INSTALL(8) NetBSD System Manager's Manual INSTALL(8) NAME INSTALL -- Installation procedure for NetBSD/sun3. CONTENTS About this Document............................................2 What is NetBSD?................................................2 Changes Between The NetBSD 6.0.5 and 6.0.6 Releases............2 Security Advisory Fixes.....................................3 Other Security Fixes........................................3 Kernel......................................................3 Miscellaneous...............................................4 alpha.......................................................4 sparc64.....................................................4 next68k.....................................................4 The NetBSD Foundation..........................................4 Sources of NetBSD..............................................4 NetBSD 6.0.6 Release Contents..................................4 NetBSD/sun3 subdirectory structure..........................5 Binary distribution sets....................................6 NetBSD/sun3 System Requirements and Supported Devices..........7 Supported hardware..........................................7 Getting the NetBSD System on to Useful Media...................8 Creating boot/install tapes.................................8 Boot/Install from NFS server................................9 Install/Upgrade from CD-ROM.................................9 Install/Upgrade via FTP.....................................9 Preparing your System for NetBSD installation.................10 Installing the NetBSD System..................................10 Installing from tape.......................................10 Installing from NFS........................................11 Installing from SunOS......................................12 Booting the Miniroot.......................................12 Miniroot install program...................................13 Post installation steps.......................................13 Upgrading a previously-installed NetBSD System................15 Compatibility Issues With Previous NetBSD Releases............17 Issues affecting an upgrade from NetBSD 5.x releases.......17 Issues affecting an upgrade from NetBSD 4.x releases.......17 Using online NetBSD documentation.............................18 Administrivia.................................................18 Thanks go to..................................................19 We are........................................................20 Legal Mumbo-Jumbo.............................................25 The End.......................................................30 DESCRIPTION About this Document This document describes the installation procedure for NetBSD 6.0.6 on the sun3 platform. It is available in four different formats titled INSTALL.ext, where .ext is one of .ps, .html, .more, or .txt: .ps PostScript. .html Standard Internet HTML. .more The enhanced text format used on UNIX-like systems by the more(1) and less(1) pager utility programs. This is the format in which the on-line man pages are generally pre- sented. .txt Plain old ASCII. You are reading the ASCII version. What is NetBSD? The NetBSD Operating System is a fully functional Open Source UNIX-like operating system derived from the University of California, Berkeley Net- working Release 2 (Net/2), 4.4BSD-Lite, and 4.4BSD-Lite2 sources. NetBSD runs on 57 different system architectures (ports) across 15 distinct CPU families, and is being ported to more. The NetBSD 6.0.6 release contains complete binary releases for many different system architectures. (A few ports are not fully supported at this time and are thus not part of the binary distribution. Please see the NetBSD web site at http://www.NetBSD.org/ for information on them.) NetBSD is a completely integrated system. In addition to its highly por- table, high performance kernel, NetBSD features a complete set of user utilities, compilers for several languages, the X Window System, firewall software and numerous other tools, all accompanied by full source code. NetBSD is a creation of the members of the Internet community. Without the unique cooperation and coordination the net makes possible, it's likely that NetBSD wouldn't exist. Changes Between The NetBSD 6.0.5 and 6.0.6 Releases NetBSD 6.0.6 is the sixth critical/security update of the NetBSD 6.0 release branch. It represents a selected subset of fixes deemed critical for security or stability reasons. The complete list of changes can be found in the CHANGES-6.0.6: http://ftp.NetBSD.org/pub/NetBSD/NetBSD-6.0.6/CHANGES-6.0.6 file in the top level directory of the NetBSD 6.0.6 release tree. An abbreviated list is as follows: Security Advisory Fixes o NetBSD-SA2014-005: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-005.txt.asc libXfont multiple vulnerabilities o NetBSD-SA2014-006: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-006.txt.asc Multiple OpenSSL vulnerabilities o NetBSD-SA2014-007: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-007.txt.asc bozohttpd basic http authentication bypass o NetBSD-SA2014-008: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-008.txt.asc Multiple OpenSSL vulnerabilities o NetBSD-SA2014-009: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-009.txt.asc Multiple vulnerabilities in the execve system call o NetBSD-SA2014-010: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-010.txt.asc Multiple vulnerabilities in the compatibility layers o NetBSD-SA2014-011: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-011.txt.asc User-controlled memory allocation in the modctl system call o NetBSD-SA2014-012: http://ftp.netbsd.org/pub/NetBSD/security/advisories/NetBSD-SA2014-012.txt.asc Memory leak in the setsockopt system call Advisories prior to NetBSD-SA2014-005 do not affect NetBSD 6.0.6: .: http://www.NetBSD.org/support/security/patches-6.0.6.html Other Security Fixes o Fix various issues in the mount syscall, which could be used by a local user to panic the system. o OpenPAM: Fix incorrect error handling in PAM policy parser. CVE-2014-3879. Kernel o wm(4): Bump max TX DMA size to avoid pathological condition with TSO. o tap(4): Fix a race. PR kern/47506 and kern/46199. o urndis(4): Fix a panic. o vioif(4): Fix a panic. PR kern/49007. o Fix a mbuf leak in IPFilter. o Fix two overflows and a memory corruption bug in ptyfs and umapfs. o Reject unaligned PCI config register ioctl requests before we kassert. Miscellaneous o heimdal: Fix file descriptor leak. Fixes PR lib/48718 o Update to tzdata2014g. o Update bozohttpd to 20140708. o Update openssl to 1.0.1i. o Fix Xserver crash on exit (causing screen palette settings to not be restored) when using wsfb. o postinstall(8): Don't apply "ptyfsoldnodes" if /dev/pts does not exist. o named: Update root.cache to 2014060201. alpha o Make sysinst deal correctly with Tru64 disklabels. PR port- alpha/48697. sparc64 o Fix longjmp bug which causes a segmentation fault on sparc64 kernels with 32-bit userland. next68k o Move physmem calculations before nptpage initialization. PR port- m68k/45915. The NetBSD Foundation The NetBSD Foundation is a tax exempt, not-for-profit 501(c)(3) corpora- tion that devotes itself to the traditional goals and Spirit of the NetBSD Project and owns the trademark of the word ``NetBSD''. It sup- ports the design, development, and adoption of NetBSD worldwide. More information on the NetBSD Foundation, its composition, aims, and work can be found at: http://www.NetBSD.org/foundation/ Sources of NetBSD Refer to http://www.NetBSD.org/mirrors/ NetBSD 6.0.6 Release Contents The root directory of the NetBSD 6.0.6 release is organized as follows: .../NetBSD-6.0.6/ CHANGES Changes between the 5.0 and 6.0 releases. CHANGES-6.0 Changes between the initial 6.0 branch and final release of 6.0. CHANGES-6.0.1 Changes between the 6.0 and 6.0.1 releases. CHANGES-6.0.2 Changes between the 6.0.1 and 6.0.2 releases. CHANGES-6.0.3 Changes between the 6.0.2 and 6.0.3 releases. CHANGES-6.0.4 Changes between the 6.0.3 and 6.0.4 releases. CHANGES-6.0.5 Changes between the 6.0.4 and 6.0.5 releases. CHANGES-6.0.6 Changes between the 6.0.5 and 6.0.6 releases. CHANGES.prev Changes in previous NetBSD releases. LAST_MINUTE Last minute changes and notes about the release. README.files README describing the distribution's contents. source/ Source distribution sets; see below. In addition to the files and directories listed above, there is one directory per architecture, for each of the architectures for which NetBSD 6.0.6 has a binary distribution. The source distribution sets can be found in subdirectories of the source subdirectory of the distribution tree. They contain the complete sources to the system. The source distribution sets are as follows: gnusrc This set contains the ``gnu'' sources, including the source for the compiler, assembler, groff, and the other GNU utilities in the binary distribution sets. sharesrc This set contains the ``share'' sources, which include the sources for the man