROM When installing from a CD-ROM, you will be asked to specify the device name for your CD-ROM drive (usually cd0), and the directory name on the CD-ROM where the distribution files are. sysinst will then check if the files are indeed available in the specified location, and proceed to the actual extraction of the sets. 14. Installation using ftp To be able to install using ftp, you first need to configure your network setup if you haven't already done so. sysinst will do this for you, asking you if you want to use DHCP. If you do not use DHCP, you can enter network configuration details yourself. If you do not have DNS set up for the machine that you are installing on, you can just press RETURN in answer to this question, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from, the directory on that host, the account name and password used to log into that host using ftp, and optionally a proxy server to use. If you did not set up DNS, you will need to specify an IP address instead of a hostname for the ftp server. sysinst will proceed to transfer all the default set files from the remote site to your hard disk. 15. Installation using NFS To be able to install using NFS, you first need to configure your network setup if you haven't already done so. sysinst will do this for you, asking you if you want to use DHCP. If you do not use DHCP, you can enter network configuration details yourself. If you do not have DNS set up for the machine that you are installing on, you can just press RETURN in answer to this question, and DNS will not be used. You will also be asked to specify the host that you want to transfer the sets from and the directory on that host that the files are in. This directory should be mountable by the machine you are installing on, i.e., correctly exported to your machine. If you did not set up DNS, you will need to specify an IP address instead of a hostname for the NFS server. 16. Installation from an unmounted file system In order to install from a local file system, you will need to spec- ify the device that the file system resides on (for example sd1e) the type of the file system, and the directory on the specified file system where the sets are located. sysinst will then check if it can indeed access the sets at that location. 17. Installation from a local directory This option assumes that you have already done some preparation yourself. The sets should be located in a directory on a file sys- tem that is already accessible. sysinst will ask you for the name of this directory. 18. Extracting the distribution sets A progress bar will be displayed while the distribution sets are being extracted. After all the files have been extracted, the device node files will be created. If you have already configured networking, you will be asked if you want to use this configuration for normal operation. If so, these values will be installed in the network configuration files. 19. Configure additional items The next menu will allow you to select a number of additional items to configure, including the time zone that you're in, to make sure your clock has the right offset from UTC, the root user's shell, and the initial root password. You can also enable installation of binary packages, which installs the pkgin(1) tool for managing binary packages for third-party soft- ware. This will feel familiar to users of other package tools, such as apt-get or yum. Or, you can install the pkgsrc(7) tree for installing third-party software from source. Finally, you can enable some daemons such as sshd(8), ntpd(8), or mdnsd(8). 20. Finalizing your installation Congratulations, you have successfully installed NetBSD 6.0.1. You can now reboot the machine and boot NetBSD from hard disk. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state. The most important steps are described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the sys- tem asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi- user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). When you have finished editing /etc/rc.conf, type exit at the prompt to leave the single-user shell and continue with the multi-user boot. Other values that may need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute. You may also need to add an ifconfig_int for your network interface, along the lines of ifconfig_le0="inet 192.0.2.123 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_le0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. You should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you installed the X Window System, you may want to read the chap- ter about X in the NetBSD Guide: http://netbsd.org/docs/guide/en/chap-x.html 5. Installing third party packages If you wish to install any of the software freely available for UNIX-like systems you are strongly advised to first check the NetBSD package system, pkgsrc. pkgsrc automatically handles any changes necessary to make the software run on NetBSD. This includes the retrieval and installation of any other packages on which the soft- ware may depend. o More information on the package system is available at http://www.NetBSD.org/docs/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/pkgsrc/current/pkgsrc/README.html o Precompiled binaries can be found at ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/ usually in the emips/6.0.1/All subdir. If you installed pkgin(1) in the sysinst post-installation configuration menu, you can use it to automatically install binary packages over the network. Assuming that /usr/pkg/etc/pkgin/repositories.conf is correctly configured, you can install them with the following commands: # pkgin install tcsh # pkgin install bash # pkgin install perl # pkgin install apache # pkgin install kde # pkgin install firefox ... Note: Some mirror sites don't mirror the /pub/pkgsrc directory. The above commands will install the Tenex-csh and Bourne Again shells, the Perl programming language, Apache web server, KDE desktop environment and the Firefox web browser as well as all the packages they depend on. o If you did not install it from the sysinst post-installation configuration menu, the pkgsrc(7) framework for compiling pack- ages can be obtained by retrieving the file ftp://ftp.NetBSD.org/pub/pkgsrc/pkgsrc.tar.gz. It is typically extracted into /usr/pkgsrc (though other loca- tions work fine) with the commands: # cd /usr # tar -zxpf pkgsrc.tar.gz After extracting, see the doc/pkgsrc.txt file in the extraction directory (e.g., /usr/pkgsrc/doc/pkgsrc.txt) for more informa- tion. 6. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/postfix/main.cf file will almost definitely need to be adjusted. If you prefer a different MTA, then install it using pkgsrc or by hand and adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the man- ual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System The easiest way to upgrade to NetBSD 6.0.1 is with binaries, and that is the method documented here. To do the upgrade, you must have one form of boot media available. You must also have at least the base and kern binary distribution sets avail- able. Finally, you must have sufficient disk space available to install the new binaries. Since files already installed on the system are over- written in place, you only need additional free space for files which weren't previously installed or to account for growth of the sets between releases. If you have a few megabytes free on each of your root (/) and /usr partitions, you should have enough space. Since upgrading involves replacing the kernel, boot blocks, and most of the system binaries, it has the potential to cause data loss. You are strongly advised to back up any important data on the NetBSD partition or on another operating system's partition on your disk before beginning the upgrade process. The upgrade procedure is similar to an installation, but without the hard disk partitioning. sysinst will attempt to merge the settings stored in your /etc directory with the new version of NetBSD. Also, file systems are checked before unpacking the sets. Fetching the binary sets is done in the same manner as the installation procedure; refer to the installa- tion part of the document for help. After a new kernel has been copied to your hard disk, your machine is a complete NetBSD 6.0.1 system. However, that doesn't mean that you're finished with the upgrade process. You will probably want to update the set of device nodes you have in /dev. If you've changed the contents of /dev by hand, you will need to be careful about this, but if not, you can just cd into /dev, and run the command: # sh MAKEDEV all Finally, you will want to delete old binaries that were part of the ver- sion of NetBSD that you upgraded from and have since been removed from the NetBSD distribution. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 6.0.1. Note that sysinst will automatically invoke postinstall fix and thus all issues that are fixed by postinstall by default (see below) will be handled. Issues affecting an upgrade from NetBSD 5.x releases The pthread libraries from previous versions of NetBSD require that the sysctl(3) node kern.no_sa_support be set to 0. This affects the follow- ing environments: o Running a 5.0 kernel with an older userland. o Running an older userland inside a chroot'ed environment on a 5.0 system. o Running older statically linked pthread applications. The 5.0 kernel defaults to 0 for kern.no_sa_support, which covers the first case. However, please note that a full installation of 5.0 (either from scratch or through an upgrade) will set kern.no_sa_support to 1 dur- ing the boot process. This means that for the last two cases, you will have to manually set kern.no_sa_support to 0, using either the sysctl(8) command or through sysctl.conf(5). The implementation of SHA2-HMAC in KAME_IPSEC as used in NetBSD-5 and before did not comply to current standards. FAST_IPSEC does, with the result that old and new systems cannot communicate over IPSEC, if one of the affected authentication algorithms (hmac_sha256, hmac_sha384, hmac_sha512) is used. Issues affecting an upgrade from NetBSD 4.x releases The following issues can generally be resolved by running postinstall with the etc set: postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* - /etc/envsys.conf The following issues need to be resolved manually: o The users `_httpd' and `_timedc' and the groups `_httpd' and `_timedc' need to be created. o Unprivileged use of the mount(8) command now requires the nosuid and nodev options to be explicitly specified. Previ- ously, these options were automatically enforced even if they were not explicitly specified. o A number of things have been removed from the NetBSD 6.0.1 release. See the "Components removed from NetBSD" section near the beginning of this document for a list. Using online NetBSD documentation Documentation is available if you installed the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are o intro(1), o man(1), o apropos(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter # man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter # apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. See http://www.NetBSD.org/mailinglists/ for a web interface. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Bugs also can be submitted and queried with the web interface at http://www.NetBSD.org/support/send-pr.html There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/mailinglists/ If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-users@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their work on BSD systems, support, and encouragement. o The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. o The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. o The Lulea Academic Computer Society for providing the backup services server. o The Columbia University Computer Science Department for hosting the NYC build cluster. o The Western Washington University Computer Science Department for running the WWU build cluster. o The many organizations that provide NetBSD mirror sites. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o We list the individuals and organizations that have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it at http://www.NetBSD.org/donations/ (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to be mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Alan Barrett apb@NetBSD.org Alistair Crooks agc@NetBSD.org Matthew Green mrg@NetBSD.org Chuck Silvers chs@NetBSD.org Matt Thomas matt@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): Reinoud Zandijk reinoud acorn32 Matt Thomas matt alpha Ignatios Souvatzis is amiga Ignatios Souvatzis is amigappc Noriyuki Soda soda arc Julian Coleman jdc atari Matthias Drochner drochner cesfic Erik Berls cyber cobalt Antti Kantee pooka emips Simon Burge simonb evbmips Steve Woodford scw evbppc Izumi Tsutsui tsutsui ews4800mips Izumi Tsutsui tsutsui hp300 Nick Hudson skrll hp700 Valeriy E. Ushakov uwe hpcsh Matt Thomas matt ibmnws Gavan Fantom gavan iyonix Valeriy E. Ushakov uwe landisk Izumi Tsutsui tsutsui luna68k Scott Reynolds scottr mac68k Michael Lorenz macallan macppc Steve Woodford scw mvme68k Steve Woodford scw mvmeppc Matt Thomas matt netwinder Izumi Tsutsui tsutsui news68k Tim Rightnour garbled ofppc Simon Burge simonb pmax Tim Rightnour garbled prep Tim Rightnour garbled rs6000 Tohru Nishimura nisimura sandpoint Simon Burge simonb sbmips Soren Jorvang soren sgimips SAITOH Masanobu msaitoh sh3 Martin Husemann martin sparc64 Anders Magnusson ragge vax NISHIMURA Takeshi nsmrtks x68k Manuel Bouyer bouyer xen The NetBSD 6.0.1 Release Engineering team: Stephen Borrill sborrill@NetBSD.org Manuel Bouyer bouyer@NetBSD.org David Brownlee abs@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Alistair G. Crooks agc@NetBSD.org Havard Eidnes he@NetBSD.org John Heasley heas@NetBSD.org Martin Husemann martin@NetBSD.org Soren Jacobsen snj@NetBSD.org Phil Nelson phil@NetBSD.org Jeremy C. Reed reed@NetBSD.org Jeff Rizzo riz@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Zafer Aydogan zafer@NetBSD.org Christoph Badura bad@NetBSD.org Marc Balmer mbalmer@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Alan Barrett apb@NetBSD.org Grant Beattie grant@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Rafal Boni rafal@NetBSD.org Stephen Borrill sborrill@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org Pavel Cahyna pavel@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Taylor R. Campbell riastradh@NetBSD.org Daniel Carosone dan@NetBSD.org Dave Carrel carrel@NetBSD.org James Chacon jmc@NetBSD.org Mihai Chelaru kefren@NetBSD.org Aleksey Cheusov cheusov@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Marcus Comstedt marcus@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Thomas Cort tcort@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Jed Davis jld@NetBSD.org Matt DeBergalis deberg@NetBSD.org Arnaud Degroote degroote@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Steven Drake sbd@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Havard Eidnes he@NetBSD.org Jaime A Fournier ober@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hauke Fath hauke@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt J. Fleming mjf@NetBSD.org Marty Fouts marty@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Makoto Fujiwara mef@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Brian Ginsbach ginsbach@NetBSD.org Oliver V. Gould ver@NetBSD.org Paul Goyette pgoyette@NetBSD.org Michael Graff explorer@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Ulrich Habel rhaen@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org Adam Hamsik haad@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Yorick Hardy yhardy@NetBSD.org Ben Harris