pages not associated with any particular program; the sources for the typesettable document set; the dictionaries; and more. src This set contains all of the base NetBSD 6.0.6 sources which are not in gnusrc, sharesrc, or syssrc. syssrc This set contains the sources to the NetBSD 6.0.6 kernel for all architectures as well as the config(1) utility. xsrc This set contains the sources to the X Window System. All the above source sets are located in the source/sets subdirectory of the distribution tree. The source sets are distributed as compressed tar files. Except for the pkgsrc set, which is traditionally unpacked into /usr/pkgsrc, all sets may be unpacked into /usr/src with the command: # cd / ; tar -zxpf set_name.tgz In each of the source distribution set directories, there are files which contain the checksums of the files in the directory: MD5 MD5 digests in the format produced by the command: cksum -a MD5 file. SHA512 SHA512 digests in the format produced by the command: cksum -a SHA512 file. The SHA512 digest is safer, but MD5 checksums are provided so that a wider range of operating systems can check the integrity of the release files. NetBSD/sun3 subdirectory structure The sun3-specific portion of the NetBSD 6.0.6 release is found in the sun3 subdirectory of the distribution: .../NetBSD-6.0.6/sun3/. It con- tains the following files and directories: INSTALL.html INSTALL.ps INSTALL.txt INSTALL.more Installation notes in various file formats, including this file. The .more file contains underlined text using the more(1) conventions for indicating italic and bold display. binary/ kernel/ netbsd-GENERIC.gz A gzipped NetBSD kernel containing code for everything supported in this release. sets/ sun3 binary distribution sets; see below. installation/ miniroot/ sun3 miniroot file system image; see below. misc/ Miscellaneous sun3 installation utilities; see installation section below. netboot/ Two programs needed to boot sun3 kernels over the network. tapeimage/ Tape boot programs, and a RAMDISK kernel. Binary distribution sets The NetBSD sun3 binary distribution sets contain the binaries which com- prise the NetBSD 6.0.6 release for sun3. The binary distribution sets can be found in the sun3/binary/sets subdirectory of the NetBSD 6.0.6 distribution tree, and are as follows: base The NetBSD 6.0.6 sun3 base binary distribution. You must install this distribution set. It contains the base NetBSD utilities that are necessary for the system to run and be mini- mally functional. comp Things needed for compiling programs. This set includes the system include files (/usr/include) and the various system libraries (except the shared libraries, which are included as part of the base set). This set also includes the manual pages for all of the utilities it contains, as well as the system call and library manual pages. etc This distribution set contains the system configuration files that reside in /etc and in several other places. This set must be installed if you are installing the system from scratch, but should not be used if you are upgrading. games This set includes the games and their manual pages. kern-GENERIC This set contains a NetBSD/sun3 6.0.6 GENERIC kernel, named /netbsd. You must install this distribution set. man This set includes all of the manual pages for the binaries and other software contained in the base set. Note that it does not include any of the manual pages that are included in the other sets. misc This set includes the system dictionaries, the typesettable doc- ument set, and other files from /usr/share. text This set includes NetBSD's text processing tools, including groff(1), all related programs, and their manual pages. NetBSD maintains its own set of sources for the X Window System in order to assure tight integration and compatibility. These sources are based on XFree86 4.5.0. Binary sets for the X Window System are distributed with NetBSD. The sets are: xbase The basic files needed for a complete X client environment. This does not include the X servers. xcomp The extra libraries and include files needed to compile X source code. xfont Fonts needed by the X server and by X clients. xetc Configuration files for X which could be locally modified. xserver The X server. The sun3 binary distribution sets are distributed as gzipped tar files named with the extension .tgz, e.g. base.tgz. The instructions given for extracting the source sets work equally well for the binary sets, but it is worth noting that if you use that method, the filenames stored in the sets are relative and therefore the files are extracted below the current directory. Therefore, if you want to extract the binaries into your system, i.e. replace the system binaries with them, you have to run the tar -xzpf command from the root directory ( / ) of your system. There is a collection of Sun3 and Sun3X kernels in the sun3/binary/kernels subdirectory of the NetBSD 6.0.6 distribution. The ones named netbsd-ramdisk*.gz contain a root file system image and should only be used for the initial installation. The others are included for convenience. (Most people will want to use netbsd-generic.gz or netbsd-generic3x.gz as appropriate.) Please note that these kernels are simply gzipped and are not tar archives. Note: Each directory in the sun3 binary distribution also has its own checksum files, just as the source distribution does. NetBSD/sun3 System Requirements and Supported Devices NetBSD/sun3 6.0.6 runs on most Sun3 machines, including: 3/50 3/60 3/110 3/75 3/150 3/160 3/260 3/280 3/E 3/80 3/470 Note that NetBSD/sun3 includes support for `Sun3X' machines, which used to be supported with a separate NetBSD/sun3x distribution. The minimal configuration requires 4 MB of RAM and about 100 MB of disk space. To install the entire system requires much more disk space. To run X or compile the system, more RAM is recommended. Good performance requires 8 MB of RAM, or 16 MB when running the X Window System. A good rule of thumb is to have a swap partition twice the size of the amount of RAM in your machine. You will probably want to compile your own kernel, as GENERIC is large and bulky to accommodate all people. Note that the sun3 installation procedure uses a miniroot image which is placed into the swap area of the disk. The swap partition must be at least as large as the miniroot image (10 MB). Supported hardware o Serial ports (RS232) - built-in ttya, ttyb o Video adapters - bwtwo - cgtwo - cgfour o Network interfaces: - On-board Lance Ethernet - On-board or VME Intel Ethernet - Sun3/E SCSI/Ethernet board o SCSI - Most SCSI disks, tapes, CD-ROMs, etc - On-board Sun3/80 SCSI (esp) - On-board SCSI-3 (si) - VME SCSI-3 board (si) - Sun3/E SCSI/Ethernet board o SMD Disks - Xylogics 450/451 - Xylogics 753/7053 o Input devices - Sun keyboard and mouse o Miscellaneous - Battery-backed real-time clock. - On-board floppy controller (Sun3/80 floppy) If it's not on this list, there is no support for it in this release. Getting the NetBSD System on to Useful Media Installation is supported from several media types, including: o Tape o NFS o CD-ROM o FTP Note: Installing on a `bare' machine requires some bootable device; either a tape drive or Sun-compatible NFS server. The procedure for transferring the distribution sets onto installation media depends on the type of media. Instructions for each type of media are given below. In order to create installation media, you will need all the files in the directory .../NetBSD-6.0.6/sun3/ Creating boot/install tapes Installing from tape is the simplest method of all. This method uses two tapes; one called the boot tape, and another called the install tape. The boot tape is created as follows: # cd .../NetBSD-6.0.6/sun3/installation/tapeimage # sh MakeBootTape /dev/nrst0 The install tape is created as follows: # cd .../NetBSD-6.0.6/sun3/installation/tapeimage # sh MakeInstallTape /dev/nrst0 If the tapes do not work as expected, you may need to explicitly set the EOF mark at the end of each tape segment. It may also be necessary to use the conv=osync argument to dd(1). Note that this argument is incom- patible with the bs= argument. Consult the tape-related manual pages on the system where the tapes are created for more details. Boot/Install from NFS server If your machine has a disk and network connection, but no tape drive, it may be convenient for you to install NetBSD over the network. This involves temporarily booting your machine over NFS, just long enough so you can initialize its disk. This method requires that you have access to an NFS server on your network so you can configure it to support disk- less boot for your machine. Configuring the NFS server is normally a task for a system administrator, and is not trivial. If you are using a NetBSD system as the boot-server, have a look at the diskless(8) manual page for guidelines on how to proceed with this. If the server runs another operating system, consult the documentation that came with it (i.e. add_client(8) on SunOS). When instructed to boot over the network, your sun3 expects to be able to download a second stage bootstrap program via TFTP after it has acquired its IP address through RARP. It will attempt to download a file using a name derived from the machine's recently acquired IP address, and in the case of sun3x machines, an extension which corresponds to the machine architecture. (It may be handy to have a hexadecimal calculator for this next step.) The filename is created by converting the machine's assigned IP address into hexadecimal, most-significant octet first, using upper- case characters for the non-decimal (A-F) digits. sun3x machines use a filename suffix of .SUN3X. For example, a sun3 which has been assigned IP address 130.115.144.11 will make an TFTP request for 8273900B, and a sun3x will try 8273900B.SUN3X. Normally, this file is a symbolic link to the NetBSD/sun3 netboot program, which should be located in a place where the TFTP daemon can find it. (Remember, many TFTP daemons run in a chroot'ed environment.) The netboot program may be found in the install directory of this distribution. The netboot program will query a bootparamd server to find the NFS server address and path name for its root, and then load a kernel from that location. The server should have a copy of the netbsd-rd kernel in the root area for your client (no other files are needed in the client root) and /etc/bootparams on the server should have an entry for your client and its root directory. The client will need access to the miniroot image, which can be provided using NFS or remote shell. If you will be installing NetBSD on several clients, it may be useful to know that you can use a single NFS root for all the clients as long as they only use the netbsd-rd kernel. There will be no conflict between clients because the RAM-disk kernel will not use the NFS root. No swap file is needed; the RAM-disk kernel does not use that either. Install/Upgrade from CD-ROM This method requires that you boot from another device (i.e. tape or net- work, as described above). You may need to make a boot tape on another machine using the files provided on the CD-ROM. Once you have booted netbsd-rd (the RAM-disk kernel) and loaded the miniroot, you can load any of the distribution sets directly from the CD-ROM. The install program in the miniroot automates the work required to mount the CD-ROM and extract the files. Install/Upgrade via FTP This method requires that you boot from another device (i.e. tape or net- work, as described above). You may need to make a boot tape on another machine using the files in .../install (which you get via FTP). Once you have booted netbsd-rd (the RAM-disk kernel) and loaded the miniroot, you can load any of the distribution sets over the net using FTP. The install program in the miniroot automates the work required to configure the network interface and transfer the files. The preparations for this installation/upgrade method are easy; all you make sure that there's some FTP site from which you can retrieve the NetBSD distribution when you're about to install or upgrade. You need to know the numeric IP address of that site, and, if it's not on a network directly connected to the machine on which you're installing or upgrading NetBSD, you need to know the numeric IP address of the router closest to the NetBSD machine. Finally, you need to know the numeric IP address of the NetBSD machine itself. Preparing your System for NetBSD installation Sun3 machines usually need little or no preparation before installing NetBSD, other than the usual, well advised precaution of backing up all data on any attached storage devices. You will need to know the SCSI target ID of the drive on which you will install NetBSD. Note: SunOS on the sun3 uses confusing names for the SCSI devices: tar- get 1 is sd2, target 2 is sd4, etc. It might be a good time to run the diagnostics on your Sun3. First, attach a terminal to the ttya serial port, then set the ``Diag/Norm'' switch to the Diagnostic position, and power-on the machine. The Diag. switch setting forces console interaction to occur on ttya. Note that the 3/80 has a ``software'' diag switch you can set at the PROM monitor prompt. To turn on diag boot mode, do: q 70b 12 To return to normal boot mode, do: q 70b 6. The console location (ttya, ttyb, or keyboard/display) is controlled by address 0x1F in the EEPROM, which you can examine and change in the PROM monitor by entering q1f followed by a numeric value (or just a `.' if you don't want to change it). Console values are: 00 Default graphics display 10 tty a (9600-N-8-1) 11 tty b (1200-N-8-1) 20 Color option board on P4 Installing the NetBSD System Installing NetBSD is a relatively complex process, but if you have this document in hand it should not be too difficult. There are several ways to install NetBSD onto your disk. If your machine has a tape drive the easiest way is Installing from tape (details below). If your machine is on a network with a suitable NFS server, then Installing from NFS is the next best method. Otherwise, if you have another Sun machine running SunOS you can initialize the disk on that machine and then move the disk. (Installing from SunOS is not recom- mended.) Installing from tape Create the NetBSD/sun3 6.0.6 boot tape as described in the section enti- tled Preparing a boot tape and boot the tape. At the PROM monitor prompt, use one of the commands: >b st() >b st(0,8,0) The first example will use the tape on SCSI target 4, where the second will use SCSI target 5. The > is the monitor prompt. After the tape loads, you should see many lines of configuration mes- sages, and then the following `welcome' screen: Welcome to the NetBSD/sun3 RAMDISK root! This environment is designed to do only three things: 1: Partition your disk (use the command: edlabel /dev/rsd0c) 2: Copy a miniroot image into the swap partition (/dev/rsd0b) 3: Reboot (using the swap partition, i.e. /dev/sd?b). Note that the sun3 firmware cannot boot from a partition located more than 1 GB from the beginning of the disk, so the swap partition should be completely below the 1 GB boundary. Copying the miniroot can be done several ways, allowing the source of the miniroot image to be on any of these: boot tape, NFS server, TFTP server, rsh server The easiest is loading from tape, which is done as follows: mt -f /dev/nrst0 rewind mt -f /dev/nrst0 fsf 2 dd if=/dev/nrst0 of=/dev/rsd0b bs=32k conv=sync (For help with other methods, please see the install notes.) To reboot using the swap partition, first use "halt", then at the PROM monitor prompt use a command like: b sd(,,1) -s To view this message again, type: cat /.welcome Copy the miniroot as described in the welcome message, and reboot from that just installed miniroot. See the section entitled Booting the miniroot for details. Installing from NFS Before you can install from NFS, you must have already configured your NFS server to support your machine as a diskless client. Instructions for configuring the server are found in the section entitled Getting the NetBSD System onto Useful Media above. First, at the Sun PROM monitor prompt, enter a boot command using the network interface as the boot device. On desktop machines this is le, and ie on the others. Examples: >b le() -s >b ie() -s After the boot program loads the RAMDISK kernel, you should see the wel- come screen as shown in the Installing from tape section above. You must configure the network interface before you can use any network resources. For example the command: ssh> ifconfig le0 inet 192.233.20.198 up will bring up the network interface with that address. The next step is to copy the miniroot from your server. This can be done using either NFS or remote shell. (In the examples that follow, the server has IP address 192.233.20.195.) You may then need to add a default route if the server is on a different subnet: ssh> route add default 192.233.20.255 1 You can look at the route table using: ssh> route show Now mount the NFS file system containing the miniroot image: ssh> mount -r 192.233.20.195:/server/path /mnt The procedure is simpler if you have space for an expanded (not com- pressed) copy of the miniroot image. In that case: ssh> dd if=/mnt/miniroot.fs of=/dev/rsd0b bs=8k Otherwise, you will need to use zcat to expand the miniroot image while copying. This is tricky because the ssh program (small shell) does not handle sh(1) pipeline syntax. Instead, you first run the reader in the background with its input set to /dev/pipe and then run the other program in the foreground with its output to /dev/pipe. The result looks like this: ssh> run -bg dd if=/dev/pipe of=/dev/rsd0b obs=8k ssh> run -o /dev/pipe zcat /mnt/install/miniroot.fs.gz To load the miniroot using rsh to the server, you would use a pair of commands similar to the above. Here is another example: ssh> run -b dd if=/dev/pipe of=/dev/rsd0b obs=8k ssh> run -o /dev/pipe rsh 192.233.20.195 zcat miniroot.fs.gz Installing from SunOS To install NetBSD/sun3 onto a machine already running