bjh21@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org Emile Heitor imil@NetBSD.org John Heasley heas@NetBSD.org Lars Heidieker para@NetBSD.org Geert Hendrickx ghen@NetBSD.org Rene Hexel rh@NetBSD.org Iain Hibbert plunky@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Adam Hoka ahoka@NetBSD.org Jachym Holecek freza@NetBSD.org David A. Holland dholland@NetBSD.org Christian E. Hopps chopps@NetBSD.org Daniel Horecki morr@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Darran Hunt darran@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hoernquist Astrand lha@NetBSD.org Roland Illig rillig@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Nicolas Joly njoly@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Antti Kantee pooka@NetBSD.org Frank Kardel kardel@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Min Sik Kim minskim@NetBSD.org KIYOHARA Takashi kiyohara@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org Jonathan A. Kollasch jakllsch@NetBSD.org Radoslaw Kujawa rkujawa@NetBSD.org Jochen Kunz jkunz@NetBSD.org Martti Kuparinen martti@NetBSD.org Arnaud Lacombe alc@NetBSD.org Kevin Lahey kml@NetBSD.org David Laight dsl@NetBSD.org Johnny C. Lam jlam@NetBSD.org Guillaume Lasmayous gls@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Tonnerre Lombard tonnerre@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org Anders Magnusson ragge@NetBSD.org John Marino marino@NetBSD.org Roy Marples roy@NetBSD.org Cherry G. Mathew cherry@NetBSD.org David Maxwell david@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Perry Metzger perry@NetBSD.org Luke Mewburn lukem@NetBSD.org Jean-Yves Migeon jym@NetBSD.org Brook Milligan brook@NetBSD.org Minoura Makoto minoura@NetBSD.org Simas Mockevicius symka@NetBSD.org der Mouse mouse@NetBSD.org Constantine A. Murenin cnst@NetBSD.org Joseph Myers jsm@NetBSD.org Tuomo Maekinen tjam@NetBSD.org Zoltan Arnold NAGY zoltan@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Alexander Nasonov alnsn@NetBSD.org Phil Nelson phil@NetBSD.org John Nemeth jnemeth@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Tobias Nygren tnn@NetBSD.org OBATA Akio obache@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Ryo ONODERA ryoon@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Jonathan Perkin sketch@NetBSD.org Fredrik Pettai pettai@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Chris Provenzano proven@NetBSD.org Mindaugas Rasiukevicius rmind@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Jens Rehsack sno@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Tim Rightnour garbled@NetBSD.org Jeff Rizzo riz@NetBSD.org Hans Rosenfeld hans@NetBSD.org Steve Rumble rumble@NetBSD.org Rumko rumko@NetBSD.org Jukka Ruohonen jruoho@NetBSD.org Blair J. Sadewitz bjs@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Silke Scheler silke@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Naoto Shimazaki igy@NetBSD.org Ryo Shimizu ryo@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Daniel Sieger dsieger@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org Joerg Sonnenberger joerg@NetBSD.org Ignatios Souvatzis is@NetBSD.org T K Spindler dogcow@NetBSD.org Matthew Sporleder mspo@NetBSD.org Bill Squier groo@NetBSD.org Adrian Steinmann ast@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org Kimmo Suominen kim@NetBSD.org Gregoire Sutre gsutre@NetBSD.org Sergey Svishchev shattered@NetBSD.org Robert Swindells rjs@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Hasso Tepper hasso@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Mark Weinem weinem@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Frank Wille phx@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Jim Wise jwise@NetBSD.org Colin Wood ender@NetBSD.org Steve Woodford scw@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org David Young dyoung@NetBSD.org Arnaud Ysmal stacktic@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Tim Zingelman tez@NetBSD.org Christos Zoulas christos@NetBSD.org Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trade- marks of their respective owners. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: NetBSD is a registered trademark of The NetBSD Foundation, Inc. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product includes software developed by Intel Corporation and its contributors. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) This product includes cryptographic software written by Eric Young (eay@mincom.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Division, US Naval Research Laboratory. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Hellmuth Michaelis and Joerg Wunsch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Uni- versity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brini. This product includes software developed by Bruce M. Simpson. This product includes software developed by Causality Limited. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Daan Vreeken. This product includes software developed by Daishi Kato This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Dean Huxley. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@min- com.oz.au) This product includes software developed by Eric Young (eay@crypt- soft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by K. Kobayashi. This product includes software developed by K. Kobayashi and H. Shimokawa. This product includes software developed by Ezra Story and by Kari Met- tinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Florian Stoehr. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Garrett D'Amore. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Harvard University and its contributors. This product includes software developed by Harvard University. This product includes software developed by Henrik Vestergaard Draboel. This product includes software developed by Herb Peyerl. This product includes software developed by Hidetoshi Shimokawa. This product includes software developed by Ian W. Dall. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/ This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berke- ley and its contributors. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Lloyd Parkes. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Matthew Fredette. This product includes software developed by Michael Smith. This product includes software developed by Mike Pritchard. This product includes software developed by Mike Pritchard and contribu- tors. This product includes software developed by Minoura Makoto. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Stephan Thesing. This product includes software developed by Steven M. Bellovin. This product includes software developed by Takashi Hamada. This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by TooLs GmbH. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contrib- utors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki. This product includes software developed by Yen Yen Lim and North Dakota State University. This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the Charles D. Cranor, Wash- ington University, University of California, Berkeley and its contribu- tors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) This product includes software developed by the PocketBSD project and its contributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Develop- ment Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia Uni- versity. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the Urbana-Champaign Indepen- dent Media Center. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Labora- tory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Igna- tios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed by Kyma Systems. This product includes software developed for the NetBSD Project by Kyma Systems LLC. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden This product includes software developed for the NetBSD Project by Alle- gro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Labora- tory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Marshall M. Midden. This product includes software developed or owned by Caldera Interna- tional, Inc. The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation. In the following statement, the phrase ``this text'' refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in NetBSD, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html. This notice shall appear on any product containing this material This product includes software contributed to Berkeley by Ralph Campbell. This product includes software contributed to Berkeley by Ralph Campbell and Rick Macklem. This product includes software developed by Jonathan Stone for the NetBSD Project. Some files have the following copyright: Mach Operating System Copyright (c) 1991,1990,1989 Carnegie Mellon University All Rights Reserved. Permission to use, copy, modify and distribute this software and its documentation is hereby granted, provided that both the copy- right notice and this permission notice appear in all copies of the software, derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation. CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. Carnegie Mellon requests users of this software to return to Software Distribution Coordinator or Software.Distribu- tion@CS.CMU.EDU School of Computer Science Carnegie Mellon University Pittsburgh PA 15213-3890 any improvements or extensions that they make and grant Carnegie the rights to redistribute these changes. Some files have the following copyright: Copyright (c) 1994, 1995 Carnegie-Mellon University. All rights reserved. Author: Chris G. Demetriou Permission to use, copy, modify and distribute this software and its documentation is hereby granted, provided that both the copy- right notice and this permission notice appear in all copies of the software, derivative works or modified versions, and any portions thereof, and that both notices appear in supporting documentation. CARNEGIE MELLON ALLOWS FREE USE OF THIS SOFTWARE IN ITS "AS IS" CONDITION. CARNEGIE MELLON DISCLAIMS ANY LIABILITY OF ANY KIND FOR ANY DAMAGES WHATSOEVER RESULTING FROM THE USE OF THIS SOFTWARE. Carnegie Mellon requests users of this software to return to Software Distribution Coordinator or Software.Distribu- tion@CS.CMU.EDU School of Computer Science Carnegie Mellon University Pittsburgh PA 15213-3890 any improvements or extensions that they make and grant Carnegie the rights to redistribute these changes. The End NetBSD August 17, 2012 NetBSD