SunOS, you will need the miniroot image (miniroot.fs.gz) and some means to decompress it. First, boot SunOS and place the miniroot file onto the hard drive. If you do not have gzip for SunOS, you will need to decompress the image elsewhere before you can use it. Next, bring SunOS down to single user mode to insure that nothing will be using the swap space on your drive. To be extra safe, reboot the machine into single-user mode rather than using the shutdown command. Now copy the miniroot image onto your swap device (here /dev/rsd0b) with the command gzip -dc miniroot.fs.gz | dd of=/dev/rsd0b obs=32k or if you have already decompressed the miniroot dd if=miniroot.fs of=/dev/rsd0b obs=32k Finally, reboot the machine and instruct the ROM to boot from the swap device as described in the next section. Booting the Miniroot If the miniroot was installed on partition `b' of the disk with SCSI tar- get ID=0 then the PROM boot command would be: >b sd(0,0,1) -s With SCSI target ID=2, the PROM is: >b sd(0,10,1) -s The numbers in parentheses above are: 1. controller (usually zero) 2. unit number (SCSI-ID * 8, in hexadecimal) 3. partition number Miniroot install program The miniroot's install program is very simple to use. It will guide you through the entire process, and is well automated. Additional improve- ments are planned for future releases. The miniroot's install program will: o Allow you to place disklabels on additional disks. The disk we are installing on should already have been partitioned using the RAMDISK kernel. o Create file systems on target partitions. o Allow you to set up your system's network configuration. Remember to specify host names without the domain name appended to the end. For example use foo instead of foo.bar.org. If, during the process of configuring the network interfaces, you make a mistake, you will be able to re-configure that interface by simply selecting it for configuration again. o Mount target file systems. You will be given the opportunity to manually edit the resulting /etc/fstab. o Extract binary sets from the media of your choice. o Copy configuration information gathered during the installation process to your root file system (/). o Make device nodes in your root file system under /dev. o Copy a new kernel onto your root partition (/). o Install a new boot block. o Check your file systems for integrity. First-time installation on a system through a method other than the installation program is possible, but strongly discouraged. Post installation steps Once you've got the operating system running, there are a few things you need to do in order to bring the system into a properly configured state. The most important steps are described below. 1. Configuring /etc/rc.conf If you or the installation software haven't done any configuration of /etc/rc.conf (sysinst usually will), the system will drop you into single user mode on first reboot with the message /etc/rc.conf is not configured. Multiuser boot aborted. and with the root file system (/) mounted read-only. When the sys- tem asks you to choose a shell, simply press RETURN to get to a /bin/sh prompt. If you are asked for a terminal type, respond with vt220 (or whatever is appropriate for your terminal type) and press RETURN. You may need to type one of the following commands to get your delete key to work properly, depending on your keyboard: # stty erase '^h' # stty erase '^?' At this point, you need to configure at least one file in the /etc directory. You will need to mount your root file system read/write with: # /sbin/mount -u -w / Change to the /etc directory and take a look at the /etc/rc.conf file. Modify it to your tastes, making sure that you set rc_configured=YES so that your changes will be enabled and a multi- user boot can proceed. Default values for the various programs can be found in /etc/defaults/rc.conf, where some in-line documentation may be found. More complete documentation can be found in rc.conf(5). When you have finished editing /etc/rc.conf, type exit at the prompt to leave the single-user shell and continue with the multi-user boot. Other values that may need to be set in /etc/rc.conf for a networked environment are hostname and possibly defaultroute. You may also need to add an ifconfig_int for your network interface, along the lines of ifconfig_le0="inet 192.0.2.123 netmask 255.255.255.0" or, if you have myname.my.dom in /etc/hosts: ifconfig_le0="inet myname.my.dom netmask 255.255.255.0" To enable proper hostname resolution, you will also want to add an /etc/resolv.conf file or (if you are feeling a little more adventur- ous) run named(8). See resolv.conf(5) or named(8) for more informa- tion. Instead of manually configuring network and naming service, DHCP can be used by setting dhclient=YES in /etc/rc.conf. Other files in /etc that may require modification or setting up include /etc/mailer.conf, /etc/nsswitch.conf, and /etc/wscons.conf. 2. Logging in After reboot, you can log in as root at the login prompt. Unless you've set a password in sysinst, there is no initial password. You should create an account for yourself (see below) and protect it and the ``root'' account with good passwords. By default, root login from the network is disabled (even via ssh(1)). One way to become root over the network is to log in as a different user that belongs to group ``wheel'' (see group(5)) and use su(1) to become root. 3. Adding accounts Use the useradd(8) command to add accounts to your system. Do not edit /etc/passwd directly! See vipw(8) and pwd_mkdb(8) if you want to edit the password database. 4. The X Window System If you installed the X Window System, you may want to read the chap- ter about X in the NetBSD Guide: http://netbsd.org/docs/guide/en/chap-x.html 5. Installing third party packages If you wish to install any of the software freely available for UNIX-like systems you are strongly advised to first check the NetBSD package system, pkgsrc. pkgsrc automatically handles any changes necessary to make the software run on NetBSD. This includes the retrieval and installation of any other packages on which the soft- ware may depend. o More information on the package system is available at http://www.NetBSD.org/docs/software/packages.html o A list of available packages suitable for browsing is at ftp://ftp.NetBSD.org/pub/pkgsrc/current/pkgsrc/README.html o Precompiled binaries can be found at ftp://ftp.NetBSD.org/pub/pkgsrc/packages/NetBSD/ usually in the sun3/6.0.6/All subdir. If you installed pkgin(1) in the sysinst post-installation configuration menu, you can use it to automatically install binary packages over the network. Assuming that /usr/pkg/etc/pkgin/repositories.conf is correctly configured, you can install them with the following commands: # pkgin install tcsh # pkgin install bash # pkgin install perl # pkgin install apache # pkgin install kde # pkgin install firefox ... Note: Some mirror sites don't mirror the /pub/pkgsrc directory. The above commands will install the Tenex-csh and Bourne Again shells, the Perl programming language, Apache web server, KDE desktop environment and the Firefox web browser as well as all the packages they depend on. o If you did not install it from the sysinst post-installation configuration menu, the pkgsrc(7) framework for compiling pack- ages can be obtained by retrieving the file ftp://ftp.NetBSD.org/pub/pkgsrc/pkgsrc.tar.gz. It is typically extracted into /usr/pkgsrc (though other loca- tions work fine) with the commands: # cd /usr # tar -zxpf pkgsrc.tar.gz After extracting, see the doc/pkgsrc.txt file in the extraction directory (e.g., /usr/pkgsrc/doc/pkgsrc.txt) for more informa- tion. 6. Misc o Edit /etc/mail/aliases to forward root mail to the right place. Don't forget to run newaliases(1) afterwards. o The /etc/postfix/main.cf file will almost definitely need to be adjusted. If you prefer a different MTA, then install it using pkgsrc or by hand and adjust /etc/mailer.conf. o Edit /etc/rc.local to run any local daemons you use. o Many of the /etc files are documented in section 5 of the man- ual; so just invoking # man 5 filename is likely to give you more information on these files. Upgrading a previously-installed NetBSD System It is possible to easily upgrade your existing NetBSD/sun3 system using the upgrade program in the miniroot. If you wish to upgrade your system by this method, simply select the upgrade option once the miniroot has booted. The upgrade program with then guide you through the procedure. The upgrade program will: o Enable the network based on your system's current network con- figuration. o Mount your existing file systems. o Extract binary sets from the media of your choice. o Make new device nodes in your root file system under /dev. o Copy a new kernel onto your root partition (/). Note: the existing kernel will not be backed up; doing so would be pointless, since older kernels may not be capa- ble of running NetBSD 6.0.6 executables. o Install a new boot block. o Check your file systems for integrity. Using the miniroot's upgrade program is the preferred method of upgrading your system. However, it is possible to upgrade your system manually. To do this, follow the following procedure: o Place at least the base binary set in a file system accessible to the target machine. A local file system is preferred, since the NFS subsystem in the NetBSD 6.0.6 kernel may be incompati- ble with your old binaries. o Back up your pre-existing kernel and copy the 6.0.6 kernel into your root partition (/). o Reboot with the 6.0.6 kernel into single-user mode. (Otherwise you can not install the boot block.) o Check all file systems: # /sbin/fsck -pf o Mount all local file systems: # /sbin/mount -a -t nonfs o If you keep /usr or /usr/share on an NFS server, you will want to mount those file systems as well. To do this, you will need to enable the network: # sh /etc/rc.d/network start o Make sure you are in the root file system (/ and extract the) base binary set: # cd / # pax -zrvpe -f Ar /path/to/base.tgz o Install a new boot block: (assuming root is on /dev/rsd0a) # cd /usr/mdec # cp -p ./ufsboot /mnt/ufsboot # sync ; sleep 1 ; sync # /usr/sbin/installboot -v /dev/rsd0a bootxx /ufsboot o Sync the file systems: sync o At this point you may extract any other binary sets you may have placed on local file systems, or you may wish to extract additional sets at a later time. To extract these sets, use the following commands: # cd / # pax -zrvpe -f path_to_set Note: You should not extract the etc set if upgrading. Instead, you should extract that set into another area and carefully merge the changes by hand. Compatibility Issues With Previous NetBSD Releases Users upgrading from previous versions of NetBSD may wish to bear the following problems and compatibility issues in mind when upgrading to NetBSD 6.0.6. Note that sysinst will automatically invoke postinstall fix and thus all issues that are fixed by postinstall by default (see below) will be handled. Issues affecting an upgrade from NetBSD 5.x releases The pthread libraries from previous versions of NetBSD require that the sysctl(3) node kern.no_sa_support be set to 0. This affects the follow- ing environments: o Running a 5.0 kernel with an older userland. o Running an older userland inside a chroot'ed environment on a 5.0 system. o Running older statically linked pthread applications. The 5.0 kernel defaults to 0 for kern.no_sa_support, which covers the first case. However, please note that a full installation of 5.0 (either from scratch or through an upgrade) will set kern.no_sa_support to 1 dur- ing the boot process. This means that for the last two cases, you will have to manually set kern.no_sa_support to 0, using either the sysctl(8) command or through sysctl.conf(5). The implementation of SHA2-HMAC in KAME_IPSEC as used in NetBSD-5 and before did not comply to current standards. FAST_IPSEC does, with the result that old and new systems cannot communicate over IPSEC, if one of the affected authentication algorithms (hmac_sha256, hmac_sha384, hmac_sha512) is used. Issues affecting an upgrade from NetBSD 4.x releases The following issues can generally be resolved by running postinstall with the etc set: postinstall -s /path/to/etc.tgz check postinstall -s /path/to/etc.tgz fix Issues fixed by postinstall: o Various files in /etc need upgrading. These include: - /etc/defaults/* - /etc/mtree/* - /etc/daily - /etc/weekly - /etc/monthly - /etc/security - /etc/rc.subr - /etc/rc - /etc/rc.shutdown - /etc/rc.d/* - /etc/envsys.conf The following issues need to be resolved manually: o The users `_httpd' and `_timedc' and the groups `_httpd' and `_timedc' need to be created. o Unprivileged use of the mount(8) command now requires the nosuid and nodev options to be explicitly specified. Previ- ously, these options were automatically enforced even if they were not explicitly specified. o A number of things have been removed from the NetBSD 6.0.6 release. See the "Components removed from NetBSD" section near the beginning of this document for a list. Using online NetBSD documentation Documentation is available if you installed the manual distribution set. Traditionally, the ``man pages'' (documentation) are denoted by `name(section)'. Some examples of this are o intro(1), o man(1), o apropos(1), o passwd(1), and o passwd(5). The section numbers group the topics into several categories, but three are of primary interest: user commands are in section 1, file formats are in section 5, and administrative information is in section 8. The man command is used to view the documentation on a topic, and is started by entering man [section] topic. The brackets [] around the sec- tion should not be entered, but rather indicate that the section is optional. If you don't ask for a particular section, the topic with the lowest numbered section name will be displayed. For instance, after log- ging in, enter # man passwd to read the documentation for passwd(1). To view the documentation for passwd(5), enter # man 5 passwd instead. If you are unsure of what man page you are looking for, enter # apropos subject-word where subject-word is your topic of interest; a list of possibly related man pages will be displayed. Administrivia If you've got something to say, do so! We'd like your input. There are various mailing lists available via the mailing list server at majordomo@NetBSD.org. To get help on using the mailing list server, send mail to that address with an empty body, and it will reply with instruc- tions. See http://www.NetBSD.org/mailinglists/ for a web interface. There are various mailing lists set up to deal with comments and ques- tions about this release. Please send comments to: netbsd-comments@NetBSD.org. To report bugs, use the send-pr(1) command shipped with NetBSD, and fill in as much information about the problem as you can. Good bug reports include lots of details. Bugs also can be submitted and queried with the web interface at http://www.NetBSD.org/support/send-pr.html There are also port-specific mailing lists, to discuss aspects of each port of NetBSD. Use majordomo to find their addresses, or visit http://www.NetBSD.org/mailinglists/ If you're interested in doing a serious amount of work on a specific port, you probably should contact the `owner' of that port (listed below). If you'd like to help with this effort, and have an idea as to how you could be useful, send us mail or subscribe to: netbsd-users@NetBSD.org. As a favor, please avoid mailing huge documents or files to these mailing lists. Instead, put the material you would have sent up for FTP or WWW somewhere, then mail the appropriate list about it, or, if you'd rather not do that, mail the list saying you'll send the data to those who want it. Thanks go to o The former members of UCB's Computer Systems Research Group, includ- ing (but not limited to): Keith Bostic Ralph Campbell Mike Karels Marshall Kirk McKusick for their work on BSD systems, support, and encouragement. o The Internet Systems Consortium, Inc. for hosting the NetBSD FTP, CVS, AnonCVS, mail, mail archive, GNATS, SUP, Rsync and WWW servers. o The Internet Research Institute in Japan for hosting the server which runs the CVSweb interface to the NetBSD source tree. o The Lulea Academic Computer Society for providing the backup services server. o The Columbia University Computer Science Department for hosting the NYC build cluster. o The Western Washington University Computer Science Department for running the WWU build cluster. o The many organizations that provide NetBSD mirror sites. o Without CVS, this project would be impossible to manage, so our hats go off to Brian Berliner, Jeff Polk, and the various other people who've had a hand in making CVS a useful tool. o We list the individuals and organizations that have made donations or loans of hardware and/or money, to support NetBSD development, and deserve credit for it at http://www.NetBSD.org/donations/ (If you're not on that list and should be, tell us! We probably were not able to get in touch with you, to verify that you wanted to be listed.) o Finally, we thank all of the people who've put sweat and tears into developing NetBSD since its inception in January, 1993. (Obviously, there are a lot more people who deserve thanks here. If you're one of them, and would like to be mentioned, tell us!) We are... (in alphabetical order) The NetBSD core group: Alan Barrett apb@NetBSD.org Alistair Crooks agc@NetBSD.org Matthew Green mrg@NetBSD.org Chuck Silvers chs@NetBSD.org Matt Thomas matt@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Christos Zoulas christos@NetBSD.org The portmasters (and their ports): Reinoud Zandijk reinoud acorn32 Matt Thomas matt alpha Ignatios Souvatzis is amiga Ignatios Souvatzis is amigappc Noriyuki Soda soda arc Julian Coleman jdc atari Matthias Drochner drochner cesfic Erik Berls cyber cobalt Antti Kantee pooka emips Simon Burge simonb evbmips Steve Woodford scw evbppc Izumi Tsutsui tsutsui ews4800mips Izumi Tsutsui tsutsui hp300 Nick Hudson skrll hp700 Valeriy E. Ushakov uwe hpcsh Matt Thomas matt ibmnws Gavan Fantom gavan iyonix Valeriy E. Ushakov uwe landisk Izumi Tsutsui tsutsui luna68k Scott Reynolds scottr mac68k Michael Lorenz macallan macppc Steve Woodford scw mvme68k Steve Woodford scw mvmeppc Matt Thomas matt netwinder Izumi Tsutsui tsutsui news68k Tim Rightnour garbled ofppc Simon Burge simonb pmax Tim Rightnour garbled prep Tim Rightnour garbled rs6000 Tohru Nishimura nisimura sandpoint Simon Burge simonb sbmips Soren Jorvang soren sgimips SAITOH Masanobu msaitoh sh3 Martin Husemann martin sparc64 Anders Magnusson ragge vax NISHIMURA Takeshi nsmrtks x68k Manuel Bouyer bouyer xen The NetBSD 6.0.6 Release Engineering team: Stephen Borrill sborrill@NetBSD.org Manuel Bouyer bouyer@NetBSD.org David Brownlee abs@NetBSD.org James Chacon jmc@NetBSD.org Julian Coleman jdc@NetBSD.org Alistair G. Crooks agc@NetBSD.org Havard Eidnes he@NetBSD.org John Heasley heas@NetBSD.org Martin Husemann martin@NetBSD.org Soren Jacobsen snj@NetBSD.org Phil Nelson phil@NetBSD.org Jeremy C. Reed reed@NetBSD.org Jeff Rizzo riz@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org NetBSD Developers: Nathan Ahlstrom nra@NetBSD.org Steve Allen wormey@NetBSD.org Jukka Andberg jandberg@NetBSD.org Julian Assange proff@NetBSD.org Lennart Augustsson augustss@NetBSD.org Zafer Aydogan zafer@NetBSD.org Christoph Badura bad@NetBSD.org Marc Balmer mbalmer@NetBSD.org Bang Jun-Young junyoung@NetBSD.org Dieter Baron dillo@NetBSD.org Robert V. Baron rvb@NetBSD.org Alan Barrett apb@NetBSD.org Grant Beattie grant@NetBSD.org Erik Berls cyber@NetBSD.org Hiroyuki Bessho bsh@NetBSD.org John Birrell jb@NetBSD.org Rafal Boni rafal@NetBSD.org Stephen Borrill sborrill@NetBSD.org Sean Boudreau seanb@NetBSD.org Manuel Bouyer bouyer@NetBSD.org Allen Briggs briggs@NetBSD.org Mark Brinicombe mark@NetBSD.org Aaron Brown abrown@NetBSD.org Andrew Brown atatat@NetBSD.org David Brownlee abs@NetBSD.org Jon Buller jonb@NetBSD.org Simon Burge simonb@NetBSD.org Robert Byrnes byrnes@NetBSD.org Pavel Cahyna pavel@NetBSD.org D'Arcy J.M. Cain darcy@NetBSD.org Taylor R. Campbell riastradh@NetBSD.org Daniel Carosone dan@NetBSD.org Dave Carrel carrel@NetBSD.org James Chacon jmc@NetBSD.org Mihai Chelaru kefren@NetBSD.org Aleksey Cheusov cheusov@NetBSD.org Bill Coldwell billc@NetBSD.org Julian Coleman jdc@NetBSD.org Marcus Comstedt marcus@NetBSD.org Jeremy Cooper jeremy@NetBSD.org Thomas Cort tcort@NetBSD.org Chuck Cranor chuck@NetBSD.org Alistair Crooks agc@NetBSD.org Johan Danielsson joda@NetBSD.org John Darrow jdarrow@NetBSD.org Jed Davis jld@NetBSD.org Matt DeBergalis deberg@NetBSD.org Arnaud Degroote degroote@NetBSD.org Rob Deker deker@NetBSD.org Chris G. Demetriou cgd@NetBSD.org Tracy Di Marco White gendalia@NetBSD.org Jaromir Dolecek jdolecek@NetBSD.org Andy Doran ad@NetBSD.org Roland Dowdeswell elric@NetBSD.org Steven Drake sbd@NetBSD.org Emmanuel Dreyfus manu@NetBSD.org Matthias Drochner drochner@NetBSD.org Jun Ebihara jun@NetBSD.org Havard Eidnes he@NetBSD.org Jaime A Fournier ober@NetBSD.org Stoned Elipot seb@NetBSD.org Michael van Elst mlelstv@NetBSD.org Enami Tsugutomo enami@NetBSD.org Bernd Ernesti veego@NetBSD.org Erik Fair fair@NetBSD.org Gavan Fantom gavan@NetBSD.org Hauke Fath hauke@NetBSD.org Hubert Feyrer hubertf@NetBSD.org Jason R. Fink jrf@NetBSD.org Matt J. Fleming mjf@NetBSD.org Marty Fouts marty@NetBSD.org Liam J. Foy liamjfoy@NetBSD.org Matt Fredette fredette@NetBSD.org Thorsten Frueauf frueauf@NetBSD.org Castor Fu castor@NetBSD.org Makoto Fujiwara mef@NetBSD.org Ichiro Fukuhara ichiro@NetBSD.org Quentin Garnier cube@NetBSD.org Thomas Gerner thomas@NetBSD.org Simon J. Gerraty sjg@NetBSD.org Justin Gibbs gibbs@NetBSD.org Chris Gilbert chris@NetBSD.org Eric Gillespie epg@NetBSD.org Brian Ginsbach ginsbach@NetBSD.org Oliver V. Gould ver@NetBSD.org Paul Goyette pgoyette@NetBSD.org Michael Graff explorer@NetBSD.org Matthew Green mrg@NetBSD.org Andreas Gustafsson gson@NetBSD.org Ulrich Habel rhaen@NetBSD.org Jun-ichiro itojun Hagino itojun@NetBSD.org HAMAJIMA Katsuomi hamajima@NetBSD.org Adam Hamsik haad@NetBSD.org Juergen Hannken-Illjes hannken@NetBSD.org Charles M. Hannum mycroft@NetBSD.org Yorick Hardy yhardy@NetBSD.org Ben Harris bjh21@NetBSD.org Eric Haszlakiewicz erh@NetBSD.org John Hawkinson jhawk@NetBSD.org Emile Heitor imil@NetBSD.org John Heasley heas@NetBSD.org Lars Heidieker para@NetBSD.org Geert Hendrickx ghen@NetBSD.org Rene Hexel rh@NetBSD.org Iain Hibbert plunky@NetBSD.org Kouichirou Hiratsuka hira@NetBSD.org Michael L. Hitch mhitch@NetBSD.org Adam Hoka ahoka@NetBSD.org Jachym Holecek freza@NetBSD.org David A. Holland dholland@NetBSD.org Christian E. Hopps chopps@NetBSD.org Daniel Horecki morr@NetBSD.org Ken Hornstein kenh@NetBSD.org Marc Horowitz marc@NetBSD.org Eduardo Horvath eeh@NetBSD.org Nick Hudson skrll@NetBSD.org Shell Hung shell@NetBSD.org Darran Hunt darran@NetBSD.org Martin Husemann martin@NetBSD.org Dean Huxley dean@NetBSD.org Love Hoernquist Astrand lha@NetBSD.org Roland Illig rillig@NetBSD.org Bernardo Innocenti bernie@NetBSD.org Tetsuya Isaki isaki@NetBSD.org ITOH Yasufumi itohy@NetBSD.org IWAMOTO Toshihiro toshii@NetBSD.org Matthew Jacob mjacob@NetBSD.org Soren Jacobsen snj@NetBSD.org Lonhyn T. Jasinskyj lonhyn@NetBSD.org Darrin Jewell dbj@NetBSD.org Nicolas Joly njoly@NetBSD.org Soren Jorvang soren@NetBSD.org Takahiro Kambe taca@NetBSD.org Antti Kantee pooka@NetBSD.org Frank Kardel kardel@NetBSD.org KAWAMOTO Yosihisa kawamoto@NetBSD.org Min Sik Kim minskim@NetBSD.org KIYOHARA Takashi kiyohara@NetBSD.org Thomas Klausner wiz@NetBSD.org Klaus Klein kleink@NetBSD.org John Klos jklos@NetBSD.org Wayne Knowles wdk@NetBSD.org Takayoshi Kochi kochi@NetBSD.org Jonathan A. Kollasch jakllsch@NetBSD.org Radoslaw Kujawa rkujawa@NetBSD.org Jochen Kunz jkunz@NetBSD.org Martti Kuparinen martti@NetBSD.org Arnaud Lacombe alc@NetBSD.org Kevin Lahey kml@NetBSD.org David Laight dsl@NetBSD.org Johnny C. Lam jlam@NetBSD.org Guillaume Lasmayous gls@NetBSD.org Martin J. Laubach mjl@NetBSD.org Greg Lehey grog@NetBSD.org Ted Lemon mellon@NetBSD.org Christian Limpach cl@NetBSD.org Frank van der Linden fvdl@NetBSD.org Joel Lindholm joel@NetBSD.org Tonnerre Lombard tonnerre@NetBSD.org Mike Long mikel@NetBSD.org Michael Lorenz macallan@NetBSD.org Warner Losh imp@NetBSD.org Tomasz Luchowski zuntum@NetBSD.org Federico Lupi federico@NetBSD.org Brett Lymn blymn@NetBSD.org MAEKAWA Masahide gehenna@NetBSD.org Anders Magnusson ragge@NetBSD.org John Marino marino@NetBSD.org Roy Marples roy@NetBSD.org Cherry G. Mathew cherry@NetBSD.org David Maxwell david@NetBSD.org Gregory McGarry gmcgarry@NetBSD.org Dan McMahill dmcmahill@NetBSD.org Jared D. McNeill jmcneill@NetBSD.org Neil J. McRae neil@NetBSD.org Julio M. Merino Vidal jmmv@NetBSD.org Perry Metzger perry@NetBSD.org Luke Mewburn lukem@NetBSD.org Jean-Yves Migeon jym@NetBSD.org Brook Milligan brook@NetBSD.org Minoura Makoto minoura@NetBSD.org Simas Mockevicius symka@NetBSD.org der Mouse mouse@NetBSD.org Constantine A. Murenin cnst@NetBSD.org Joseph Myers jsm@NetBSD.org Tuomo Maekinen tjam@NetBSD.org Zoltan Arnold NAGY zoltan@NetBSD.org Ken Nakata kenn@NetBSD.org Takeshi Nakayama nakayama@NetBSD.org Alexander Nasonov alnsn@NetBSD.org Phil Nelson phil@NetBSD.org John Nemeth jnemeth@NetBSD.org NISHIMURA Takeshi nsmrtks@NetBSD.org Tohru Nishimura nisimura@NetBSD.org NONAKA Kimihiro nonaka@NetBSD.org Takehiko NOZAKI tnozaki@NetBSD.org Tobias Nygren tnn@NetBSD.org OBATA Akio obache@NetBSD.org Jesse Off joff@NetBSD.org Tatoku Ogaito tacha@NetBSD.org OKANO Takayoshi kano@NetBSD.org Masaru Oki oki@NetBSD.org Ryo ONODERA ryoon@NetBSD.org Atsushi Onoe onoe@NetBSD.org Greg Oster oster@NetBSD.org Jonathan Perkin sketch@NetBSD.org Fredrik Pettai pettai@NetBSD.org Herb Peyerl hpeyerl@NetBSD.org Matthias Pfaller matthias@NetBSD.org Chris Pinnock cjep@NetBSD.org Adrian Portelli adrianp@NetBSD.org Chris Provenzano proven@NetBSD.org Mindaugas Rasiukevicius rmind@NetBSD.org Michael Rauch mrauch@NetBSD.org Marc Recht recht@NetBSD.org Darren Reed darrenr@NetBSD.org Jeremy C. Reed reed@NetBSD.org Jens Rehsack sno@NetBSD.org Antoine Reilles tonio@NetBSD.org Tyler R. Retzlaff rtr@NetBSD.org Scott Reynolds scottr@NetBSD.org Tim Rightnour garbled@NetBSD.org Jeff Rizzo riz@NetBSD.org Hans Rosenfeld hans@NetBSD.org Steve Rumble rumble@NetBSD.org Rumko rumko@NetBSD.org Jukka Ruohonen jruoho@NetBSD.org Blair J. Sadewitz bjs@NetBSD.org David Sainty dsainty@NetBSD.org SAITOH Masanobu msaitoh@NetBSD.org Kazuki Sakamoto sakamoto@NetBSD.org Curt Sampson cjs@NetBSD.org Wilfredo Sanchez wsanchez@NetBSD.org Ty Sarna tsarna@NetBSD.org SATO Kazumi sato@NetBSD.org Jan Schaumann jschauma@NetBSD.org Matthias Scheler tron@NetBSD.org Silke Scheler silke@NetBSD.org Karl Schilke (rAT) rat@NetBSD.org Amitai Schlair schmonz@NetBSD.org Konrad Schroder perseant@NetBSD.org Georg Schwarz schwarz@NetBSD.org Lubomir Sedlacik salo@NetBSD.org Christopher SEKIYA sekiya@NetBSD.org Reed Shadgett dent@NetBSD.org John Shannon shannonjr@NetBSD.org Tim Shepard shep@NetBSD.org Naoto Shimazaki igy@NetBSD.org Ryo Shimizu ryo@NetBSD.org Takao Shinohara shin@NetBSD.org Takuya SHIOZAKI tshiozak@NetBSD.org Daniel Sieger dsieger@NetBSD.org Chuck Silvers chs@NetBSD.org Thor Lancelot Simon tls@NetBSD.org Jeff Smith jeffs@NetBSD.org Noriyuki Soda soda@NetBSD.org Wolfgang Solfrank ws@NetBSD.org Joerg Sonnenberger joerg@NetBSD.org Ignatios Souvatzis is@NetBSD.org T K Spindler dogcow@NetBSD.org Matthew Sporleder mspo@NetBSD.org Bill Squier groo@NetBSD.org Adrian Steinmann ast@NetBSD.org Bill Studenmund wrstuden@NetBSD.org Kevin Sullivan sullivan@NetBSD.org Kimmo Suominen kim@NetBSD.org Gregoire Sutre gsutre@NetBSD.org Sergey Svishchev shattered@NetBSD.org Robert Swindells rjs@NetBSD.org Shin Takemura takemura@NetBSD.org TAMURA Kent kent@NetBSD.org Shin'ichiro TAYA taya@NetBSD.org Hasso Tepper hasso@NetBSD.org Matt Thomas matt@NetBSD.org Jason Thorpe thorpej@NetBSD.org Christoph Toshok toshok@NetBSD.org Greg Troxel gdt@NetBSD.org Tsubai Masanari tsubai@NetBSD.org Izumi Tsutsui tsutsui@NetBSD.org UCHIYAMA Yasushi uch@NetBSD.org Masao Uebayashi uebayasi@NetBSD.org Shuichiro URATA ur@NetBSD.org Valeriy E. Ushakov uwe@NetBSD.org Todd Vierling tv@NetBSD.org Aymeric Vincent aymeric@NetBSD.org Paul Vixie vixie@NetBSD.org Mike M. Volokhov mishka@NetBSD.org Krister Walfridsson kristerw@NetBSD.org Mark Weinem weinem@NetBSD.org Lex Wennmacher wennmach@NetBSD.org Leo Weppelman leo@NetBSD.org Assar Westerlund assar@NetBSD.org Frank Wille phx@NetBSD.org Nathan Williams nathanw@NetBSD.org Rob Windsor windsor@NetBSD.org Jim Wise jwise@NetBSD.org Colin Wood ender@NetBSD.org Steve Woodford scw@NetBSD.org YAMAMOTO Takashi yamt@NetBSD.org Yuji Yamano yyamano@NetBSD.org David Young dyoung@NetBSD.org Arnaud Ysmal stacktic@NetBSD.org Reinoud Zandijk reinoud@NetBSD.org S.P.Zeidler spz@NetBSD.org Tim Zingelman tez@NetBSD.org Christos Zoulas christos@NetBSD.org Legal Mumbo-Jumbo All product names mentioned herein are trademarks or registered trade- marks of their respective owners. The following notices are required to satisfy the license terms of the software that we have mentioned in this document: NetBSD is a registered trademark of The NetBSD Foundation, Inc. This product includes software developed by the University of California, Berkeley and its contributors. This product includes software developed by the NetBSD Foundation. This product includes software developed by The NetBSD Foundation, Inc. and its contributors. This product includes software developed for the NetBSD Project. See http://www.netbsd.org/ for information about NetBSD. This product includes software developed by Intel Corporation and its contributors. This product includes cryptographic software written by Eric Young (eay@cryptsoft.com) This product includes cryptographic software written by Eric Young (eay@mincom.oz.au) This product includes software designed by William Allen Simpson. This product includes software developed at Ludd, University of Lulea, Sweden and its contributors. This product includes software developed at Ludd, University of Lulea. This product includes software developed at the Information Technology Division, US Naval Research Laboratory. This product includes software developed by David Jones and Gordon Ross This product includes software developed by Hellmuth Michaelis and Joerg Wunsch This product includes software developed by Internet Research Institute, Inc. This product includes software developed by Leo Weppelman and Waldi Ravens. This product includes software developed by Mika Kortelainen This product includes software developed by Aaron Brown and Harvard Uni- versity. This product includes software developed by Adam Ciarcinski for the NetBSD project. This product includes software developed by Adam Glass and Charles M. Hannum. This product includes software developed by Adam Glass. This product includes software developed by Advanced Risc Machines Ltd. This product includes software developed by Alex Zepeda, and Colin Wood for the NetBSD Projet. This product includes software developed by Alex Zepeda. This product includes software developed by Amancio Hasty and Roger Hardiman This product includes software developed by Berkeley Software Design, Inc. This product includes software developed by Bill Paul. This product includes software developed by Bodo Moeller. (If available, substitute umlauted o for oe) This product includes software developed by Boris Popov. This product includes software developed by Brini. This product includes software developed by Bruce M. Simpson. This product includes software developed by Causality Limited. This product includes software developed by Charles Hannum. This product includes software developed by Charles M. Hannum, by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Laboratory, and its contributors. This product includes software developed by Charles M. Hannum. This product includes software developed by Christian E. Hopps, Ezra Story, Kari Mettinen, Markus Wild, Lutz Vieweg and Michael Teske. This product includes software developed by Christian E. Hopps. This product includes software developed by Christopher G. Demetriou for the NetBSD Project. This product includes software developed by Christopher G. Demetriou. This product includes software developed by Christos Zoulas. This product includes software developed by Chuck Silvers. This product includes software developed by Colin Wood for the NetBSD Project. This product includes software developed by Colin Wood. This product includes software developed by Daan Vreeken. This product includes software developed by Daishi Kato This product includes software developed by Daniel Widenfalk and Michael L. Hitch. This product includes software developed by Daniel Widenfalk for the NetBSD Project. This product includes software developed by Dean Huxley. This product includes software developed by Eric S. Hvozda. This product includes software developed by Eric S. Raymond This product includes software developed by Eric Young (eay@@min- com.oz.au) This product includes software developed by Eric Young (eay@crypt- soft.com) This product includes software developed by Eric Young (eay@mincom.oz.au) This product includes software developed by K. Kobayashi. This product includes software developed by K. Kobayashi and H. Shimokawa. This product includes software developed by Ezra Story and by Kari Met- tinen. This product includes software developed by Ezra Story, by Kari Mettinen and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, Michael Teske and by Bernd Ernesti. This product includes software developed by Ezra Story, by Kari Mettinen, and Michael Teske. This product includes software developed by Ezra Story. This product includes software developed by Florian Stoehr. This product includes software developed by Frank van der Linden for the NetBSD Project. This product includes software developed by Gardner Buchanan. This product includes software developed by Garrett D'Amore. This product includes software developed by Gary Thomas. This product includes software developed by Gordon Ross This product includes software developed by Harvard University and its contributors. This product includes software developed by Harvard University. This product includes software developed by Henrik Vestergaard Draboel. This product includes software developed by Herb Peyerl. This product includes software developed by Hidetoshi Shimokawa. This product includes software developed by Ian W. Dall. This product includes software developed by Ignatios Souvatzis for the NetBSD Project. This product includes software developed by Internet Initiative Japan Inc. This product includes software developed by James R. Maynard III. This product includes software developed by Jason L. Wright This product includes software developed by Jason R. Thorpe for And Com- munications, http://www.and.com/ This product includes software developed by Joachim Koenig-Baltes. This product includes software developed by Jochen Pohl for The NetBSD Project. This product includes software developed by Joerg Wunsch This product includes software developed by John Birrell. This product includes software developed by John P. Wittkoski. This product includes software developed by John Polstra. This product includes software developed by Jonathan R. Stone for the NetBSD Project. This product includes software developed by Jonathan Stone and Jason R. Thorpe for the NetBSD Project. This product includes software developed by Jonathan Stone. This product includes software developed by Julian Highfield. This product includes software developed by Kazuhisa Shimizu. This product includes software developed by Kazuki Sakamoto. This product includes software developed by Kenneth Stailey. This product includes software developed by Kiyoshi Ikehara. This product includes software developed by Klaus Burkert,by Bernd Ernesti, by Michael van Elst, and by the University of California, Berke- ley and its contributors. This product includes software developed by LAN Media Corporation and its contributors. This product includes software developed by Lloyd Parkes. This product includes software developed by Lutz Vieweg. This product includes software developed by MINOURA Makoto, Takuya Harakawa. This product includes software developed by Marc Horowitz. This product includes software developed by Marcus Comstedt. This product includes software developed by Mark Brinicombe for the NetBSD project. This product includes software developed by Mark Brinicombe. This product includes software developed by Mark Tinguely and Jim Lowe This product includes software developed by Markus Wild. This product includes software developed by Masanobu Saitoh. This product includes software developed by Masaru Oki. This product includes software developed by Matthew Fredette. This product includes software developed by Michael Smith. This product includes software developed by Mike Pritchard. This product includes software developed by Mike Pritchard and contribu- tors. This product includes software developed by Minoura Makoto. This product includes software developed by Niels Provos. This product includes software developed by Niklas Hallqvist, Brandon Creighton and Job de Haas. This product includes software developed by Niklas Hallqvist. This product includes software developed by Paul Kranenburg. This product includes software developed by Paul Mackerras. This product includes software developed by Per Fogelstrom This product includes software developed by Peter Galbavy. This product includes software developed by Phase One, Inc. This product includes software developed by Philip A. Nelson. This product includes software developed by RiscBSD. This product includes software developed by Roar Thronaes. This product includes software developed by Rodney W. Grimes. This product includes software developed by Roger Hardiman This product includes software developed by Rolf Grossmann. This product includes software developed by Ross Harvey for the NetBSD Project. This product includes software developed by Ross Harvey. This product includes software developed by Scott Bartram. This product includes software developed by Scott Stevens. This product includes software developed by Shingo WATANABE. This product includes software developed by Softweyr LLC, the University of California, Berkeley, and its contributors. This product includes software developed by Stephan Thesing. This product includes software developed by Steven M. Bellovin. This product includes software developed by Takashi Hamada. This product includes software developed by Takumi Nakamura. This product includes software developed by Tatoku Ogaito for the NetBSD Project. This product includes software developed by Terrence R. Lambert. This product includes software developed by TooLs GmbH. This product includes software developed by Trimble Navigation, Ltd. This product includes software developed by WIDE Project and its contrib- utors. This product includes software developed by Waldi Ravens. This product includes software developed by Wasabi Systems for Zembu Labs, Inc. http://www.zembu.com/ This product includes software developed by Winning Strategies, Inc. This product includes software developed by Wolfgang Solfrank. This product includes software developed by Yasushi Yamasaki. This product includes software developed by Yen Yen Lim and North Dakota State University. This product includes software developed by Zembu Labs, Inc. This product includes software developed by the Alice Group. This product includes software developed by the Center for Software Sci- ence at the University of Utah. This product includes software developed by the Charles D. Cranor, Wash- ington University, University of California, Berkeley and its contribu- tors. This product includes software developed by the Computer Systems Engi- neering Group at Lawrence Berkeley Laboratory. This product includes software developed by the David Muir Sharnoff. This product includes software developed by the Harvard University and its contributors. This product includes software developed by the Network Research Group at Lawrence Berkeley Laboratory. This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http://www.OpenSSL.org/) This product includes software developed by the PocketBSD project and its contributors. This product includes software developed by the RiscBSD kernel team This product includes software developed by the RiscBSD team. This product includes software developed by the SMCC Technology Develop- ment Group at Sun Microsystems, Inc. This product includes software developed by the University of California, Berkeley and its contributors, as well as the Trustees of Columbia Uni- versity. This product includes software developed by the University of California, Lawrence Berkeley Laboratory and its contributors. This product includes software developed by the University of California, Lawrence Berkeley Laboratory. This product includes software developed by the University of Illinois at Urbana and their contributors. This product includes software developed by the Urbana-Champaign Indepen- dent Media Center. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman. This product includes software developed by the University of Vermont and State Agricultural College and Garrett A. Wollman, by William F. Jolitz, and by the University of California, Berkeley, Lawrence Berkeley Labora- tory, and its contributors. This product includes software developed for the FreeBSD project This product includes software developed for the NetBSD Project by Bernd Ernesti. This product includes software developed for the NetBSD Project by Christopher G. Demetriou. This product includes software developed for the NetBSD Project by Emmanuel Dreyfus. This product includes software developed for the NetBSD Project by Frank van der Linden This product includes software developed for the NetBSD Project by Igna- tios Souvatzis. This product includes software developed for the NetBSD Project by Jason R. Thorpe. This product includes software developed for the NetBSD Project by John M. Vinopal. This product includes software developed by Kyma Systems. This product includes software developed for the NetBSD Project by Kyma Systems LLC. This product includes software developed for the NetBSD Project by Matthias Drochner. This product includes software developed for the NetBSD Project by Perry E. Metzger. This product includes software developed for the NetBSD Project by Scott Bartram and Frank van der Linden This product includes software developed for the NetBSD Project by Alle- gro Networks, Inc., and Wasabi Systems, Inc. This product includes software developed for the NetBSD Project by Genetec Corporation. This product includes software developed for the NetBSD Project by Jonathan Stone. This product includes software developed for the NetBSD Project by Pier- mont Information Systems Inc. This product includes software developed for the NetBSD Project by SUNET, Swedish University Computer Network. This product includes software developed for the NetBSD Project by Shigeyuki Fukushima. This product includes software developed for the NetBSD Project by Wasabi Systems, Inc. This product includes software developed under OpenBSD by Per Fogelstrom Opsycon AB for RTMX Inc, North Carolina, USA. This product includes software developed under OpenBSD by Per Fogelstrom. This software is a component of "386BSD" developed by William F. Jolitz, TeleMuse. This software was developed by Holger Veit and Brian Moore for use with "386BSD" and similar operating systems. "Similar operating systems" includes mainly non-profit oriented systems for research and education, including but not restricted to "NetBSD", "FreeBSD", "Mach" (by CMU). This software includes software developed by the Computer Systems Labora- tory at the University of Utah. This product includes software developed by Computing Services at Carnegie Mellon University (http://www.cmu.edu/computing/). This product includes software developed by Marshall M. Midden. This product includes software developed or owned by Caldera Interna- tional, Inc. The Institute of Electrical and Electronics Engineers and The Open Group, have given us permission to reprint portions of their documentation. In the following statement, the phrase ``this text'' refers to portions of the system documentation. Portions of this text are reprinted and reproduced in electronic form in NetBSD, from IEEE Std 1003.1, 2004 Edition, Standard for Information Technology -- Portable Operating System Interface (POSIX), The Open Group Base Specifications Issue 6, Copyright (C) 2001-2004 by the Institute of Electrical and Electronics Engineers, Inc and The Open Group. In the event of any discrepancy between these versions and the original IEEE and The Open Group Standard, the original IEEE and The Open Group Standard is the referee document. The original Standard can be obtained online at http://www.opengroup.org/unix/online.html. This notice shall appear on any product containing this material The End NetBSD September 22, 2014 NetBSD